澆注線 的英文怎麼說

中文拼音 [jiāozhùxiàn]
澆注線 英文
teeming line
  • 澆 : 澆名詞（姓氏） a surname
  • 注 : Ⅰ動詞1 （灌入） pour; irrigate 2 （集中） concentrate on; fix on; focus on 3 （用文字來解釋字句）...
  • 線 : 名詞1 （用絲、棉、金屬等製成的細長的東西） thread; string; wire 2 [數學] （一個點任意移動所構成的...
  1. The thesis has summarized the development of the oblique - pull bridge, its construction technology and the importance of bridge construction control, then has introduced project general situation, and has narrated detailed regulation, organization construction, the major work and difficult part of this bridge construction control. the following is the key part of this thesis, firstly, it has introduced the experiment work of early stage, structural calculation and its theoretical result : the absolute altitude of each operating mode, the absolute altitude of building mould in each section and the absolute altitude after pouring concrete ; then, it has discussed the method and content of the line shape control of the main beam, actual absolute altitude of building mould is put forward, and it has described the method of structural stress monitoring, how to arrange measure point and collect data, and how to analyze data. it has also narrated the method of rope force detection and structural temperature inspection

    本論文在總結了斜拉橋的發展及其施工工藝，並指出了橋梁施工控制的重要性之後，簡要的介紹了工程概況，敘述了炳草崗金沙江大橋監控細則、組織機構及監控的主要工作和難點部分；論文的核心部分，在介紹了炳草崗金沙江大橋施工控制與監測工作的前期實驗工作和施工各工況標高、各節段支模標高、澆注混凝土后的標高的結構計算和其理論計算結果之後，詳細論述了主梁的標高線形控制方法和內容，實際支模標高的提出，結構應力監控的方法、布點、測讀及其對測讀數據的合理分析方法，索力檢測和結構溫度監測的方法。
  2. The current transformer is fully enclosed and busbar structure. the secondary windings and iron core are insulated by epoxy resin. it has a good ability of antipollution and moisture proof

    本型電流互感器為全封閉母線式結構，二次繞組及鐵芯均澆注在環氧樹脂內，耐污染及潮濕。
  3. The key products of the company are high alumina brick, fireclay brick, phosphate - bonded wearable brick, exfoliation - resistant high alumina brick, high refractoriness under load brick, corundum brick, magnesite brick, magnesite ? chrome brick, series of corundum, sic furnace chamber and pipe, ceramisite brick, corundum - mullite brick, corundum - chrome brick, sillimanite brick, magnesite alumina spinel brick, acid - resistant brick, alkali - resistant brick, zirconia - corundum brick, alumina bubble products, series thermal insulating refractory products, high alumina castable, corundum castable, corundum ramming, brown - corundunm castable, sic castable, low - cement castable, alkali ? resistant castable, light silica alumina products, stainless steel fibre reinforced castable, etc

    主要產品有：高鋁質磚、粘土質磚、磷酸鹽耐磨磚、抗剝落磚、高荷軟磚、剛玉磚、碳化硅磚、鎂磚、鎂鉻磚、各種剛玉、 sic爐膛、爐管製品、陶粒磚、剛玉莫來石磚、鉻剛玉磚、硅線石磚、鎂鉻尖晶石磚、耐酸磚、耐堿磚、鋯剛玉磚、氧化鋁空心球製品及各種輕質保溫材料、高鋁質澆注料和剛玉澆注料、搗打料、棕剛玉澆注料、碳化硅澆注料，低水泥澆注料、抗堿性澆注料、輕質硅酸鋁製品、鋼纖維增強澆注料等80餘種系列耐火材料。
  4. Behavior of linear expansion of corundum - spinel castables in sintering process

    尖晶石質澆注料燒成過程中的線膨脹行為
  5. The wax setting and casting process is complicate process with a series of procedures, including model creating, spruing and construction, rubber mold vulcanization and cutting, wax models injection, stone setting in wax model, wax tree creating, investing, investment mold burning - out, metal melting and pouring, casting cooling and divesting, etc

