液體壓頭 的英文怎麼說
中文拼音 [yètǐyātóu]
液體壓頭
英文
liquid head-
In the course of working, , the plow will make use of the shuttling method so that it can dig alternately either on the left or on the right. compared to the unilateral plow, it can improve the productivity because it can help leave off the soil 、 take from the consumed energy and reduce the empty journey. to meet the requests above, we will use a remote cylinder with both a small cubage and double functions, approximately designing the plow to be columniform and symmetric. after the experiment for a period in the field, we found that the most frayed areas had happened at the places of both plow shank and share and at the same time the base of the remote cylinder had ruptured suddenly
與單向犁相比,其優點在於:耕地無開、閉壟,地表平整,降低了耕后整地的能量消耗,減少了地頭的空行程,因而大大提高班次生產率。為了滿足犁體梭式作業的要求,我們採用了一隻小容積雙作用的液壓油缸;同時對犁壁曲面的形狀採用了近似圓柱形的對稱設計。但經過一段時間的田間試驗,我們發現:該犁犁胸部分的犁脛和犁鏵上的犁尖在工作中磨損較為嚴重;主犁梁和油缸缸體的連接部分(即油缸底座)突然發生了斷裂,造成整個犁體無法正常工作。This ultrafilter adopts dissymmetrical semipermeable film which is made from macromolecule material with special process, the raw liquid flows under pressure, inside or out side the film, the macromolecule substance and colloid particles in the raw liquid are clogged at the film suface and are brought away by circulating raw liquid. then the raw liquid becomes inspissated, and further more, the substance in liquid is separated
本設備是以高分子材料採用特殊工藝製成的不對稱頭透膜,在壓力作用下,原液在膜內或膜外流動,其中的高分子物質,以及膠體粒子則被阻止在膜面,被循環流動的原料帶走而成為濃縮液,從而達到了物料的分離濃縮和提純的目的。This ultrafilter adopts dissymmetrieal semipermeable film which is made from macromolecule material with special process the raw liquid fiows under pressure , inside or out side the film the mscromolecule substance and colloid particles in the raw liquid are clogged at the film suface and are brought away by circulating raw liquid then the raw liquid becomes inspissated , and further more , the subtance in liquid is seperated
本設備是以高分子材料採用特殊工藝製成的不對稱頭透膜,在壓力作用下,原液在膜內或膜外流動,其中的高分子物質,以及膠體粒子則被阻止在膜面,被縮和提純的目的。This ultrafilter adopts dissymmetrieal semipermeable film which is made from macromolecule material with special process. the raw liquid flows under pressure, inside out side the film suface and are brought away by circulating raw liquid. then the raw liquid becomes inspissated, and further more, the subtance in liquid is seperated
本設備是以高分子材料採用特殊工藝製成的不對稱頭透膜,在壓力作用下,原頁在膜內或膜外流動,其中的高分子物質,以及膠體粒子則被阻止在膜面,被循環流動的原料帶走而成為濃縮液,從而達到了物料的分離濃縮和提純的目的。Geng ventebra is the supply of human body brain department blood biggest hub, pawn geng ventebra appearance patient, scondition can anise headache, migraine, heart disease, hypertension and siabetes adopt vanious famous and precious ptant through professional skill, alleviate to aim at gebg vertebra strain stick out, shoylder jia scorching etc, case
頸椎是人體供應腦部血液最大軀紐,當頸椎出現病況會出現頭痛,篇頭通,心臟病,高血壓,糖尿病,採用多種名貴的精油配方,強力滲透進人體細胞,通過專業手法,緩解針對頸椎勞損突出,肩胛炎等情形。Reading methods of the vacuum gauges by means of the head difference in the hydrostatic pressure
通過液體靜壓力壓頭差讀取真空計的方法The sprayer is usually connected with water supply network, control value, detection alarm unit, etc. to form an automatic water spray system ( such as sprinkler fire - extinguishing system ) for saving electrical equipment, fighting burning flammable liquid, etc. it is widely used for fire control and cooling protection for such equipment / places as power plant * generating machinery, large size transformer, liquefied petrolatum tank, factory, shopping mall, hotel, warehouse, storied building and so on
