測角測距儀 的英文怎麼說

中文拼音 [cèjiǎocèjùyí]
測角測距儀 英文
apomecometer
  • 測 : 動詞1. （測量） survey; fathom; measure 2. （測度; 推測） conjecture; infer
  • 角 : 角Ⅰ名詞1 （牛、羊、 鹿等頭上長出的堅硬的東西） horn 2 （古時軍中吹的樂器） bugle; horn 3 （形狀像...
  • 距 : Ⅰ名詞1 （距離） distance 2 （雄雞、雉等的腿的後面突出像腳趾的部分） spur （of a cock etc ）Ⅱ動詞...
  • 儀 : 名詞1 （人的外表） appearance; bearing 2 （禮節; 儀式） ceremony; rite 3 （禮物）present; gift 4 ...
  • 測距儀 : ambulator
  • 測距 : range [distance] finding; distance measurement; ranging; stadiometry
  1. At present, the check standard of rotating laser has not come into being, and the manufacturers and users still use the traditional i angle method of gradienter which have long - distance, low precision and in the stage of eyeballing

    目前激光掃平儀檢定的專業標準尚未形成，生產廠家對激光掃平儀的檢測方法還在沿用傳統水準儀?角檢測法，檢測的距離大，檢測的精度較低，處於人工目視階段。
  2. The position and size of the monochromator, focusing curvature radii and tilting angles of the germanium focusing monochromator under different different take - off angle, size and divergency of the second collimator and intensity loss due to the use of it were determined. the neutron flux at different wavelength, under different reflection and take - off angle of the monochromator and divergency of the first collimator, were given. the simulation on the aperture used for limiting beam size in front of the sample showed that, smaller the size of the aperture and further the distance from the aperture to the sample, greater the loss of the intensity and more serious the spread of the beam along vertical direction at the sample position which makes the practical sampling volume greater than expected

    用蒙特卡羅模擬方法對中子應力衍射譜儀的設計方案進行了優化研究，提出了一系列可供參考的數據：確定了單色器的位置、尺寸、垂直聚焦單色器在不同起飛角下的聚焦曲率半徑和傾角；討論了第二準直器的尺寸和發散，以及使用第二準直器造成的強度損失；給出了在不同單色器反射面、起飛角、中子波長和第一準直器發散度的情況下樣品處的中子注量率，以及多種組合情況下譜儀的解析度曲線；對限束方孔的尺寸、距離樣品遠近對強度損失和測量中的影響做了深入研究。
  3. Analyze item by item the position of unintact cycle, the running clearance of unintact cycle, locking - deform, datum dimension regulating, repeatly install, power voltage wave and marking running etc. at the same time, we give the calculating formula to calculating the running marking random error, and use it to calculate the system error of big diameter measure instrument - - datum dimension frame error, gyro - wheel diameter error, error caused by circumstance temperature, error caused by backing distance, angle error, delay error of data collecting circuit, lathe main shaft running error, workpiece install partial error

    對不完整圓的位置、不完整圓的轉動間隙、鎖緊變形、基準尺調整、重復安裝、電源電壓波動、標記轉動等隨機誤差進行了逐項分析，並給出轉動標記隨機誤差的計算公式。對大直徑測量儀的系統誤差?基準尺尺架誤差、滾輪直徑誤差、環境溫度引起的誤差、後退距離引起的誤差、角度誤差、數據採集電路延時誤差、車床主軸回轉誤差、工件安裝偏心誤差分別進行了計算，最後對誤差進行合成。
  4. The autoaligment instrument and accuracy turntable with digital display are used to detect the step angle after 32 subdivision, and the experiment results are given, the mean - square error of step angle after 32 subdivision is less than 3. 7 %

    為了檢測32細分后的步距角，採用了自準直儀加精密數顯轉臺的光學測量方法，並給出了實驗結果， 32細分步距角的均方誤差不大於3 . 7 。
  5. The angular distance north or south of the earth ' s equator, measured in degrees along a meridian, as on a map or globe

    緯度地球赤道北或南的角距離，例如在地圖或地球儀上沿著子午線用度數測量
  6. So, a new criterion about the area calculation of the house appears. according to that, the area of the house equal to the sum of the practical area and the area of the wall section. the latter can be calculated on the criterion easily

    測量儀的測量房屋套內面積的設想是通過步進電機驅動激光測距傳感器旋轉每一步距角，對距離數據進行每步採集保存，轉滿一周后對相鄰距離值構成的三角形面積進行計算求和而得到面積。
  7. This is the latest development in our company - corner torque tester applies to automobiles, tractors, construction machinery and other wheeled vehicles to performance tests

    這是我公司最新研製多功能轉角扭距測試儀，適用於汽車、拖拉機、工程機械及其它輪式車輛的轉向性能測驗。
  8. The short - baseline interferometer system may obtain azimuth, distance and speed of the target, therefore the system may realize to two - dimensional localization of target

    短基線干涉儀系統可以測得目標的方位角、距離和速度，因此系統可以實現對目標的二維定位。
  9. This instrument was mainly used to measure the altitude of a celestial object above the horizon

    又叫地平緯儀，主要用於測定天體距離地平面的角度。
  10. Because the rangefinders you will use this on have viewfinders that are designed for the angle of view of 50mm lenses, you will need a special viewfinder to put in the accessory shoe in order to properly frame your subject

    由於測距儀你將使用這對有取景器，這種設計是為視角的50毫米隱形眼鏡，你會需要一種特殊的取景器投放配件鞋，以適當幀你的課題。
分享友人
分享到 Line

分享到臉書