澆注位置 的英文怎麼說
中文拼音 [jiāozhùwèizhì]
澆注位置
英文
pouring position-
Find the law of the influence from the injection pressure to the filling time and the cavity pressure and make certain of the best filling time, injection time and injection pressure. though the analysis of the flowing velocity and pressure spread of the key position element in the injection parts in different gate position, we forecast the injection parts quality and the possibility injection flaw and its position, optimize the gate position. in this paper, though the research of analogue of the runner system of metal - powder injection molding and the process of injection molding, we get the law of how the injection parameter influence the injection process
在相同的注射條件下，通過分析喂料在不同直徑和長度流道中的流動規律，得到了喂料在流道中的速度場、壓力場和溫度場，找到了流道長徑比的合理取值范圍，並得出通過改變流道設計可實現對現有設備資源充分利用的結論；給出了不同注射壓力下，型腔壓力與充模時間關系曲線和喂料熔體平均充填速度與充模時間關系的曲線，得到了注射壓力對充填時間和型腔壓力的影響規律，確定了最佳的充模時間、注射時間和注射壓力；通過分析採用不同位置澆口注射時注射件關鍵位置單元的流動速度和壓力分佈，預測了注射件的成形質量，或可能產生的注射缺陷及位置，優化了澆口設置。The composite material, which is used to make muller plow of sand mill, is prepared by the method of cast - infiltration and the technology parameters for making composite material is optimized. then the effects of the matrix component on composite layer also are disccused
通過試驗對利用鑄滲法在鑄件表面獲得一定厚度復合材料層的形成機理進行了理論分析，優選了利用鑄滲法在鑄件表面制備復合材料的工藝參數（澆注溫度、合金膏塊的厚度、澆注位置等） 。Wear resistant layer of cylinder and double - layer liner in catalyst creaking apparatus ( without or with tortoiseshell net can be used ), inner liner of carbon monoxide exhaust - heat boiler, pouring at site for furnace roof with high temperature of heating furnace of steel rolling, different forging furnace, resistance furnace, the prefabricated parts can also be made
催化裂化裝置中的筒體耐磨層及雙層襯里， （無龜甲網和有龜甲網均可採用）及一氧化碳余熱鍋爐的內襯，也適用於軋鋼加熱爐、各種煅造爐、電阻爐的爐頂、爐墻、爐底高溫部位的現場澆注，可製成預制構件。Once again using moldflow injection molding simulation software, engineers analyze how a part should be molded accounting for gate locations, wall thicknesses, size, and type of material
根據澆口位置、壁厚、零件大小和注塑材料的種類，使用注塑模擬軟體，分析零件應該怎麼樣模塑。Reference to the designation of die casting mould, we put forward some kinds of projects respect to the design and manufacture of dies of the special purpose machine. and we simulate die casting filling process 、 surface defect distribution and temperature field etc. of az91d magnesium alloy shell part with flow3d software
設計時將參照壓鑄模的設計方法，提出多種方案，並使用flow3d模擬設計軟體來模擬金屬液的填充過程，預測可能產生缺陷的位置，從而決定澆注系統的形狀和分佈，冷卻水道的流向和位置，分流錐的大小和位置。分享友人