焊接反變形 的英文怎麼說
中文拼音 [hànjiēfǎnbiànxíng]
焊接反變形
英文
preset-
Therefore, in order to understand the long - time performance of the weld, it is necessary to study the welding interface of niobium alloy and stainless steel, and know the microstructure evaluation. explosive welding and vacuum electron beam self - material brazing were used to prepare the specimen
因此，研究鈮合金與不銹鋼的焊接結合層，分析形成的互擴散層的組織、成分和性能變化，對了解不銹鋼和nb合金的互擴散反應行為，焊接件的焊接工藝改進和長期使用性能的評估是很有意義的。Welding position : if the configuration collocation of weld is symmetry and the welding sequence is reasonable, the longitudinal contraction and transverse lateral contraction deformation are usually produced, incontrast, the bending deformation is usually produced
焊接位置：如果焊縫在結構布置對稱，焊接順序合理時，則主要產生縱向收縮和橫向收縮變形，反之，則要發生彎曲變形。Thermal and welding residual stress often produces in the proceeding of the electronic package, the residual stress release and thermal deformations of the microelectronics will reduce the assemble intensity between the chip and package, and then debase the electrical performance of the assemble circuit, numerous thermal cycling will lead to thermal fatigue or thermal failure of the microelectronics
電子封裝器件在生產的工藝過程中，往往會產生熱殘余應力以及焊接殘余應力，殘余應力的釋放作用及器件在使用過程中的熱變形，會降低集成電路晶元與封裝體的結合強度，進而降低集成電路的電性能，反復的熱循環，將導致器件的熱疲勞失效，嚴重時可導致矽片或陶瓷片破裂，使整個器件遭到破壞。It was found that the interfacial bonding of 93w - ofc was both the joining action of ofc / w grains and that of ofc / ni - fe binders, whereas the joining of ofc to tc4 could be seen as the mutual intense diffusion effect between ofc / tc4 and as a result cu - ti intermetallic compounds were formed at the joint. the joining of tc4 - a1 and a1 - mb2 were also attributed to the result of diffusion between elements ti - al and al - mg respectively. on the other hand, residual thermal stress and stress - induced distortion were produced at the joint simultaneously due to the difference in thermal expansion coefficient of different welding " materials
研究表明， 93w與ofc的界面連接是ofc與93w中w晶粒的連接以及ofc與93w中ni - fe粘接劑的連接共同作用的結果； ofc與tc _ 4連接界面的形成是由於ofc與tc _ 4之間發生反應擴散，並由此在二者接頭處生成了cu - ti金屬間化合物的中間相； tc _ 4 - al的連接與al - mb _ 2的連接則分別是其基體元素ti 、 al之間和al 、 mg之間元素互擴散的結果，另外，由於熱膨脹系數的差異，擴散焊接后在不同焊件的接頭處存在殘余熱應力並由此引起接頭的形變。Reducing partial rigidity : when closed weld or the weld which has less rigidity are welded, we can take anti - deformation way to reduce the partial rigidity of component
降低局部剛性：焊接封閉焊縫或其剛性較大的焊縫時，可以採取反變形法來降低結構的局部剛性。分享友人