液性壓力 的英文怎麼說
中文拼音 [yèxìngyālì]
液性壓力
英文
press of fluidity-
In this paper a kind of cardio - cerebral arterial bifurcation vessel hemodynamic characteristics are studied with the boundary element method, and the blood flowing velocity vector distributions have been calculated. in addition, the flow field distribution and the pressure on the particle surface are also calculated, when there is flow - round particle at the place of bifurcation, the move tendency of the particle is judged, the possible reasons of causing the atherosclerosis, thrombus, angioma are analysed
本文用邊界元方法研究了一類典型心腦動脈分支血管中血液流動的流體動力特性，計算了分支血管血液流動的速度矢量分佈，同時計算了分支附近有多個顆粒狀繞流物時血液的流場分佈，及顆粒物所受壓力狀況，給出了顆粒物的運動趨勢，分析了引起粥樣斑塊病變、血瘤、血栓的可能原因Fluid noise mainly comes from out put pulsation of rate of flow, the main reason of out put pulsation of rate of flow is the instant high pressure return flow that obturation cubage produced when the big round curve pressure transition. the v trough on the port plate can reduce the fluid noise. in this paper, the author based on the acting of dam a river and condensability of liquid and used matlab language as tool to calculate the v trough on the original port plate and drew out the p - t diagrammatic curve and analyzed its shortcoming and improved the design of original v trough and got that the best size of its angle was 12. 3 and its length was 5mm and the cross section was an equilateral triangle
流體噪聲主要來源於輸出流量脈動，造成輸出流量脈動的主要原因是閉死容積在大圓弧段壓力切換時產生的瞬時高壓迴流，在配流盤上開設v型尖槽可降低因高壓迴流而引起的流體噪聲，本文以截流作用和液體的可壓縮性為理論依據，以matlab語言為工具，對原配流盤上的v型尖槽進行了理論計算，繪制出p - t圖線，分析了它的不足，並對原有v型尖槽進行了優化設計，得出了v型尖槽的最佳幾何尺寸：配流盤平面上的v型尖槽的兩邊的夾角為12 . 3 ，槽長5mm ，槽的橫截面為等邊三角形。Applicable to lpressure measurements for liquid mediums at high temperature, such as corrosive, high viscous, crystallizable and solid - particles containing fluids commonly used in petrochemical indusery, etc
隔膜壓力表用於化工等部門生產過程中測量具有腐蝕性、高粘度、易結晶、含有固體狀顆粒、溫度較高的液體介質的壓力。Through the special studies on impacts to atomizing and humidifying effect from such factors as the firing pin type, centrifugal structure, higher spraying pressure, less aperture, initial water temperature and original state of the air, some conclusions are obtained, such as : the centrifugal nozzle with firing pin type, high pressure and little aperture has bigger air eddy and atomizing angle. the spaying liquid has high velocity. the droplet is small, and the heat and mass transfer velocity is high
通過對撞針型結構、離心式結構、較高的噴水壓力、較小的噴嘴孔徑、噴水初溫及待加濕空氣初狀態對霧化加濕效果的作用原理的重點分析，得到：撞針型高壓小孔徑離心式噴嘴具有較大的空氣渦與霧化角，噴出的液體流速高、液滴小、水與空氣傳熱傳質速率高，撞針型結構提高了霧化加濕效率，高壓小孔徑的特點為霧化加濕提供了較大的能量，而噴水初溫的升高會減小水的粘性力和表面張力，從而優化加濕效果。Based on the close analysis of the influence factors of the vertical bearing capacity, circular aperture extension theory is employed to establish the computing formulas for the pile vertical stress and the foundation vertical bearing capacity, respectively. moreover, with analyzing the features of the calculation parameters such as materials of gunite mortar, jet pressure, diameter of the jet pipe, pile length, pile layout, a design theory for chemical churning pile composite foundation is proposed. then, the variation of the pipe deformation with loads, the deformation coordination of pile and soil are studied
在此基礎上深入探討了旋噴樁的樁土受力特性及其復合地基的加固機理，從影響旋噴樁復合地基豎向承載力的因素入手，基於圓孔擴張理論給出了樁體豎向應力及旋噴樁復合地基的豎向承載力計算公式;通過對噴射漿液、噴射壓力選取、噴射直徑估算、樁長及樁位設計等各種計算參數的深入分析和研究，提出了一套相應的旋噴樁復合地基設計計算方法;通過計算分析，深入探討了旋噴樁復合地基變形隨荷載變化規律、樁和樁間土變形協調關系、樁土應力比及復合地基壓縮模量的確定，並提出相應的設計方法和修正參數;此外，結合工程應用，對旋噴樁復合地基的施工技術及其現場質量檢測方法進行了較全面的探討。In pumping fluid with gas, pressure boost can be improved by enhancing the pump rotation speed, thereby improving the performance of the pump to a certain degree ; when the gas content is constant, by increasing the inlet pressure, the pressure boost can be enhanced and the pump efficiency be improved remarkably ; when the gas content is rather high, there will be a problem of matching between the gas pressure and the fluid pressure ; the performance of the multiphase pump can also be improved by means of rational design of buffer vessel and homogenizer
