消弧電壓 的英文怎麼說
中文拼音 [xiāohúdiànyā]
消弧電壓
英文
extinction voltage of arc-
According to the quickly adjustable characteristic of the peterson coil grounding system, this dissertation proposes a new control strategy. when the system is in operation, the strategy can limit the series resonance over - voltage by using the off - resonance method. when fault occurs, the strategy can conveniently suppressing arc by rapidly adjusting the inductance value of the peterson coil to the point, which the resonance with grounding capacitance of the power network is occurred
依據可控硅控制消弧線圈接地系統的快速可控性，一改傳統的電網正常運行時調節消弧線圈接近於全補償的預調諧方法，提出正常運行時採用脫諧方法抑制串聯諧振過電壓；故障時立即調節消弧線圈電感量達到與對地電容諧振，以利熄弧的新型調節原理和方法。Based on researching the function of every kind of eliminating arc loop, new concept was brought up in this paper, and the protective device for eliminating arc and overvoltage was researched and manufactured. when the arc light connecting the ground emerges, the chip synthesizing controller control the vacuum contacter which can be operated with dividing phase and make its fault phase earthed so that the arc light can be dissolved thoroughly
本文在研究各種消弧線圈的基礎上，提出全新的概念，研製出了消弧及過電壓保護裝置，該裝置在出現弧光接地時，通過單片機綜合控制器控制一組可以分相操作的真空接觸器，使故障相接地，達到徹底消除弧光的目的。Rapid prototyping technology changed the traditional pattern of product design, which could offer product sample for the designer, reduced design cycle and quicken the schedule of new product design, and it gave the decision - makers visual feeling. ; rp technology provided kinds of molds including resin - boncled mold laminate mold, investment mold and lost foam casting mold and so on for sand casting investment casting and cavityless casting, it could also use direct shell production casting to make pattern dies metal dies die - casting dies injection dies directly, and it could even produce casting products in small scales. the applications of fdm technology in plaster precision casting and the rapid casting technology based on sls technology were introduced, the organic combination between rapid prototyping tecnnology and foundry process, which initiated a new period of rapid manufacturing metal parts, by using advanced new technology alternated traditional foundry industry to make it looked brand - new, thus, the competition of foundry industry would be improved ; rapid prototyping technology offered a rapid economical feasible technical method, common processes of using rapid prototyping technology to produce dies were discussed, in the paper it explored that. the problem of combining rapid prototyping technology with electric arc metal - spraying technology to make metal dies and technics in dies manufacturing of combining rapid prototyping technology with precision casting, rapid tooling based on rapid prototyping, integrated advanced new technology and tradition technology of rapid prototyping manufacture, each superiority were exerted, rapid prototyping technology had been an efficiency measure to rapid update products and develop new product, and to middle -
