浸漬塗料 的英文怎麼說

中文拼音 [jìnzìtúliào]
浸漬塗料 英文
dicoatings
  • 浸 : Ⅰ動詞1 （泡在液體里） soak; steep; immerse 2 （液體滲入） soak; saturate; steep Ⅱ副詞[書面語] （...
  • 漬 : Ⅰ名詞1 （地面的積水） floodwater on low lying land 2 [方言] （積在物體上難以除去的油泥等） stain;...
  • 塗 : Ⅰ動詞1 （抹） spread on; apply; smear 2 （亂寫或亂畫） scrawl; scribble 3 （抹去） cross [blot; s...
  • 料 : 名詞1 （材料; 原料） material; stuff 2 （喂牲口用的穀物） feed; fodder 3 （料器） glassware 4 （...
  • 塗料 : coating material; paint; coating; daubing; dope; moldwash
  1. The results showed that : there were five stages in the rising process of the internal temperature of untreated, fire - retardant solution soaked, and fire - proof paint coated wood during the fire ; the carbonization rate of wood decreased by 21. 1 % ~ 35. 6 % and the rising speed of internal temperature also declined greatly when wood was soaked in fire - retardant solution or coated with fireproof paint ; the carbonization rate of white pine was 8. 5 % ~ 17. 4 % higher than that of the northeast china ash ; for untreated wood, the carbonization rate in tangential direction was 5. 8 % ~ 10. 5 % higher than that in radial direction ; the internal temperature of wood varies with the developing direction of combustion

    結果表明：火災發生過程中未處理木材、阻燃浸漬處理和塗刷防火徐料木材內部溫度上升過程出現5個階段；經過阻燃浸漬處理和塗刷防火塗料后，木材的燃燒炭化速度降低了21 . 1 % ~ 35 . 6 % ，內部溫度上升速度大幅度下降；白皮松木材的燃燒炭化速度比水曲柳木材的燃燒炭化速度快8 . 5 % ~ 17 . 4 % ；未處理木材沿弦向的燃燒炭化速度比徑向快5 . 8 % ~ 10 . 5 % ；木材內部的溫度變化沿燃燒推進方向不同而不同。
  2. In order to make clear the regulation of the combustion and the heat - transport process of fire - retardant treated wood, the combustion of untreated, fire - retardant solution soaked, and fire - proof paint coated white pine ( pinus bungeana ) and northeast china ash ( fraxinus mandshurica ) wood as well as the rising process of temperature at different sites in wood were measured in this study, taking a multi - function fire - proof experiment oven to simulate the typical process of fire

    摘要為了弄清楚阻燃處理木材的燃燒及其熱傳導規律，該研究採用多功能耐火實驗爐模擬典型火災的發生過程，測定了未處理、阻燃劑水溶液浸漬處理、塗刷防火塗料白皮松和水曲柳木材的燃燒及木材內不同位置的升溫過程。
  3. Paints and varnishes - corrosion test by alternate immersion in a buffered sodium chloride solution

    塗料和清漆.在緩沖氯化納溶劑中用更迭浸漬試驗測定耐蝕性
  4. Aerospace series. paints and varnishes. corrosion test by alternate immersion in a buffered sodium cloride solution

    航空航天系列.塗料和清漆.用交替浸漬在含有緩沖劑的氯化納溶劑中進行腐蝕試驗
  5. Aerospace industry. paints and varnishes. determination of the water resistance. method by immersion in de - ionized water

    航空航天工業.塗料和清漆.耐水性的測定.用去離子水浸漬法
  6. Paints and varnishes - corrosion testing by alternate immersion in and removal from a buffered sodium chloride solution

    油漆和清漆.將塗料替換浸漬在緩沖氯化鈉溶液中和從該溶液中去除的腐蝕試驗
  7. Focusing on serious damage of carbon fibers in ceramic matrix composites ( cmcs ) prepared by precursor infiltration pyrolysis ( pip ), and with emphasis on carbon fiber reinforced silicon carbide composites ( cf / sic ) derived from polycarbosilane ( pcs ), the influences of raw materials ( including carbon fibers and precursors, etc. ) and preparing conditions on carbon fiber damage during the preparation of cf / sic composites were investigated systemically. pyrolysis process, fiber - matrix interface and carbon fiber damage process were observed by sem, tem, ir, xrd, xps and tq etc. the characterization method of carbon fiber damage degree was established and the models for carbon fiber damage mechanism were also established. the carbon fiber coatings and unidirectional cf / sic composites with coated carbon fibers were prepared and studied

    本文針對先驅體浸漬裂解工藝制備陶瓷基復合材料過程中碳纖維損傷嚴重的問題，以聚碳硅烷（ pcs ）制備cf / sic復合材料為重點，採用sem 、 tem 、 ir 、 xrd 、 xps 、 tg等表徵手段，分析了先驅體裂解過程、纖維基體界面和碳纖維損傷過程，系統地研究了原料（碳纖維、先驅體等）和制備工藝條件等在cf / sic復合材料制備過程中對碳纖維損傷的影響，建立了碳纖維損傷程度的表徵方法和損傷機理模型，制備了纖維表面塗層並利用塗層碳纖維制備了單向cf / sic復合材料。
分享友人
分享到 Line

分享到臉書