浸出工段 的英文怎麼說
中文拼音 [jìnchūgōngduàn]
浸出工段
英文
extractor room-
The control system of furnace " s temperature has been widely used in every walk of life, as an important link of repair and manufacture of the electrical equipment such as electromotor transformer etc., soaking lacquer drying craft has some especial requests on drying crafto this article starts with the analysis of drying chamber " s configuration, analyzed its configuration limitation and control function limitation according to the factory " s situation and advances the conception of heated air drying circulation, in addition, this article adopts an intellectualize a / d module, a development sampling tuning - voltage circuit, and presents the method to measure online the insulation resistance of products in order to improve constantly products quality
而浸漆乾燥工藝作為電機、變壓器等電氣設備的修理、製造中的重要環節之一，對乾燥過程的質量要求有一定的特殊性。該文從乾燥爐的結構分析入手，聯繫到工廠的實際情況分析了結構功能缺陷和控制功能缺陷，提出了熱風循環乾燥的概念，同時，選擇了較為先進的a d板卡、熱電阻信號調理板等專業化智能卡，運用數字pid控制技術，構成了一個較有特色的計算機控制系統。此外，該文還從保證乾燥品質量的角度，採用智能化交流模塊和自製采樣調壓電路的方法，提出了在線檢測產修品的絕緣電阻的方法和手段，以確保企業產品質量不斷提高。Liquid - solid extrusion of composite material is a new kind of metal forming process, which has been developed in recent years with a promising practical application prospect for its simple working procedure, low cost and good workpiece performance. through a lot of experiments, the optimization and chosing method of key process parameters ( pouring temperature, mold warm - up temperature, impregnating pressure, impregnating time ) has been mastered. under the precondition of appropriate chosing these parameters, the effective control of extrusion velocity is the key of mading good workpiece. but the control of extrusion velocity remains a handwork, and it is heavily affected by such uncertainties as a handler ' s knowledge and skill about the process. in order to solve the problem, the automatic control of the extrusion velocity is studied, and a computer control system is also designed under existing condition
通過大量實驗，已掌握了關鍵工藝參數（熔液澆注溫度、擠壓模預熱溫度、浸漬時間、浸漬力）的優化選取方法。在合理選取關鍵工藝參數的前提下，擠壓速度的控制是成形出質量良好製件的關鍵。但是，目前對于擠壓速度的控制仍停留在手動控制階段，利用該工藝制備管、棒材製件的成功與否受操作者對該工藝及其設備的經驗及熟練程度等不確定因素影響很大。The old lo wu railway bridge and the lo wu old pedestrian bridge formed a serious bottleneck for flood flows. upon completion of the bridge work and improvement of the river section at lo wu in early 2004, the bottleneck at lo wu will be removed and the flooding risk upstream of lo wu can be reduced in time for the 2004 wet season
他指出，現有的羅湖鐵路橋和羅湖舊行人橋形成嚴重的瓶頸地帶，這兩條橋的重建工程以及羅湖河段的改善工程於二四年年初完成後，羅湖的瓶頸地帶將會消失，而羅湖上游在二四年雨季的水浸風險亦將會減少。
分享友人