渦輪導向葉片 的英文怎麼說
中文拼音 [guōlúndǎoxiàngyèpiān]
渦輪導向葉片
英文
nozzle guide vane- 渦 : 渦名詞1. (漩渦) eddy; whirlpool; vortex 2. (酒窩) dimple
- 輪 : Ⅰ名1 (輪子) wheel 2 (像輪子的東西) wheel like object; ring; disc 3 (輪船) steamer; steamboa...
- 導 : 動詞1. (引導) lead; guide 2. (傳導) transmit; conduct 3. (開導) instruct; teach; give guidance to
- 片 : 片構詞成分。
- 渦輪 : [機械工程] turbine; worm wheel渦輪泵 [航空] turbopump; roturbo; 渦輪發動機 turbine engine; 渦輪風...
-
Numerical simulation of leading edge film - cooling of turbine stator blades
氣膜冷卻渦輪導向葉片流場數值模擬By using harika algorithm, the characteristic of a high - pressure compressor is calculated at different installation angle of the inlet guide vane and the stator vanes ; the characteristics of a high - pressure turbine and a low - pressure turbine are simulated at different installation angles of the guide vane based on ainley method
本文用harika演算法計算了導流葉片和靜子葉片安裝角度可調的變幾何高壓壓氣機特性;用ainley法計算了渦輪導向器面積可調的高壓渦輪和低壓渦輪的特性。The vortex simulated in this article include the shedding vortex induced by the vane trailing edge boundary layer, the endwall vortex generated by the endwall boundary layer interaction, the passage vortex generated by the rotor rotation, and the leakage vortex generated by the tip clearance flow
渦輪級內的渦運動包括:導向器葉片尾緣附而層引起的脫落渦;轉子通道內轉子的旋轉運動產生的通道渦;根腳區兩個端壁附面層干涉,形成的根腳渦;存在葉尖漏流時,出現的漏流渦。Based on the the analysis of structure and design process of turbine blade, the normal design rules of turbine blade are presented in this paper which are realized by the way of the design wizard in the modeling system
本文詳細分析了渦輪葉片的結構和設計方法,在此基礎上總結了渦輪葉片的設計規范,並把此規范以設計向導的方式應用於系統中。Some of the air is used for cooling the turbine blades and nozzle guide vanes, and part of it is employed to cool and seal the turbine discs
在現代航空發動機中,從壓氣機引出的壓縮空氣一部分用來冷卻渦輪葉片和渦輪導向葉片,另外一部分用來冷卻和密封渦輪盤。Film cooling of the surface of a gas turbine blade was studied in a large - scale low - speed opening wind tunnel according to actual requirement of the design of aero - engine. the surface of a gas turbine blade was cooled by cylindrical holes in the experiment, with the hole number of fifteen in stator and eight in rotor
應航空發動機設計的要求,在大尺寸低速葉柵傳熱風洞中分別對發動機渦輪導向葉片和動葉表面的氣膜冷卻特性進行了研究,具體研究在不同氣膜孔出流時,在不同主流雷諾數和吹風比情況下葉片表面局部換熱系數的分佈規律。To satisfy the practical need of film cooling in turbine blades of aeroengine, some detailed experimental measurements on the flow field in the channel with the holes on the wall and in the holes had been completed within a wide range of aerodynamic parameters. and the interrelated numerical simulated compute had also been implemented
本文根據航空發動機中渦輪導向葉片氣膜冷卻的實際需要,在寬廣的氣流流動參數范圍內,對葉片內冷通道的流場進行了詳細的實驗測試,同時還進行了相應的數值模擬計算。分享友人