溫熱強度 的英文怎麼說
中文拼音 [wēnrèqiángdù]
溫熱強度
英文
warm strength-
In this paper, using phoenics software to compute and analyze the variety rule of the convecting transfer heat at the basis of computing and analyzing the temperature and velocity field of one underfloor supply air room with a focus hot source, and concluding that the number of the hot source and the supply air outlet > the intensity of the hot source and the volume of supply air will influence convecting transfer heat, and obtained its correlativity formula
本文針對一下部有集中熱源的地板送風空調小室,利用phoenics軟體,在計算分析小室內氣流的速度場及溫度場的基礎上,對對流熱轉移量的變化規律做了計算分析,最後得出對于下送風小室的對流熱轉移量與熱源的個數、送風口個數、熱源強度、送風量等因素有關,並且得出了其相關關系式。And due to the heat expansile coefficient of the stainless steel rather high, the connecting force between the stainless steel pipe and the pipe coupling in the room temperature is much less than that between the titanium alloy pipe and the pipe coupling. the results accord with the tensile experiments well. finally, the dependence of dimensions of the coupling on the strength of the connector system is analyzed
模型計算還表明,被接管材料和管接頭材料之間的熱膨脹系數的差異會造成管接頭系統的室溫強度低於高溫強度;由於不銹鋼的熱膨脹系數較大,使得室溫下1不銹鋼管與n立tinb形狀記憶合金管接頭間的抱緊力遠小於鈦合金管與nitinb形狀記憶合金管接頭間的抱緊力,成功地解釋了拉脫實驗中的結果。The variations of sea ice in the arctic ocean are simulated by using a improved high resolution hibler dynamic - thermodynamic sea ice model during 1979 - 1998. the model is driven by surface atmospheric and oceanic forcing consists of geostrophic winds, surface air temperature, specific humidity, and longwave and shortwave radiative fluxes provided by international arctic buoy program ( iabp ). the simulated results show that arctic sea ice have noticeable seasonal and annual variability
利用一個hibler海冰熱動力模式,在改進了其熱力部分和改變模擬范圍以及提高解析度的基礎上,以北極國際浮標計劃( iabp )提供的1979 - 1998年間逐日變化的日平均海平面氣溫場,濕度場,長短波輻射場,風場,洋流場,海洋熱流量場為強迫場,模擬了上述20年間北極海冰的時空演變。Series of guowei dry - method composite machines as new product are explored with our many years ' experience, the requirement of the users. the first metal of this machine is adopted with : photo - ecectricity auto. tracking " correcting deviation equipment, magnetic powder tension control. pneumatic back pressure shifting blade, oven temperature controlled qutomatically, big roll with oil heating, coating composite pneumatic control as well as double frequency governor etc. it will make the machine with fast speed, lower voice, low polluted by air, shout consumptionfor energy, stable working etc. especially suitable for al - foil with smooth surface and no enough firming, glass paper, polyester ect. the composite material with hard strength, fireproof, anti - ventilation, anti - fatty, frozen, dudrable steam etc character. it is widely used in food, pharmacy, as well as daily articles to package
「國偉」 、系列乾式復合機,是我廠根據多年的復合機製造經驗及結合客戶需求,開發的新產品,該機第一基材採用了「光電自動跟蹤」糾偏放卷裝置,磁粉張力控制、氣動背壓移動式刮刀、烘箱溫度分段自動控制、大輥筒導熱油加熱、上膠復合氣動控制及雙變頻調速技術,使該機具有復合速度快、噪聲低、空氣污染小、能耗低、運行平穩等特點,適宜於表面光滑的鋁箔玻璃紙聚酰胺等與聚乙烯、聚丙烯等薄膜的復合,復合薄膜具有強度高、防水、防透氣、防油脂、可冷凍、蒸煮等優點,廣泛應用冷凍食品、乾燥食品、醫藥品及日用品的包裝。Some other defects in castings are well - defined cracks and hot tears that develop during solidification, under combination of stress concentration from uneven contraction and the metal ' s low strength at near - melting temperatures
鑄件內部的其它一些缺點是,凝固過程中,在不均勻收縮造成的應力集中和接近熔點溫度下金屬的低強度的綜合作用下,出現的清晰裂縫和熱撕裂。Firstly, the surface characteristic of polystyrene particle is changed from water detesting to water intimity by using special techniques and admixtures so mat the compound quality with inorganic materials is insured. secondly, the contradiction between the weight and strength is solved through optimizing the particle size and using composite fiber and the best heat conductivity is achieved under the condition that the necessary strength is met. in the research process, the author solved the problem of fiber dispersing in insulating materials so that the contraction of the material is controlled
