液態塑料 的英文怎麼說
中文拼音 [yètàisùliào]
液態塑料
英文
liquid plastic-
Test method for stress crazing of acrylic plastics in contact with liquid or semi - liquid compounds
丙烯塑料在與液態或半液態化合物接觸中產生的應力裂紋的試驗方法Study on the mechanism of void formation in roto - moulding of long - fiber reinforced resin
長纖維增強液態反應性樹脂復合材料旋轉模塑成型工藝氣泡形成機理試驗分析On the saturate concentration, the moisture density in the micro - holes was 100 times larger than the vapor density in the standard state, but only 8 % of liquid water. the water inside the plastic material was in a special liquid state. the delamination and the delamination recovery were observed by c - sam
當水汽濃度達到飽和時,在塑封材料中可以被水分子進入的有效體積內,實驗條件下的水汽密度為標準狀態下水蒸氣密度的100倍,為液態水密度的8 ,表明在塑封材料中的水分子以一種特殊的液態水形態存在。Plastics. solid or liquid unpolymerized epoxy resins. determination of volatile matter
塑料製品.固態或液態未聚合的環氧樹脂.揮發物質的測定The liquid infiltration - extrusion technology, as a new forming method which includes the liquid forging and the solid extrusion, has been developed in recent years. the process in essence is that after liquid metal is infiltrated into the fiber perform under pressure, high pressure is directly applied to it so that the melted metal is to be crystallized and solidified under pressure, and then undergoes large plastic deformation at the liquid - solid state or the state just solidified
液態浸滲擠壓是近年來發展起來的一種融液態模鍛和固態擠壓為一體的新成形工藝,其工藝實質是使液態基體金屬在壓力下滲入纖維預制體中,發生壓力下結晶凝固,並在液-固態或剛凝固態經受大的擠壓塑性變形,一次成形出金屬基復合材料的型材類製件。Plastics. liquid resins. determination of density by the pyknometer method
塑料製品.液態樹脂.用比重計法測定比重Plastics - liquid resins - determination of density by the pyknometer method iso 1675 : 1985 ; german version en iso 1675 : 1998
塑料.液態樹脂.用比重計法測定濃度Plastics. liquid and solid phenolic resins. measurement of density
塑料製品.液態和固態酚樹脂.密度的測量Rubber and plastics hose and hose assemblies with wire reinforcements ; hydraulic impulse test with flexing iso 6802 : 1991 ; german version en 26802 : 1993
金屬絲增強的橡膠和塑料軟管組件.撓曲狀態下液壓脈沖Liquid composite molding ( lcm ) is a close operation whereby a dry preform is placed between matched moulds and impregnated with a liquid resin
復合材料液體模塑成型技術( liquidcompositemolding ,簡稱lcm )是指用液態樹脂直接浸潤模腔中的纖維預成型體進行成型的一類工藝。Plastics - smoke generation - determination of the corrosivity of fire effluents - dynamic decomposition method using a travelling furnace
塑料製品.煙霧生成.滅火廢液腐蝕性的測定.第3部分:採用移動式熔爐的動態分解法Dual material tanks for underground storage of liquid petroleum products. steel exterior tank. plastic interior tank
液態石油產品二類地下貯存用混合式貯罐.金屬外貯罐.塑料內貯罐The material relies on two substances : liquid dicyclopentadiene, a common ingredient of plastics, and a catalyst ( the researchers & acute ; proprietary secret ) that causes dicyclopentadiene to harden
這種材料依賴兩種物質:液態二環戊二烯和一種催化劑。前者是塑料的普通成分,後者則是研究者的專利秘密,可以使二環戊烯變硬。Mould board cabinet - type support base integral strcture, small diameter of screw bar with large length against diameter ratio, full computer dynamping color display temperature tuzzy controlling, imported hydraulic electrical devices, tine mould clamping rigidity, high precidion of injection, it is suitable for injection with engineering plastics
模板箱式支座連體結構,螺桿小直徑、大長徑比,全電腦動態彩色循環顯示,溫度模糊控制,進口液壓電氣配置,整機合模剛性好,注射精度高,適合工程塑料製品注塑成型。Gummimueller gmbh offers you pertinent information by telephone for the ranges liquid plastics, hoses and special construction in addition to building of ponds. contact gummimueller gmbh
Gummimueller gmbh是一家高級企業,該企業使用多種工藝製造液態塑料,軟管、套管,特種產品,蓄水池建造。Plastics. polymers resins in the liquid state or as emulsions or dispersions. determination of viscosity using a rotational viscometer with defined shear rate
塑料製品.液態或乳濁態或分散態聚合物樹脂.用確定的剪切速率旋轉粘度計測量粘度Plastics - polymers resins in the liquid state or as emulsions or dispersions - determination of viscosity using a rotational viscometer with defined shear rate iso 3219 : 1993 ; german version en iso 3219 : 1994
塑料製品.液態或乳液或漂移的聚合物樹脂.使用規定剪New steel tanks with reinforced plastic lining for storing liquid petroleum products
液態石油產品貯存用帶增強塑料襯里的鋼制新貯罐Operational steel tanks with reinforced plastic lining for storage of liquid petroleum products
液態石油產品貯存用帶增強塑料襯里的鋼制舊貯罐分享友人