快速成型技術改變了傳統的產品開發模式，可以為設計者提供產品樣件，縮短設計周期，加快新產品的開發進度，為決策者提供直觀性；快速成型技術迅速提供砂型鑄造、熔模鑄造、實型鑄造用的各種模樣，包括樹脂模、層壓模、熔模和消失模等，還可採用直接制殼鑄造法直接製造熔模鑄造用的壓型、金屬型、壓鑄型、注塑模，甚至直接製造小批量鑄件，介紹了熔積成型技術在石膏型精密鑄造上的應用和基於選擇性激光燒結技術的快速鑄造技術，快速成型技術與鑄造工藝的有機結合，開創了快速製造金屬零件的新階段，對用高新技術改造傳統的鑄造工業，使其面貌煥然一新，增強鑄造行業的競爭能力；快速成型技術為母模的製造提供了一條快速、經濟、可行的技術途徑，討論了利用快速成型技術製造模具的一般工藝方法，探討了將快速成型技術與金屬電弧噴鍍技術結合起來快速製造金屬模具問題，以及快速成型技術與精密鑄造技術相結合的模具製造工藝，基於快速成型製造的快速模具技術，集成了快速成型製造高新技術和傳統技術，發揮各自優勢，已成為產品快速更新換代和新產品開發及中、小批量生產的有效手段之一。The problem about neutral - point - grounding mode is an all - around technical problem which associated with not only power system reliability ， insulation coordination ， electromagnetic interference ， but assault safety 。 in china ， the neutral grounding modes of the 10kv net involved of none grounding, grounding by arc suppressing coils, resistance grounding or reactance grounding in the past 。 with the development of civic power network ， low resistance grounding mode was used to restrain the over voltage, particularly in guangzhou, shanghai ， beijing ， and zhuhai etc. it was reported that the over - voltage level of low resistance grounding mode is lower than that of arc suppressing coil mode, but the operation carried out the other way 。 at substations in guangzhou and shanghai it was found that the low resistance grounding mode is successful 。 but in some areas ， such as zhuhai ， substations grounding with low resistance revealed some problems ， including power supply reliability rapidly dropping ， transmitting line often tripping ； and person safety being threatened 。 so interiorly the grounding mode selection of the 10kv network was disputed, which mainly focused on the fault form of 10kv net grounding, the apply area of suppressing arcing coil grounding mode, power supply reliability level of the two modes, person safety, communication interfere and the workload of maintenance
爭議點主要是在10kv電網接地故障的形式、消弧線圈接地的應用范圍、兩種運行方式供電可靠性的高低、人身安全、通訊干擾和運行維護工作量等諸多方面。 11 17本論文就是針對以電纜為主的城區10kv電網中性點接地方式的選擇問題進行研究。論文首先對10kv電網的中性點運行各種方式進行分析，比較各方式的特點，然後以重慶儲奇門變電站10kv電網的實際參數來建立數值計算模型，在考慮了電網接地電容電流變化、中性點電阻取值大小、接地點接地電阻值變化等多種影響因素的情況下，對中性點經消弧線圈接地和經小電阻接地方式下電網的過電壓水平和接地點短路電流大小進行了數值計算，其計算結果與電科院所作現場試驗進行了比較。By improving surface condition of parts and one shot seal - off clean room grade, using ultrasonic vapor phase cleaning process, the inner parts of vacuum interrupter get cleaner. movable particles have been diminished by automatic current ageing, power frequency hi - voltage ageing and dynamic high current ageing. as the dielectric strength of clearance in vacuum interrupter improved, the probability of re - ignition in test drops evidently
通過提高零件表面加工質量，改善一次封排間的真空衛生條件、制定合理的超聲波氣相清洗工藝提高管內潔凈度，採用自動電流老煉、超高壓工頻老煉、大電流動態老煉等工藝進一步消除真空滅弧室內活動性微粒，可提高真空滅弧室真空間隙介質強度，使真空開關投切電容器組的重燃率大大降低，並通過實驗驗證真空開關投切電容器組的重燃率在製造工藝改進後由原來的10 . 7 %降低至1 . 3 % 。The tap - changer is made with solid state relay as its working mechanism and controlled by microprocessor. this switch has totally cancelled the mechanical drive organization, by the microprocessor according to the voltage of second side microprocessor decide the working condition of solid state rely, high regulation speed, need not transition resistor, rush current is low. operating frequently ; there is no electric arc to produce, can put in the fuel tank of the voltage transformer directly ; the structure is simple, the fabrication cost is low, benefit and use widely among the voltages transformer of distribution
其中的有載調壓分接開關，它是一種完全由固態繼電器作為分接開關執行機構，由單片機控制的有載自動調壓的變壓器分接開關。該開關完全取消了機械傳動機構，由單片機根據變壓器二次側電壓的高低，決定與變壓器各分接頭聯接的固態繼電器的工作狀態。調節速度快，改變分接頭時不需過渡電阻，沖擊電流小，可頻繁操作；無電弧產生，可以直接放在變壓器油箱中；結構簡單，造價低，便於在配電變壓器中推廣使用。Arc suppressing varistor
消弧電壓敏電阻器Arc suppressing varstor
消弧電壓敏電阻器It depends on many factors. in our country, middle and low voltage distribute net system uses non - direct - grounded system including no - grounded system and anti - arc system