    蠟鑲鑄造是一個多工序的復雜工藝過程，包括母版製作、開設水線、製作橡膠模、製作蠟模、寶石鑲嵌到蠟模、種蠟樹、製作石膏型、石膏型脫蠟焙燒、金屬熔煉澆注、飾件冷卻清理等。
  6. Berkeley production companies using the national patent - - normal atmosphere temperature for approximately foam phenolic resin made by national patent technology - - phenolic foam composite wind normal atmosphere temperature control plate consecutive foam methods, the introduction of an internationally advanced level of industrial production lines, and through iso9001 ~ 2000 iso14001 ~ 1996 certification consistent with national enterprise development direction

    貝克萊公司生產採用國家專利的? ?常溫連續發澆注發泡酚醛樹脂，按國家專利技術? ?酚醛泡沫復合風管板材常溫連續發泡方法，引進具有國際先進水平的工業生產線，通過iso9001 ~ 2000及iso14001 ~ 1996認證，符合國家企業發展方向。
  7. We insist on " survival depending on quality ", and passed iso9001, iso14001, the products are approved by cnacl, dnv, bv, ccs, we always use advanced technology and equipments such as vacuum casting equipments from german hedrich company, foil winding machines, partial discharge detectors and lightning impulse voltage gener - ators, we shall provide our customers with super quality products and good service

    公司始終以一流的設備及先進的檢測手段，如德國hedrich公司的真空澆注設備箔式繞線機局放儀雷電沖擊試驗設備等，以全體員工精湛技藝和精益求精的工作作風，竭誠為用戶提供優質的產品和優良的服務。
  8. Ghg - electrical grade activated silica powder is produced by way of mingling on the basis of electrical grade silica powder. it has activt effect on surface & make silica powder mingled with resin, raise cohesive force between resin & silica powder, raise the water - resestance on the sunface and the compressive strength of pour object, reduce sediment, gradation & split, increase filler of silica powder, and replaced inpoted products on the producing line of imported dry type transfomer & high tension mutual induc tance equiment, it has been the best pouring insulate materual in electrical trade

    電工級活性硅微粉是在電工級硅微粉的基礎上進行偶聯化處理而製成，具有表面活性作用，能使用硅微粉與樹脂發生交聯，提高樹脂與硅微粉的粘結力和界面增水性，提高澆注體抗沖擊強度，減少沉澱、分層、開裂現象，增加硅微粉的填充量，在引進的乾式變壓器、高壓互感器生產線上已成功地代替了進口產品，成為電工行業理想的環氧澆注絕緣材料。
  9. Find the law of the influence from the injection pressure to the filling time and the cavity pressure and make certain of the best filling time, injection time and injection pressure. though the analysis of the flowing velocity and pressure spread of the key position element in the injection parts in different gate position, we forecast the injection parts quality and the possibility injection flaw and its position, optimize the gate position. in this paper, though the research of analogue of the runner system of metal - powder injection molding and the process of injection molding, we get the law of how the injection parameter influence the injection process

    在相同的注射條件下，通過分析喂料在不同直徑和長度流道中的流動規律，得到了喂料在流道中的速度場、壓力場和溫度場，找到了流道長徑比的合理取值范圍，並得出通過改變流道設計可實現對現有設備資源充分利用的結論；給出了不同注射壓力下，型腔壓力與充模時間關系曲線和喂料熔體平均充填速度與充模時間關系的曲線，得到了注射壓力對充填時間和型腔壓力的影響規律，確定了最佳的充模時間、注射時間和注射壓力；通過分析採用不同位置澆口注射時注射件關鍵位置單元的流動速度和壓力分佈，預測了注射件的成形質量，或可能產生的注射缺陷及位置，優化了澆口設置。
  10. Three separately managed and marketed companies that manufacture coil processing equipment, ashphalt shingle and paving machinery, and metalforming machines for shaping hollow cylindrical blanks. site incorporates links to detailed information about each company and its products