課題研究中,首先採用特殊的改性工藝及外加劑實現對聚苯乙烯顆粒表面的成功改性,使其表面由憎水轉化為完全親水,確保與無機材料的復合質量;其次,通過採用優化骨料級配及使用復合纖維等措施解決了保溫材料的輕質與強度的矛盾,使保溫材料在滿足必要的強度的前提下,導熱系數降至最小;並且,課題研究中成功解決了纖維在保溫材料中均勻分散的問題,達到了抑制保溫材料收縮的目的;最後,通過採用復合外加劑、合適的膠凝材料及合理的配比等措施確保該保溫材料具有良好的和易性,滿足施工的要求。The studies indicate that different content of pyrophyllite and dolomite can cause the following three cases : ( 1 ) making the refractory point decrease linearly and, to some extent, influencing the microstructure and properties of sintered body ; ( 2 ) acceleratingmullite formation during sintering, reducing thermal expansion coefficient of bond, reinforcing the matching nature and improving the flexural strength and shock strength ; ( 3 ) preventing sic grinding tool from generating black core, expanding suitable sintering temperature range of sic grinding tool
同時,也不同程度地影響了磨具燒結體的微觀結構和性能; ( 2 )可促進在燒結過程中莫來石的形成,降低結合劑的熱膨脹系數,加強了結合劑與磨料的匹配性,提高了磨具的抗折強度和抗沖擊強度; ( 3 )在一定溫度范圍內還可防止碳化硅磨具出現黑心現象,拓寬了碳化硅磨具的燒結溫度適應范圍。Energy consume, electric strength, insulation resistance, ground conductivity, leakage current, microwave leakage, power input, normal temperature, humidity treatment, glow wire, horizontal flame, vertical flame, tracking, ball pressure, rainproof, water splash, dustproof, salt fog, endurance, motor load test, cord flexing, cord pulling, pull & torque test, lamp replacement, construction check etc
能耗、電氣強度、絕緣電阻、接地連續性、泄漏電流、微波泄漏、功率、溫升、濕熱試驗、灼熱絲、水平燃燒、垂直燃燒、漏電起痕、球壓試驗、防雨淋、防濺水、粉塵、鹽霧、耐久性(壽命)試驗、電機負載試驗、電源線彎折、電源線提拉、拉扭力測試、燈頭互換性、安全結構檢查等。In this paper, features of decadal variability and the possible mechanism of sea - air system in the pacific are investigated by using upper - ocean temperature, heat storage and wind stress data, the main results are as follows : the most pronounce decadal sign exists at about 160 meter in depth in the western pacific. there are significant decadal abrupt changes in temperature from surface to deep in the subsurface at about 1980. with different depth in the subsurface, there exist 4 types of abrupt change modes, their generation is closely related to the decadal sign which originates from the east of north pacific and propagates along the south - west subduct ion route
研究表明,太平洋次表層海溫最強的年代際信號在熱帶西太平洋約160m深處,此信號在1980年前後從上至下,先後經歷了一次顯著的年代際突變過程,而且隨深度的不同存在著四種不同的空間突變模態,這四種模態的形成與北太平洋海溫異常的西南潛沉路徑有著密切的聯系。Iv ) for the strong interfacial coupling, there exist three pyroelectric peaks in the temperature curve of pyroelectric coefficient, and with the decrease of the interfacial coupling, the number of the pyroelectric peaks will decrease gradually
我們還發現,較強的界面耦合導致熱電系數的溫度曲線上的三個熱電峰的出現;而界面耦合強度的減弱及鐵電超晶格尺寸的減少將導致某些熱電峰的消失。The temperature distribution on the high temperature side of an electric tunnel furnace is analysed and simulated on the basis of the principle of thermal radiation by the way of thb ( thermal heat balance ). the heated silicon carbon sticks are decomposed into innumerable tiny heating faces, which exchange the heat with the heated materials. a numerical model based on the radiation intensity law is constructed to calculate the energy absorbed by the heated materials and simulated by a computer. the results showed that the even distribution of temperature can be obtained by optimizing the arrangement of the silicon carbon sticks according to the calculation results to make the structure design more reasonable. these calculation results have been used in the practical designs and the expected objectives achieved
