液溶膠 的英文怎麼說

中文拼音 [yèróngjiāo]
液溶膠 英文
lyosol
  • 液 : 名詞（液體） liquid; fluid; juice
  • 溶 : 動詞（溶化; 溶解） dissolve
  • 膠 : Ⅰ名詞1 （某些具有黏性的物質） glue; gum 2 （橡膠） rubber 3 （姓氏） a surname Ⅱ動詞（用膠粘） st...
  1. ( 2 ) in ( no3 ) 3 was dissolved in acetylacetone in the mol ratio of l : 3. they were mixed for about 3 hours to obtain acetylacetone salts. then glycol methyl aether was added in the ratio of 1 : 40 to obtain indium oxide sol. sncl4 was dissolved in glycol methyl aether and then added into the indium oxide sol to prepare transparent and stable ito sol

    （ 2 ）通過將銦的無機鹽硝酸銦與乙酰丙酮按摩爾比1 ： 3 ，混合攪拌3h左右得到銦的乙酰丙酮鹽，然後按一定摩爾比加入乙二醇獨甲醚溶液，混合攪拌制得氧化銦溶膠，再將一定量的sncl _ 4溶入乙二醇獨甲醚，摻入氧化銦溶膠制得透明穩定的摻錫氧化銦溶膠（ ito溶膠） ，該溶膠性能穩定，易於成膜。
  2. A sol that consists of solid particles suspended in a liquid is a colloidal suspension.

    由固體微粒懸浮在液體中所組成的溶膠叫膠態懸浮體。
  3. Only small total volumes of liquid aerosols can be expected to reach the distal portions of the tracheobronchial tree.

    只有很少一部分液狀氣溶膠可達到細末支氣管。
  4. Study on nano - tio2 sol in ethylene glycol

    乙二醇溶膠溶液的研究
  5. The obtained biosensor exhibits high sensitivity, excellent reproductivity and good stability with substantially improved performance. part two describes the manufacture and characterization of glucose oxidase - silver sol - polyvinyl butyral modified platinum electrodes with tris ( 2, 2 ' - bipyridyl ) cobalt ( iii ) perchlorate as an electron transfer mediator in the glucose solution

    用納米ag溶膠固定god ，採用聚乙烯醇縮丁醛為輔助固酶膜基質修飾鉑絲電極，並以葡萄糖溶液中的co恤pyh （ cio4 ） 3為電子媒介體組成葡萄糖氧化酶生物傳感器。
  6. It is shown that the liquid phase methods, in which particularly methods of the sol - gel, deposition, micro - lacteous, hydrothermal / solvothermal reaction and hydrolyze, should be mentioned, as the most wildly used method in the present

    指出液相法，尤其是溶膠凝膠法、沉澱法、水解法、微乳液法、水熱溶劑熱法等是目前制備納米金屬氧化物材料最廣泛應用的方法。
  7. Paohuajian, guirongjiao production sales ; ye jian, cast steel, vulcanized alkali, coal, guisha, bentonite, jianshuiji, paper, subian, fire - proof material in the wholesale and retail

    泡花堿、硅溶膠的生產銷售；液堿、鑄鋼、硫化堿、煤炭、硅砂、膨潤土、減水劑、紙張、塑編、耐火材料的批發零售。
  8. The urea - formaldehyde ( uf ) polymer / sio2 composite microspheres were prepared by polymerization - induced colloid aggregation ( pica ) method. the formation mechanism of composite microspheres is attributed to the fact that that urea and formaldehyde firstly undergo acid - catalyzed polymerization to form oligomers, and then the sol particles are adsorbed on the chain of oligomers by wan der walls force and hydrogen bonding. when the oligomers reach the critical chain length, they separate from solution due to phase separation

