活塞閥桿 的英文怎麼說
中文拼音 [huósèfágǎn]
活塞閥桿
英文
piston valve spindle-
One machinery makes wen zhoudong limited company is to be engaged in research, development, production, sale is domestic and international the gas a powerful person of all sorts of medium compressor, a powerful person piece, lever of annulus of bedspring, piston, piston, piston, sealing ring, crosshead, crosshead is sold, copper is covered, bolt of connecting rod, connecting rod,
溫州東一機械製造有限公司是從事研究、開發、生產、銷售國內外各種介質壓縮機的氣閥、閥片、彈簧、活塞、活塞環、活塞桿、密封圈、十字頭、十字頭銷、銅套、連桿、連桿螺栓、軸瓦、曲軸、缸體及缸蓋、缸套、凈化設備及部件、冷卻器等壓縮機配件的專業技術型企業。The structure and operating principle of an air - charged split - type adjustable shock absorber was described, e non - linear parameterized mathematical model of this shock absorber ' s damping characteristics was established according to fluid mechanics theory and the main structural affection factors to shock absorber ' s damping performance, such as the diameter of piston valve orifice, the diameter of adjustable orifice, the initial volume of gas chamber, the diameter of piston rod, the inner diameter of oil pipe and so on, were analyzed by simulations
摘要通過分析一種分體式充氣可調阻尼減振器的結構和工作原理，運用流體力學理論，建立了該減振器阻尼特性的非線性參數化模型，模擬分析了活塞阻尼閥孔徑、阻尼調節孔徑、氣室初始體積、活塞桿直徑、油管內徑等主要結構參數對減振器阻尼性能的影響，通過試驗測試，得到了減振器樣件的阻尼特性及其可調范圍。There is no clutch, gearing, oil changes, smog check, pistons, rings, valves, crankshaft, flywheel, rods, wrist pins, etc., etc
沒有離合器，傳動裝置，機油變化，尾氣檢查，活塞，活塞環，閥門，曲軸，飛輪，連桿，肘節銷，等等。Hydraulic concrete crusher detail : all round, extremely efficient concrete crusher system for concrete demolition in general, and reinforcement exposure in particular. the system works immissionfree, i. e. : it does not produce any noise, dust or cibrations and operates without water. description : pliers qty 1, hydraulic power pack qty 1, 10m long oil pipe set of hoses, high pression qty 2, accessories bag qty 1
啟動電機帶動油泵運轉，液壓油直接返回油箱手動轉動換向閥三位四通閥一個位置后，液壓油進入系統推動活塞，活塞桿伸出，帶動鉗體收縮，從而破碎鋼筋混凝土結構，反向轉動換向閥，鉗體松開，完成一個工作循環。Control valve piston rod
控制閥活塞桿When the electrohydraulic push rod works, if the external force suffered by the piston rod is more than the setting output torque, the piston moves to the end ; oil pressure in the oil pipeline increases rapidly to the setting value, the safety valve overflows rapidly, to achieve overload protection
電液推桿工作時，當活塞桿所受外力超過調定的輸出力距活塞運動到終點；油路中的油壓迅速增高至調定值，安全閥迅速溢流，實現過載保護。This thesis gaved a detail account to the main part. for example : the design of the cylinder and the piston rod ; the time calculate of the valve ; the design of the disc spring and how to use it
根據斷路器的要求進行了彈簧液壓機構的主要液壓元件的設計：集成式工作缸和變截面活塞桿結構設計；電磁閥、控制閥系統結構設計及動作時間的近似計算；儲能碟形彈簧的結構設計、應力計算及選用方法。Instead, the motor rotate reversely, push rod ( piston rod ) push out, the valve plate closes, stops discharging
反之，電機反轉，推桿（活塞桿）推出，閥板關閉，停止卸料。Suitable for each type of dual - surface molding, for example, spring end, bearing, magnet, connecting rod, piston ring, compressor valve and etc
適用於各種雙面加工例如：彈簧端面培林磁鐵連桿活塞環壓縮機閥片等。( 2 ) in the original system because of the area between the piston and the piston pole is too small, the system pressure will rise when in the return stroke. and the reliever valve will open. the return velocity will reduce
（ 2 ）原設計中，由於活塞和活塞桿的面積差很小，回程上行時，系統壓力會迅速升高造成溢流閥的溢流而使回程速度降低，從而降低了系統的工作效率。When discharging, the motor operates, hydraulic cylinder charges pressure, push rod ( piston rod ) draw back, the valve plate connected with push rod opens, the materials are discharged
當需要卸料時，電機運轉，液壓缸增壓，推桿（活塞桿）收回，和推桿連接的閥板開啟，物料卸下。Electrohydraulic push rod drives the two - way pump to output pressure oil with rotation of motor clockwise and counter - clockwise, by control of hydraulic valve, send to the hydraulic cylinder, to achieve the reciprocating movement of the piston rod
電液推桿以電動機正反轉，帶動雙向泵輸出壓力油，經液壓閥控制，送至液壓缸，實現活塞桿的往復運動。分享友人