利用熱輻射原理,採用熱平衡法對電熱隧道窯的高溫恆溫區溫場進行了分析和模擬.計算中將發熱棒分解為無數微元發熱面與燒結體進行熱交換,依據輻射強度定律,建立了燒結體接收能量的數學模型,並用計算機進行了模擬計算.結果表明,依據模擬結果來優化硅碳棒的排布,可使結構設計更加合理,進而可以獲得分佈均勻的恆溫區溫場.計算結果已在窯爐設計中應用,實踐效果良好The 5 batches with 31 groups of specimens were carried out four different curing systems including standard curing, hot water curing, dry heat curing and steam curing, and the regularity of rpc200 ' s strength with different curing conditions was studied. a conclusion was acquired by the experiment that the rpc200 ' s strength develops steadily in the steam curing which is mature and the economic benefits is more notable
製作四批23組試件,進行了標準養護、熱水養護、高溫乾熱養護、蒸汽養護等四種不同的養護制度的對比試驗,通過試驗研究發現採用蒸汽養護的rpc200後期強度發展穩定,並且蒸汽養護技術成熟,養護設備無需改造就可用於rpc200構件的養護,具有顯著的經濟效益。It also explain that the correlation between ssta of kuroshio and the change of wind field in equaroral mid - pacific is results of air - sea interaction ; however, when time comes into summer, the instance status of ocean is different from the last winter to next early springtime, the sea surface temperature turn into the definitive factor, so the increase of heat flux in may to jun month which is realized by absorbing more heat from the sun radiation results in the decrease of sst in kuroshio in the season of jun - jul. finally, during the aug to dec season of next year, the sst of kuroshio is increasing again
最後分析了黑潮海溫與夏季東亞大氣環流及我國降水的時滯關系,發現:當前冬黑潮區域海溫異常偏高時,後期夏季亞洲低壓的強度減弱,西北太平洋副熱帶高壓強度加強,而且位置西伸、偏北,梅雨鋒位置偏南,長江中下游地區降水偏多,北太平洋冬季海域的海溫分佈呈+ 、 - 、 +趨勢(順序為赤道中東太平洋、西北太平洋、我國近海) ;反之亦然。Our factory succeeds in developing the new - type lightweight solid aluminium buckle - panel through practice for many years. this kind of metal buckle - panel includes double - sided panel body with one side of the buckle - panel as the bayonet connector, another side as the bayonet, lightweight filling material inside the panel body, fireproofing material filled inside the fireproofing metal buckle panel, possessing better strength of panel body, resulted in sound insulation, heat insulating, more ideal surface luster of the heat insulation panel body and no mechanical veins, beautiful appearance and difficult deformation
本廠經過多年實踐成功研製新型實心金屬扣板,此款金屬扣板包括雙面的板體,板體的一側為卡接頭,另一側為卡口,板體中間帶有輕質填充物,防火金屬扣板中間另注防火材料,具有更好的板體強度,隔音隔熱保溫板體面光澤更加理想無機械紋,外形美觀難變形。The binding principle in pelletizing covers a comprehensive model of interfacial reaction among particles inside green pellets, the formation of binding film during hardening of green pellets by baking to obtain enough strength for a volumetric catalyzed reduction model for cold - bound pellets bearing composite binder and corresponding high temperature reduction system in rotary kiln
提出了含復合粘結劑的生球強度界面作用力綜合模型,冷固球團礦強度的粘結膜機理,含復合粘結劑的冷固球團礦催化還原體積反應機制及全窯高溫快速還原熱工制度。As a result, we find that in winter when the kuroshio is cooler than the normal, at following summer, the continental cyclone deepen and the east asia monsoon strengthen, that the mid - latitude blocking high weaken and zonal circulation develop, the east asia teleconnection of " - + - " is stired up, so that subtropical high weaken and diminish, and tend to east north, tropical monsoon trough strengthen and mei - yu front weaken, and tend to north, meanwhile south asia high weaken and diminish, and tend to eastvnorth, is easy to form eastern region type
