漸進破裂 的英文怎麼說

中文拼音 [jiānjìnliè]
漸進破裂 英文
progressive failure
  • : 漸副詞(逐步; 漸漸) gradually; by degrees
  • : 進構詞成分。
  • : Ⅰ動詞1 (完整的東西受到損傷) be broken; be damaged 2 (使損壞) break; break down; damage 3 (使...
  • : 裂動詞[方言] (東西的兩部分向兩旁分開) open
  • 漸進 : advance gradually; progress step by step
  • 破裂 : break; fracture; burst; split; rupture; crack
  1. Today, modernization process rapidly exploded the timewom and conservational conception. however, it also dissevered the dialectic connection between building and given place built in last thousands years. a sense of site and belonging is on the wane

    迅速的現代化除了落後保守、固步自封的陳舊觀念,但同時建築與特定地點間維系了幾千年的辯證關系也被割,建築的場所感和歸屬感逐淪落。
  2. In view of soil mechanics, the uplift mechanism is more complicated than any other soil engineering problems. factors such as uplift behavior of soil, crack development, filled soil quality and progressive failure are shown having greatly influenced on pullout behavior

    從土力學觀點來看,基礎上拔機理遠比其它土工問題復雜,土的抗拉性能、土體中縫開展過程、填土質量以及土的壞等因素,嚴重影響著基礎上拔的性能。
  3. According to the practical geological model of slope, by means of the finite element analysis, from the constitutive equations of the elastoplasticity and the viscoelasticity - viscoplasticity, the process and mechanism for progressive failure of the locked segment of rockmass are quantitatively revealed and simulated during the rupture, deformation, destruction, and failure of highsteep slope rockmass, and the dynamics driving the motion of rocky landslide with violent starting velocity by high pressure water flow is dealed with

    根據邊坡實際地質模型,基於彈塑性與粘彈-粘塑性理論的本構方程,通過有限元模擬分析,定量地揭示和模擬再現了高邊坡巖體、變形、壞及失穩前後鎖固段巖體壞的機制和過程,探討了高壓水流作用下滑坡啟程劇動的壞機理。
  4. The evolutional process of landslide can be clearly shown by computer simulation using the model, and the latter prove that the strength of soil on the whole slip surface bring impossibly into play at the same time

    通過數值模擬,清晰地揭示了邊坡壞的歷時演化過程,且實例分析證實,土體的強度並非在整個滑面上同時發揮。
  5. According to the geological conditions of baise project, erosive bands and joint fissures, f6 fault and grout curtain are fully simulated to establish 3d numerical model of the dam and its foundation. 3d non - linear fem is used to analyze the stress and strain and to appraise the operation state of both the dam and it ' s foundation under different operation conditions. by overloading the upstream water level and reducing rock strength parameter, the dam foundation ' s degradation process is simulated and the damage pattern and paths are determined, and finally the safety factor is determined

    2 、根據百色的地形地質條件,充分模擬了蝕變帶、節理隙、 f6斷層、灌漿帷幕等,較為真實地建立了壩體與地基相互作用的整體三維數值模型;採用有限元法對壩體及壩基在不同工況下的應力應變狀態開展分析,評價各工況下壩基的運行狀態;而後採用超載法和綜合法對大壩穩定性行分析,模擬壩基的壞過程,從而得到壩基在超載和強度下降過程中的壞模式和壞發展路徑,最終確定壩基超載安全系數和綜合安全系數。
  6. As for the change of reaction temperature, a good appearance of microspheres will be observed. after heat treatment we obtain the mesoporous sio2 microspheres, the morphology, size and size distribution of microspheres before and after sintering were investigated by using the scanning electron microscopy ( sem ). the desorption of water and ethanol and decompostion of polymers in microspheres were analyzed by using tg - dsc machine

    當r 1時將導致微球產生,而r 4時則生成凝膠狀物質;其他條件不變時,微球形貌隨ph值的增大逐變差,最終;乙醇含量增大時,微球粒徑逐增大;而隨著反應時間的行,顆粒逐長大,微球形貌不斷完善,表面逐平滑;反應溫度的變化會得到更光滑的微球表面,微球粒徑隨之增大。
  7. There are two kinds of model for forming gas pools both in the abnormally pressured compartment and out the compartment in the system. after the breakage of overpressured fluid compartments in silurian system, hydrocarbons generated in the compartments flowed to carboniferous in a phase of mixed fluids

    下伏志留系高壓封存箱生成的油氣隨箱體頂部呈混相涌流入石炭系,油氣在石炭系中向繼承性發育的古隆起運移聚集,形成大型古油氣藏,后逐演化成古氣藏。
  8. If not prevented or if left untreated, osteoporosis can progress painlessly until a bone breaks

    如果未加以預防或不行治療,骨質疏鬆癥會從毫無疼痛逐展至骨頭
  9. At the same time, in order to decrease the break and hollow occurred in machining process, a new method named machining tool - path interactive modification and optimization based on nurbs have been provided for the complicated surface panel and fast - response in machining process of the sheet metal incremental forming achieved

    本文介紹了金屬板材數控成形技術的過程、原理,同時,主要針對加工過程中發生的、凹陷等缺陷,提出了一種基於nurbs的加工軌跡人機交互修改和優化的方法,解決了復雜曲面零件無法加工的難題,實現了金屬板材數控成形加工過程的快速響應。
分享友人