澆鑄號 的英文怎麼說
中文拼音 [jiāozhùháo]
澆鑄號
英文
cast number-
Feeding, ingate design, air discharge, position of signal wire were analysed and discussed, aiming at the several questions in production of low pressure casting
摘要根據低壓鑄造工藝的特點和生產實踐，從補縮、內澆道設計、排氣、信號線安放位置等方面進行了分析和探討。On basis of the development of modern control technology and apply of the network technology and locale bus - mastering technology ， the paper analyzes the essential element of slab caster system : casting speed ; expatiates in detail on the network structure and communication protocol of ethernet and profibus - dp ; mainly describes the forms of control system configuration ， the function and features of its software and hardware designs ; also, introduces mainly control function of control system, for example ， sequence control, tracking system and operation and monitor function etc. and analyzed and settled the problems of control system in debugging and producing
根據傳統的控制系統存在的一些不完善的問題，基於現代控制技術的發展、網路技術以及現場總線技術的應用，從多方面考慮，決定控制層採用siemens的s7 - 400plc ，現場採用遠程i / o單元，很好的解決了信號量大而又分散的問題。針對生產工藝和機械設備的控制要求，設計了齊全的操作模式和方式，分析了板坯連鑄系統的基本要素：拉矯速度（澆鑄速度） ；根據控制功能的分配及實現，主要說明了plc控制系統的組織結構形式，系統的軟硬體設計的功能和特點。There are five parameters need to be measured. there are five channels for input : the displacement of casting - roller, the rotate speed of casting - roller, the pressure of casting and rolling, the casting temperature and the water - speed of cooling water. they are measured by raster, photoelectric coder, strain pressure sensor, thermocouple and turboflowmeter
系統需要進行監測的參數有五個，即有五路輸入信號：鑄輥位移、鑄輥轉速、鑄軋壓力、澆鑄溫度、冷卻水流速，分別採用光柵、光電編碼器、應變式壓力傳感器、熱電偶和渦輪流量計作為檢測元件。The dissertation mainly introduces the research and development work of ladle - tundish slag detection. after lots of investigation of the internal and external slag detection technology and data analysis, the dissertation brings forward ladle - tundish slag detection method using vibration measurements and analyzes the characteristic of the molten steel vibration signal
在對國內外下渣檢測方法的廣泛調研、資料分析和總結的基礎上，提出了基於鋼水澆鑄結構振動監測的下渣檢測方法，並對鋼流的振動信號處理與鋼渣特徵參數的識別方法進行了研究。We adopt the semi continuous pouring process and mainly manufacture the products marked 1xxx 3xxx 4xxx 7xxx 8xxx and the like by means of 1500 hot - rolling mill, 1400 cold - rolling mill, 1400 mill of aluminum strip and foil, 800 roughing or finishing aluminum foil mill
產品介紹本公司採用半連續澆鑄工藝，經1500熱軋機， 1400冷軋機， 1400鋁帶箔軋機及800鋁箔粗中精軋機等鋁材，主要生產1xxx ， 3xxx ， 4xxx ， 7xxx ， 8xxx等系列牌號。分享友人