結果發現當黑潮海溫冷異常時,後期夏季大陸熱低壓加深,東亞夏季風偏強。中緯度阻塞高壓減弱,東亞地區緯向環流發展,在東亞-西太平洋地區激發「 - + - 」的東亞遙相關型,從而西太平洋副高強度偏弱,面積偏小,位置偏東、偏北,東亞梅雨鋒也偏弱,季風槽則變強,位置偏北。同時南亞高壓偏弱,位置偏北、偏東,易形成東部型。For many years, the drying furnace has been adopted with sealed structure and electrical heated, dial instruments are used to control the temperature of the drying furnace and to keep it invariable. parameter setting is inputted by manual method, heating time is completely controlled by operators ’ experiences or their moods, meanwhile, its control function is singular, not only having no automatic heating time and insulating monitoring, having no drying process monitoring, but also having no function of automatic recording and report printing, the workers ’ labor intensity is bigger. thus two abnormal situations are always come forth, one is the insulating performance and intensity of works cannot be guaranteed reliably, it perhaps need to be dried repeatedly, the other is always to extend the drying time in order to ensure the drying quality
多年來乾燥爐一直採用悶罐式結構和電加熱方式,溫度控制採用指針式溫度控制儀表來實現爐溫的恆定,其參數設定由人工輸入,時間控制則完全憑操作者的經驗、情緒來掌握,其控制功能單一,沒有時間控制、絕緣自動監測功能,也沒有乾燥過程監視功能,更沒有多要素記憶、列印存檔功能,工人的勞動強度較大,所以就經常出現兩種異常結果:一是工件的絕緣性能和強度得不到可靠保證,需要反復乾燥;另一種是為保證乾燥質量,往往要延長乾燥時間。The results indicated that, the fabrication process of ultra - fine grain material is mainly determined by the stress, rotate speed and the flux of cooling water. the grain refining and the hardening effect are mostly affected by the rotate speed and the flux of cooling water. compared with commercial ly12, the invalidate strength and the prolongation rate of the ultra - fine grain material are properly improved in the measurement of compression property ; and the abrupt change of the dilatability of the ultra - fine grain material at 500c is found ; also the phenomena of which the grain size of these microstructures is stable when annealed under 300c is observed
研究表明,採用本文提出的摩擦壓扭強變形區轉移法可以得到棒狀的超細晶材料,軸向壓力、扭轉速度和溫度是採用該方法制備超細晶材料的主控參數;試件的旋轉轉速和冷卻速度對變形區晶粒細化和硬化效果影響顯著;超細晶ly12的壓縮性能與淬火+自然時效狀態的ly12壓縮性能相比,斷裂強度和延伸率均有一定程度的增強;超細晶ly12的熱膨脹系數在550左右發生明顯的變化。In the following finite element computation of thermal - structural strength of an improved designed radome, not only a result consistent with the tests are achieved, and also obtained displacement of the radome is well meeting the test data, well demonstrating a high accuracy of the finite element method and confidence of its results ; and studying on the temperatures and stresses on the radome leads to some valuable conclusions and suggestions to further development, laying a sound foundati on for further improvement of structural reliability of the radome
在接著進行的改進方案天線罩靜熱強度有限元計算中,不僅得出了與試驗結果一致的結論,而且天線罩位移的計算值與試驗數據得到了比較好的吻合,驗證了有限元計算的精度及其結果的可信性;並且通過對天線罩溫度與應力的研究與分析,得出了一些有價值的結論與建議,為導彈天線罩可靠性進一步提高打下了堅實的基礎。Based on those, the concept of chilling process was put forward according to the lowest biologic temperature of main tropic and south sub tropic crop and fruit in guangdong and the low temperature ( environment temperature 5. 0 ) which is harmful to those crop and fruit. with the lowest air temperature ( the daily lowest air temperature ) x1, the lasting days of low temperature x2 and an integrative physical element - - negative accumulated temperature x3 in which the effect of the intense and lasting days of low temperature were considered, the correlation coefficient of those indexes were calculated and analyzed, and the results showed that there are apparent linear correlations among them
在此基礎上,以廣東主要熱帶南亞熱帶作物的生物學下限溫度為依據,從這些作物受寒害的起點溫度(環境溫度5 . 0 )出發,提出了寒害過程的概念,並用寒害過程低溫的強度(逐日最低氣溫) x _ 1 、低溫的持續時間(天數) x _ 2及考慮了低溫的強度和持續時間綜合作用的物理量負積溫x _ 3這3個指標來描述寒害的強度,研究了廣東歷年冬季寒害的變化,分析了這3個指標間的相關系數,結果表明它們之間互相存在顯著的相關關系。分享友人