    對復合微球形成機理的研究表明，尿素和甲醛在酸性條件下自身聚合可以形成高分子微球，在sio _ 2酸性溶膠中發生聚和反應時，隨著反應的進行，齊聚物不斷生成， sio _ 2膠體顆粒逐漸吸附在齊聚物分子鏈上，當聚合物鏈達到沉澱臨界鏈長時，由於相分離作用，從前驅物溶液中析出，同時sio _ 2膠體顆粒均勻的分佈在脲醛聚合物網路中，隨之沉澱出來，形成脲醛sio _ 2復合微球。
  9. With the reference of many relevant materials, the author prepared a fined molybdenum disulfide powder with a average size of 800nm by ball milling, and a nano - copper with average size of 30nm in micromulsion solution method, and synthesized surface - modified titanium dioxide nanoparticles with average size of 40nm in organic media via sol - gel method. the tribological performances of three particles were studied by universal test as well, with the result of fined molybdenum disulfide powder with good reducing wear and antiwear performance at low load, nano - copper with good reducing wear and antiwear performance at high load, surface - modified titanium dioxide nanoparticles maintaining stable reducing wear and antiwear performance from low load to high load due to its characteristics of organic and inorganic nanocomposite. the results indicate that the nanocomposite is the most perspective oil additive. the reducing wear and antiwear mechanism of nano oil additive was studied with in - situ tribochemical principle. nano additives possess broadly developing prospect with its above - mentioned performance

    在參閱了大量文獻的基礎上，分別採用了球磨法、微乳液法、溶膠?凝膠法制備了超細二硫化鉬、納米銅粒子、表面修飾納米二氧化鈦，經原子力顯微鏡測試，獲得的超細二硫化鉬的粒度平均在800nm以內，納米銅粒子平均粒度約為30nm ，表面修飾納米二氧化鈦平均粒度約為40nm ，在萬能摩擦磨損試驗機上測試了三種粒子的摩擦學特性，結果表明：在合理的添加濃度范圍內，超細二硫化鉬在低載時具有優良的減摩抗磨性能，納米銅在高載時具有比較好的減摩抗磨性能，表面修飾二氧化鈦粒子因具有有機與無機復合物的特性，從低載到高載都保持穩定的減摩抗磨性能。
  10. In this study we adopt a novel coordination - gel method to prepare zro2 - ni nanocrystalline composite powder. compared to the traditional methods such as coprecipitation, combusting solution synthesis and sol - gel method, coordination - gel method avoids the disadvantages such as bad uniformity of phases " buildup and difficulty of controlling the craftwork

    本文採用一種新的絡合-凝膠法制備zro _ 2 - ni納米復合粉末，與傳統的共沉澱法、溶液燃燒合成法、溶膠-凝膠法相比，絡合-凝膠法克服了其它制備方法中金屬相和陶瓷相分佈不均、工藝難以控制的缺點。
  11. Water - or solvent - soluble liquid adhesives for automatic machine sealing of top flaps of fiberboard shipping cases

    纖維板船運箱頂蓋自動機密封用水可溶或溶劑可溶的液體膠粘劑
  12. The fluorescence intensity of tb observed in pt / tb sol was stronger than that in powders. the network made of o, ti, such as sol and noncrystalline powders, determined the fluorescence intensity of pb

    Pb離子的熒光與pb所處環境相關，既可出現在液相體系，又可出現在固相粉末體系中，也即處于o ， ti等離子構成的無規則網路結構狀態下的溶膠、凝膠或非晶固態時。
  13. Standard test method for metal removal fluid aerosol in workplace atmospheres

    工作場所大氣中金屬切削液氣溶膠的標準試驗方法
  14. The preparing process is as follow : mixing the nickel salt, zirconium salt and stabilizer in the solvent ( distilled water ) to prepare mixing solution according to a certain ratio ; commingling the mixing solution and coordination solution of carboxylic ammonia in accordance with a certain rate to form sol, drying the sol and turning it into gel, pre - sintering the gel to get the zro2 - nio powders and the zro2 - ni nanocrystalline composite powders were gained by reducing the zro2 - nio powders