試驗分析認為，氣液混輸工況下，提高泵轉速可以提高增壓，在一定程度上能改善多相泵的工作性能；含氣率一定時，增加進口壓力，可使多相泵增壓值增大，泵效明顯增加，最大含氣率點后移，但含氣率很高時，存在氣液壓力相匹配問題；改進緩沖罐和均化器的設計，有利於氣液互相夾帶，避免氣囊產生，可改善多相泵的輸送性能。Modbus transducer is the key device in the system and is used to offer power supply of pressure and temperature sensor, to collect signal, to linearizate and compensate temperature, to calculate density, volume and mass, to transmit data to modbus network, and display the data. so the modbus transducer is a multi - parament measurement, intelligent control device which can manage multi - signal
變送器是系統的核心設備，其作用是為油罐溫度、壓力、液位、可燃氣濃度等傳感器供電，採集傳感器信號並進行線性化、溫度補償等處理，完成密度、體積和質量等參數計算，將數據輸出到modbus現場總線測控網路，根據需要現場顯示計測量參數。A lot of experiments have been done in the process of exploiture soft packaging li - ion battery about how to choice the rational arts and crafts. the content include : how to deal with the collector, add how much pvdf in the material, how long the material need to stirring and the right viscidity, how much condubtivity agent the electrode need, what theckness is best, choice different collectors, the degree of dryness of the electrode, theckness of pressed model, how much electrolyte will be added, placement how long after added the electrolyte, system of formation how to influnce the battery, in formation the battery need or not need preesure from outside, how to vacuumize and the optimize matching positive pole and negative pole. with these practice make sure the parameter of the positive pole should less than 90 m ; according to different vacuumize order the conduc - tivity agent in anode will be 5mass % and 9mass %, respectively, and in cathode the data is 2mass % ; every 100mah added to 0. 4 ml electrolyte ; before formation the battery should be placement 8 hours and the system of formation must be less than 0. 01c before the voltage reach to 3. 0v ; should press in outside when battery in formation ; to these batteries which capacity more than 350mah the vacuum time not excess 15s ; the optimize matching positive pole and negative pole between 2. 10 : 1 and 2. 15 : 1. finally make out the battery which cycling performance and security are all very well
液態軟包裝鋰離子電池的研究主要是對關鍵工藝進行了優化設計，具體包括:集流體的處理、 pvdf的加入量、漿料攪拌時間和粘度、導電劑的加入量、電極膜的厚度、不同集流體的選擇、電極膜的乾燥程度、壓型的厚度、電解液的加入量、注入電解液后靜置時間的長短、化成制度的影響、化成時電池所具有的壓力影響、抽真空的處理、正負極活性物質的匹配。最後確定出液態軟包裝鋰離子電池最佳工藝參數:正極膜的厚度小於90 m ;根據化成時不同抽真空順序，確定正極膜中的導電劑的加入量分別為5mass %和9mass % ;負極膜中導電劑的加入量為2mass % ;電解液的加入量為每100mah添加0 . 4ml ;化成前電池的靜置時間應當大於8h ;電池在3 . 0v之前採用小於0 . 01c的化成制度;在化成過程中應當施加一定的外部壓力;對於350mah的電池抽真空的延時不應大於15s ;而正負極活性物質的質量比應當在2 . 1 : 1 2 . 15 : 1之間。Dependence of the properties of pes hollow fiber on the pressure of internal quench medium
填充液壓力對聚醚碸中空纖維膜微結構和性能的影響When tlp bonding with proper pressure, the oxidation on the surface of al mmcs was n ' t the primary effect of the properties of the joint
採用適當的壓力進行瞬間液相連接時，鋁基復合材料表面的氧化膜已不是影響接頭性能的主要因素。They generally arise when a continuous pressure differential allows blood to flow constantly from a high to a low pressure area, as may occur in a variety of congenital defects, most commonly patent ductus arteriosus, anomalous origin of the left coronary artery, or coronary arteriovenous fistula
一般出現在持續壓力差使血液從一高壓區不斷流向低壓區時，也可以出現在一些有先天性缺陷的病，最常見的有動脈導管未閉、左冠狀動脈起端異常，或冠狀靜脈動脈瘺。On the basis of the characteristic of the industry waste slag, which is high added to the hsfab, different kinds of catalyzing methods are adopted to make the waste residue more active. the additive f, developed by the author can obviously improve the mechanics characteristic and durability of hsfab, especially the restraining of the drying shrinkage. based on the study of technics parameters and the problems in the manufacture, hf - 1100 series full - automatic hydraulic pressure wall brick presses is chosed to solve the problems, such as low molding pressure, low efficiency and the certified product ration