該水霧噴頭通常與供水管網、控制閥門、控測報警器等組成自動噴水滅火系統(如雨淋噴水滅火系統等) ,用來撲救電氣設備,可燃液體火災等,廣泛用於保護電廠的發電設備,大型變壓器,液體石油儲罐、工廠、商場、賓館、倉庫、樓房等必須滅火、控火或防護冷卻等場所。According to these, the paper put forward some countermeasures : select low carbon steel or low metal alloy steel with lower intensity, like 20r steel ; while welding, adopt strict craft measures with lower welding heat to input ; after jointing, proceed the whole hot dissolving on time ; control each welding joint with hardness hb 185 ; add 0. 25 % water into the liquid ammonia as decay eclipse ; enhance checking in operation, repairing equipment in time through regular interior and exterior checking
針對上述原因提出了防止氨冷器類臨氨壓力容器產生應力腐蝕裂紋的對策:選用強度稍低,但抗裂性較好的低碳鋼和低合金鋼,如用20r鋼製造;焊接時應採用嚴格的工藝措施和較低的焊接熱輸入量;焊后應及時進行整體消除應力熱處理;控制焊接接頭各區硬度hb 185 ;在液氨中添加0 . 25 %的水作為緩蝕劑;在運行中加強檢查,及時進行停車檢修時的內外部檢查和定期檢驗。Connections for fluid power and general use - hydraulic couplings for diagnostic purposes - coupling with m16 x 2 end for connection under pressure
流體動力和通用連接器.診斷用液壓聯軸器.加壓連接用m16 2端頭Promptly shift oil / nls in the overflowed tank to an available empty of slack tank to relieve pressure in the overflowed tank
將溢流艙內的油或有毒液體物質轉移到空艙,以降低溢流艙內的壓頭。The liquor is pumped through a large nozzle and the velocity head is utilized to draw the gases to be absorbed into the liquid.
液體用泵送經一隻大的噴頭,利用速度變化產生的壓差將待吸收氣體帶到液體中。To ensure the charging pump working reliably, the following measures should be adopted : ( 1 ) adopting modified circular casing to reduce the radial force of the impeller and decrease the seal clearance ; ( 2 ) using radical ribs on impeller and helical sealing on shaft to realize minor pressure differential ; ( 3 ) using back pressure stuffing box to ensure sealing under small packing force ; ( 4 ) adopting self - lubricant flexible graphite stuffing for absorption of solids entering in the graphite in case of leaking
為確保灌注泵可靠工作,提出改進措施: ( 1 )採用改型環形泵體降低葉輪的徑向力,減小軸封間隙,抑制泄漏; ( 2 )採用背葉片降低葉片根部壓頭,獲得微壓,使軸封兩端承受較小壓差; ( 3 )採用螺旋密封降低軸封兩端壓差,在保持微壓的同時避免出現負壓,密封效果更好; ( 4 )採用反壓式填料密封結構,在很小的壓緊力下,即可保證密封; ( 5 )採用具有潤滑功效的柔性石墨填料,即使發生軸封泄漏,進入石墨內部的固相顆粒也將隨著石墨的消耗而被鉆井液吸收。Aimed at some problems such as short spraying distance, electricity - leaking and reverse ionization among electrostatic nozzles existing in the country, a induction charging and pneumatic energy electrostatic nozzle was designed. the basic designing theories, structure and working process of this nozzles were theoretically specified in the paper. and then the atomization quality and charge performances of this nozzle and its affecting factors were studied by carrying out performance experiment and statistic analysis. result of the studies indicate : ( 1 ) some progress were made in solving the problems list above ; ( 2 ) from this nozzle, droplet were minute and uniform, and higher charge - mass ratio can be obtained under lower electrostatic voltage, thus the atomization quality and charge performance of this nozzle were both better ; ( 3 ) within the experiment extend, air pressure at 0. 2mpa, electrostatic voltage at 2400v were the most suitable parameters for the nozzle ; ( 4 ) the regression equations for describing droplet size, intensity of spray current and charge - mass ratio of this nozzle obtained from the experiment data had higher forecast precision ; ( 5 ) cross - effect of all factors were not significant, the atomization quality and charge performance were relative dependency affected by the factors