我國中低壓配電網多採用小電流接地系統，即中性點不接地或者經消弧線圈接地。After the neutral point is grounded through perterson coil, it can decrease the capacitor current through fault point and the over - voltage caused by the grounding fault, which is advantage for the extinguishments of electric arc
中性點經消弧線圈接地后，有效減小了流過故障點的電容電流，減小了弧光接地過電壓，有利於電弧熄滅。After the neutral point is grounded through peterson coil, it can decrease the capacitor current through fault point and the over - voltage caused by the grounding fault, which is advantage for the extinguishments of electric arc
中性點經消弧線圈接地后，有效地減小了流過故障點的電容電流，減小了弧光接地過電壓，有利於電弧熄滅。It can be predicated that the study results are useful to the design of overvoltage protective device in electric power system and the development of canceling arc light earthed overvoltage device and small electric current chosen equipment
本文的研究結果對電力系統過電壓保護裝置的設計及消除弧光接地過電壓和小電流選線裝置的開發具有實際指導意義。By adjusting the automatic tracing coil of arc extinction for switch stand and analysing technical parameters of arc extinction coil in normal operation, the paper indicates some problems should be taken care of, so as to operate properly automatic tracing coil, to remove the excess voltage of grounded arc and to ensure reliable power supply
摘要通過調試開關站自動跟蹤消弧線圈，分析自動跟蹤消弧線圈正常運行技術參數，指出設計運行中應注意的問題，保證自動跟蹤消弧線圈正常運行，消除弧光接地過電壓，保證可靠供電。The fast development of power system has made it more and more imperative to measure transient parameters, such as over voltage test, trial engagement test of switches, reactors and transformers, harmonics elimination test of arc elimination coils and trial operation of high voltage transmission lines
隨著電力系統的飛速發展，對于暫態參數的測量需求越來越迫切，例如：過電壓試驗；開關、電抗器、變壓器投切試驗、消弧線圈消諧試驗、高壓線路的試投等。In china, neutral isolated and peterson coil grounded system are widely used in 6 kv ~ 35kv medium voltage distribution networks
我國大多數6 35kv中壓配電網均採用中性點不接地或經消弧線圈接地的運行方式。According to the present actual underground power system which neutral point is grounded through arc suppression coil in many supper big shaft, the development history and present situation of synthetic protection system used in hv flameproof switchgear are reviewed, and on the basis of analyzing the problems existed in high voltage flameproof switchgear, the selective leakage protective method based on the detecting harmonic direction of zero sequence current as well as the value of zero sequence voltage is proposed in this paper, and at the same time, harmonics extracting schematic and transforming circuit are also designed
本文深入系統地研究了基於intel80c196kb單片機控制的6kv防爆開關綜合保護系統，主要內容如下：針對大型及特大型礦井供電系統中性點普遍採用消弧線圈接地方式的現狀，回顧了國內外礦用高壓防爆開關保護系統的發展歷史，分析了目前國內高壓饋電開關保護系統所存在的問題，提出了「基於零序電壓基波啟動，五次諧波功率方向比較」的選擇性漏電保護原理，設計了相應的五次諧波提取電路和功率方向鑒別電路。A novel structure of peterson coil with particular design can fully satisfy above requirements and allow us to use the lower critical voltage - level thyristor in the 6 - 10kv and higher voltage power system. the novel peterson coil design resolves key problems of using thyristor to control the peterson coil, and becomes the foundation of realizing quick adjustment of the inductance value of the peterson coil
由於其特有的諧波問題、耐壓問題等，本論文涉及的一種新型消弧線圈，通過消弧線圈的特殊設計，使常規耐壓范圍的可控硅技術可以應用於6 - 10kv和更高電壓等級的系統，解決了可控硅控制應用於消弧線圈的根本問題，為實現電感量的快速調節打下了基礎。Association with the situation of china, the solution is grounding the neuter point by peterson coil which will decrease the fault current and improve the human security. but it also brings two problems : first, the improper compensation will cause over voltage ; second, it ’ s hard to fault select
但是，中性點經消弧線圈接地后存在兩方面的問題:首先，消弧線圈調諧不當易產生諧振過電壓;其次，在中性點經消弧線圈接地系統中，發生單相接地時故障選線困難。分享友人