在hsfab的研究方面，通過兩種體系hsfab （即「水泥?鋼渣?粉煤灰?爐渣」和「石灰?鋼渣?粉煤灰?爐渣」體系）的配方優化設計，使之具有良好的社會、經濟和環境效益；在高摻量工業廢渣的前提下，根據各種原料的特性，對其採用不同的活化技術，使其具有較高的活性；自研的外加劑f ，對hsfab製品的物理力學性能和耐久性能均有明顯的改善作用，尤其是對製品的乾燥收縮性能有顯著的抑制作用；通過對工藝參數的研究，結合實際生產普遍存在的問題，選取了hf - 1100系列全自動液壓墻體磚壓機，有效地解決了傳統制磚過程中常見的成型壓力低、生產效率低、產品合格率低（即「三低」現象）等問題。Intelligent multi - channel data - logging display controller adopt advanced microprocessor for smart control, it is suitable for display and control temperature, humidity, pressure, liquid level, instantaneous flow, speed and so on in many physical quantity inspect signal, and can data - logging multi - channel measure signal. it also can carry on high - accuracy linear correction to various non - linear input signals
雙迴路數字光柱顯示控制儀採用先進的微處理器進行智能控制，適用於溫度濕度壓力液位瞬時流量速度等多種物理量檢測信號的顯示及控制，並能對各種非線性輸入信號進行高精度的線性校正。In this paper, the sensibility analysis of the factors affecting the temperature in well bore is relatively systematically made by using a large number of the data calculated with the borehole flow and heat transfer 3 ? d numerical model proposed by the author. the study shows that the thermophysical parameters of the drilling fluid and formation, etc. and the entrance temperature and circulating capacity, etc. of drilling fluid have a greater influence on the temperature in well bore. therefore, accurately mastering the thermophysical parameter values of penetrated formation and drilling fluid in well bore, considering the influence of the temperature and pressure on thermophysical parameters and accurately measuring such parameters as entrance temperature and discharge capacity of drilling fluid, etc. are of utmost importance for accurately simulating the temperature in well bore
利用由作者提出的井內流動和傳熱的三維數值模型計算所得的大量數據，文章對影響井內溫度的諸多因素進行了較系統的敏感性分析，研究表明：鉆井液和地層等的熱物理參數以及鉆井液的入口溫度、循環排量等對井內溫度有較大影響，因此，準確掌握所鉆地區地層和井內鉆井液的熱物理參數值，考慮溫度壓力對熱物理參數的影響，準確測量鉆井液的入口溫度、排量等參數值，對于井內溫度的準確模擬至關重要。Laser, ultrasonic beam and microwave are used in non contacting level measuring systems. laser systems suffer from dirt, ultrasonic sensors are strongly affected by changes of the velocity of sound and usually a pipe is needed to couple the ultrasonic waves into the liquid tank, which is difficult when there is a high pressure or when explosion protection is necessary
壓力式液位測量系統原理簡單、成本低，但測量精度和應用場合有一定的局限性，超聲液位儀精度較高，但設備復雜，一般需要用導管將超聲波傳到被測的液體中，因而安裝維護較麻煩，激光測距系統對環境要求嚴格。The results show that, comparing with the gas pressure drops calculated by the modified ergun equation, in the cases of the gas reynolds number is small, due to the presence of the dead space, the observed p in the experiments are bigger than that obtained by calculation, and when the gas reynolds number is large, because of the small interfacial viscous drag - force between gas and liquid, the p observed are smaller than that obtained by calculation
結果表明在氣相雷諾數較小時，由於停滯孔隙率的存在，實測壓降值比修正厄根方程計算的值大；氣相雷諾數較大時，氣液界面上產生的粘性曳力較小，實測壓降值比修正厄根方程計算的值小。The regulating characteristics of hydraulic control pressure in at automatic transmmission
自動變速器液控壓力的調節特性Speedfast enterprises limited was established in 1980 introducing lubricants, various industrial lubricating oils, fire resistant hydraulic fluid, etc. to hong kong s die - casting industry, which was newly - developing at that
潤滑劑、工業潤滑油、防燃性壓力液等等，致力服務業界，提升工業安全及生產能力，提高產Pump oils, fire resistant hydraulic fluid, mould releasing fluid for ( zinc, aluminium, copper or magnesium alloys ) die - casting, plunger lubricants, liquid paraffin, food grade lubricants, cutting fluid, grinding fluid, lubricating
性壓力液、 （鋅、鋁、銅、鎂合金）壓鑄脫模劑、沖頭油、乾性潤滑珠和粉劑、食品機械潤滑Combining physical experiments and theoretical analysis, this literature has performed thorough research on gas properties of delivery pipeline system, pressure current rush to interception air - mass in pressure pipeline, water hammer with gas that happens with gas releasing and liquid column separating
本論文通過物理試驗與理論分析對輸水管道系統中的氣體特性、壓力水流沖擊截留氣團和包含氣體釋放和液柱分離現象的含氣水錘進行了深入研究。分享友人