    方法如下：將鎳鹽、鋯鹽、穩定劑和水溶劑按所需成分配成混和溶液，再將混和溶液、外加劑按比例混和形成溶膠，溶膠經乾燥成為凝膠，凝膠經預燒得到ysz - nio氧化物納米粉末，將該氧化物粉術還原得到ysz - ni納米復合粉術。絡合。
  15. In this study, the preparing processes of zro2 - ni nanocrystalline composite powder aremixing the nickel salt, zirconium salt and stabilizer, solvent ( distilled water ) together to prepare the mixing solution according to certain ratio ; commingling the mixing solution, coordination solution of carboxylic ammonia, intrusion aid in accordance with certain rate to form sol, drying the sol and turning it into gel, pre - sintering the gel to get the zro2 - nio powder and gaining zro2 - ni nanocrystalline composite powder by reducing the zro2 - nio powder. xrd, x - ray wide - angle diffractometer, bet, sem, tem, hrtem analyses are used to study the zro2 - ni nanocrystalline composite powder and zro2 - ni cermet. the sintering temperature is determined

    本研究的zro _ 2 - ni納米復合粉末的制備方法如下：將鎳鹽、鋯鹽、穩定劑和溶劑（水）按所需成分配成混合溶液，再將混合溶液、外加劑和氨羧絡合劑按比例混合形成溶膠，溶膠經乾燥成為凝膠，凝膠經預燒得到zro _ 2 - nio納米粉，將該氧化物粉還原得到zro _ 2 - ni納米復合粉。
  16. In this paper, the optimum conditions of catalyst preparation were found by studying the influences of the sol - gel process parameters on the crystal structure of the nanometer la1 - xsrxmno3, such as the value of original solution ph, the temperature of water bath, the baking temperature of sol

    本文研究了採用溶膠-凝膠法制備納米鈣鈦石型氧化物催化劑過程中，初始溶液ph值、水浴溫度、焙燒溫度對納米la1 - xsrxmno3晶體結構影響。
  17. Life time of mn2 + in nano - zns was measured and was found to be close to that of the bulk materials. therefore the quenching centers quench the exciton but not the mn2 + ion self. 2. the increasing curves are different in film and ethanol colloids because there is diffusion process of quenching centers in colloids

    對薄膜樣品的熒光增強曲線的擬合表明，顆粒表面猝滅中心數目隨輻照時間的衰減函數是非e指數形式;同時考慮溶液中猝滅中心通過向顆粒表面的擴散而逐漸耗盡，很好地解釋了溶膠的增強曲線與固體薄膜的增強曲線的不同。
  18. In this process, sncl4 solution is added and react with nh3 h2o under the use of ultrasonic wave, controlling the acidity ph, reaction time and temperature and the sol can be got

    一定濃度的sncl _ 4溶液在超聲波作用下與nh _ 3 ? h _ 2o進行反應。控制一定的ph值，反應溫度和時間，形成穩定的溶膠體系。
  19. Abstract : the technical characteristics, research status and recent progress in preparing nanometer particles by liquid - phase synthesis including precipitation, solvent evapration, hydrothermal, sol - gel and microemulsion technigues have been reviewed in the paper

    文摘:論述了目前常用的液相合成技術（包括沉澱法、溶劑蒸發法、水熱法、溶膠-凝膠法和微乳液法）制備納米顆粒的技術特點、研究現狀及其進展。
  20. The bzt thin film has good properties in high frequency. the essential principle, technology process and advantages of the ba ( zr0. 3ti0. 7 ) o3 ( bzt ) ferroelectric thin films grown on pt / ti / sio2 / si substrates and quartz substrates by sol - gel process are introduced. the heat - treatment technology was fixed according to the dsc - tg measurement, afm ( atomic force microscope ) and fe - sem ( field emission - scanning electrical microscope )

    我們通過在pt / ti / sio2 / si襯底和石英襯底上制備ba （ zr0 . 3ti0 . 7 ） o3鐵電薄膜，了解了溶膠-凝膠法（ sol - gel ）制備薄膜的基本原理、工藝過程及工藝特點;並對所制得的ba （ zr0 . 3ti0 . 7 ） o3薄膜的前驅體溶液和干凝膠進行了差熱與熱失重（ dsc - tg ）分析，確定了溶膠在熱處理各個階段的反應情況。
分享友人
分享到 Line

分享到臉書