諸試驗因素中,充電電壓和噴孔直徑對霧滴荷質比均有極顯著的影響;氣體壓力和液體流量對霧滴荷質比的影響均不顯著;影響霧滴荷質比的主要因素依次為充電電壓和噴孔直徑; ( 8 )在300v 、 600v 、 1200y 、 1800y 、 2400v 、 3000v六種充電電壓t ,霧滴荷質比先隨充電電壓的增加而增大, 2400v后荷質比減小,推測:對于所研製的噴頭可能存在一個最佳充電電壓; ( 9 )由充電電壓和噴孔直徑的不同搭配所得霧滴荷質比不同這一結果,可看出,較大充電電壓需配備較大噴孔直徑以增強霧滴荷電效果; ( 10 ) td3 . 6和td3 . 4兩噴頭的霧滴荷質比曲線趨于重合,說明噴孔直徑大於滬3We have many industry automize instruments such as temperature transmitter ( integrate temperature transmitter module ( double temperature transmitter module ), integrate temperature transmitter, track isolation temperature transmitter, hanging temperature transmitter, pressure transmitter ( expanding silicon pressure transmitter, sapphire pressure transmitter, spraying ( metal slim film ) pressure transmitter, strain pressure transmitter, ceramic resistor, capacitance pressure transmitter, 1151 and 3151 series pressure transmitter, fluid location transmitter module ( specializing for fluid location meter ), collocated electricity meter ( sigle round, double round ), signal isolation ( single round, double round ), transducer ( temperature, pressure ), display head ( showing 100 % scale, lcd fluid crystal, led digital display ), numerical instrument and so on
產品有溫度變送器(一體化溫度變送器模塊(雙支溫變模塊) 、一體化溫度變送器、導軌式隔離溫度變送器、壁掛式溫度變送器、架裝式溫度變送器) 、壓力變送器(擴散硅壓力變送器、藍寶石壓力變送器、濺射式(金屬薄膜)壓力變送器、應變式壓力變送器、陶瓷電阻、電容壓力變送器、 1151 、 3151系列壓力變送器) 、液位變送器模塊(專為液位計廠配套) 、配電器(單迴路、雙迴路) 、信號隔離器(單迴路、雙迴路) 、傳感器(溫度、壓力) 、配變送器的顯示表頭( 100刻度顯示、 lcd液晶顯示、 led數碼顯示) 、數字儀表等工業自動化儀器儀表。This charged fiber can be directed or accelerated by electrical forces and then collected in mats or other useful geometrical forms. the diameters of electrospun fibers are in the range of tens of nanometers to several micrometers. in this paper, polyacrylonitrile ( pan ) nanofibers are made by electrospinning pan / dimethylformamide ( dmf ) and pan / dimethylacetamide ( dmac ) with adjusting the main process parameters including electrostatic voltage ( 20 ~ 50kv ), sprinkler aperture ( 0. 5 ~ 0. 8mm ), collection distance ( 15 ~ 25cm ), solution concentration ( 6 wt % - 14 wt % )
本文主要對聚丙烯腈( pan )二甲基甲酰胺( dmf ) 、 pan二甲基已酰胺( dmac )體系進行電紡絲,調節靜電壓( 20 50kv ) 、噴頭孔徑( 0 . 5 0 . 8mm ) 、接收距離( 15 25cm ) 、溶液濃度( 6wt 14wt )等過程參數,制得pan納米纖維,纖維平均直徑在200 1000nm ;詳細分析了過程參數對纖維細度、形態等的影響,認為高聚物溶液濃度及靜電壓對纖維細度有決定性影響,其它過程參數如接收距離、噴射孔徑、紡絲溶液溫度、溶液電導率等的調整應以這兩參數為基礎進行。Methods of testing plastics - thermoplastics pipes, fittings and valves - thermoplastics pipes for the transport of liquids under pressure - calculation of head losses
塑料試驗方法.第11部分:熱塑性塑料管接頭和閥門.試驗方法1121h :非承壓液體輸送熱塑性塑料管.管頭損失計算For existing factories and warehouses and specialized depots and wharves for production, storage, loading and unloading of inflammable and explosive dangerous goods, and filling and loading stations, supply stations and pressure regulating stations for inflammable and explosive gas and liquid, in case they do not conform to the regulations of this article, relevant units shall adopt measures to give a solution within a time limit
原有的生產、儲存和裝卸易燃易爆危險物品的工廠、倉庫和專用車站、碼頭,易燃易爆氣體和液體的充裝站、供應站、調壓站,不符合前款規定的,有關單位應當採取措施,限期加以解決。I then felt a rush of what i can only describe as fluid running into my skull and a cracking sound as if pressure was being applied to the inside of my head
接著我感受到一股沖擊力,我只能形容它就象是液體沖入我的頭骨,並且還伴隨著破碎聲,就好象壓力被應用在我的頭里。Methods of testing plastics - thermoplastics pipes, fittings and valves - thermoplastics pipes, for the conveyance of fluids - resistance to internal pressure - test method
塑料試驗方法.第11部分:熱塑管,接頭和閥門.液體輸送用熱塑材管.試驗方法1127p :抗內壓力.試驗方法Abstract : this paper introduces the improving process of outside pour type hydraulic prop. it can reduce labour strength, raise pressure text safety and work efficiency
文摘:介紹了外注式單體液壓支柱試壓頭的改造過程,對其進行改進可以降低勞動強度,提高試壓安全性能和勞動效率。分享友人