    -生產聚氨酯設備，產品包括聚氨酯鞋底成型機聚氨酯連幫成型機聚氨酯高壓發泡機聚氨酯低壓發泡機聚氨酯彈性體灌注機聚氨酯精密灌膠機聚氨酯澆注機聚氨酯發泡機組及聚氨酯生產線等。
  11. They are cast without air bubble with imported high quality resin material under the vacuum condition, the lv windings are made of copper foil as the capacity requirement

    高壓線圈用銅線繞制，玻璃絲纖維增強，採用進口優質環氧樹脂，在真空狀態下實現無氣泡澆注。
  12. High strength, good volume stability, low thml. cond. ， and can be installed by casting, gunning or ramming

    強度高，燒后線變化小，導熱率低，可澆注、噴射、搗打施工。
  13. High strength, low linear change and low thermal conductivity. forming easily, such as casting, gunning, coating, ramming

    強度較高，燒后線變化小，導熱率低，施工方便，可澆注、噴射、塗抹或搗打施工。
  14. The voltage transformer is fully enclosed type the iron core is piled up of the cold roll silicon steel sheet. the iron core, primary and secondary windings are casting resin by advanced vacuum carting equipment. it has a good ability of antipollution and moisture proof. the secondary outlet is wrapped by outlet box with three exits with different directions. it, s convenient. it can prevent from stealing electricity

    本系列電壓互感器為全封閉式結構，鐵芯採用優質冷軋硅鋼片繞制，並經嚴格的熱處理，鐵芯與一次繞組和二次繞組一起以先進的真空澆注工藝用環氧樹脂澆注成型，互感器耐污穢，耐潮濕性能好二次出線端子有出線端子盒，端子盒有三個不同出線方向接線方便，並可實現防竊電措施。
  15. The purple sand hand - drag base art breaks the banlance of old hitting base art and dang - base model from song dynasties to now

    紫砂手拉坯工藝打破了自宋代起至今的傳統打坯鑲接成形法與模型擋坯、灌漿澆注成型法的一統天下，避免了傳統成型所留下的泥條接頭線與模型接線。
  16. The current transformer is busbar type. the secondary windings and iron core are insulated by epoxy resin. the middle hole is used for busbar going through and mounting

    本型電流互感器為母線式。二次繞組及鐵芯均澆注在聚脂樹脂內，中間窗孔供一次母線穿過及安裝用。
  17. By close study on the average temperature rise, temperature distribution, and tune constant of the class f resin dry type power transformer ' s high voltage and low voltage winding under self - cooling and wind - cooling mode, we find out the connection between the variation of the load and the items, mentioned above. the results of the experiments can be reference to both thermal design optimization of dry type power transformer and the revision of current standards. meanwhile, we develop the software, which can predict the overload ability of the dry type power transformer

    本文對f級樹脂澆注式乾式變壓器的高、低線圈的平均溫升，內部溫度分佈和時間常數在自冷和風冷，兩種冷卻方式下隨負載變化的規律進行了研究，得出了平均溫升、熱點溫升和時間常數隨負載變化的相互關系和有關計算用參數和公式，試驗結果可作為改進乾式電力變壓器的熱設計的依據和對現行標準進行修改的參考。
  18. High - voltage feed - through terminals with cast resin insulator

    澆注樹脂絕緣子的高壓引線端子
  19. Before casting, the top and / or bottom layer materials can be processed for the purposes of embossing, corrugating or other necessary treatments either on the line or off the line, depending on the materials of the top and / or bottom layers and their shapes

    根據面層材料的不同和面層外形的差異，在澆注前，面層材料將在生產線上或線外進行壓印，軋瓦楞或其它必要的處理。
  20. Light quality indefinite type pour material is it insulate against heat of good performance to have, heat conduction coefficient little, energy - conserving result remarkable, the intensity is high, the line changes littly, various kinds of stove kiln ideal inside lining, adiabatic material, please according to select different materials for use while being different kinds of, it is easy to economize the kiln cost

    輕質不定型澆注料具有隔熱性能好、導熱系數小、節能效果顯著、強度高、線變化小，各種爐窯理想的內襯、絕熱材料，請按不同類型選用不同材質，便於節約窯爐成本。
分享友人
分享到 Line

分享到臉書