焊接性不良的 的英文怎麼說

中文拼音 [hànjiēxìngbùliángde]
焊接性不良的 英文
difficult-to-weld
  • 焊 : 動詞（用熔化的金屬修補金屬器物或使金屬工件連接起來） weld; solder
  • 接 : Ⅰ動詞1 （靠近;接觸） come into contact with; come close to 2 （連接; 使連接） connect; join; put ...
  • 性 : Ⅰ名詞1 （性格） nature; character; disposition 2 （性能; 性質） property; quality 3 （性別） sex ...
  • 不 : 名詞[書面語] （剁物所用的木墩） a block of wood
  • 良 : Ⅰ名詞1. （善良的人） good people 2. （姓氏） a surname Ⅱ形容詞（好） good; fine; nice Ⅲ副詞（很） very; very much; indeed
  • 的 : 4次方是 The fourth power of 2 is direction
  • 焊接 : weld; welding; soldering; seal; sealing; sealing-in; shutting together
  1. In this thesis, four types of steel beam - rectangular cfst column connections, including normal welded flange plate ( wfp ) connection, bolted flange plate ( bfp ) connection, stiffened end plate ( sep ) connection and double split - tee plate ( dst ) connection, were designed based on the configuration of steel frame connection. total 8 models, 2 models of each kind of connections were tested under low - reversed cyclic loading at the end of cfst columns. the relationships between force and displacement at the end of columns, the relationships between the moment and rotation of the joints, degradations of strength and stiffness, ductility, failure mechanism and failure characteristics of these four connections under different axial - compression ratios were presented

    本文借鑒鋼框架節點構造，設計了四種類型矩形鋼管混凝土柱與鋼梁連接節點，包括常規栓焊（ wfp ）節點、翼緣全螺栓連接（ bfp ）節點、雙t板連接（ dst ）節點以及加勁端板連接（ sep ）節點，進行了四類節點8個模型試件在柱端低周反復荷載作用下的抗震性能試驗研究，比較了不同軸壓比下節點的滯回性能、強度與剛度退化、延性、破壞機理與破壞特徵，主要結論有： 1 、節點的位移滯回曲線與轉角滯回曲線為塊型分佈，沒有或略有捏攏現象，耗能能力強； 2 、軸壓比對節點滯回曲線有顯著影響，全部節點都有顯著的剛度退化； 3 、位移與轉角骨架曲線在峰值荷載後有較長的水平或下降段，具有良好的延性性能； 4 、從整體抗震性能上看，翼緣全螺栓連接節點、雙t板連接與加勁端板連接節點都優于常規栓焊節點，可在實際工程中加以推廣。
  2. It balls up well in ac welding and has a more stable arc than pure tungsten. especially with excellent performance in high load ac welding, it is not replacable by any other electrodes. it also resists contamination well in ac welding

    尤其在高負載電流的情況下，鋯鎢電極表現出來的優越性能，是其他電極不可替代的，在焊接時，鋯鎢電極的端部能保持成圓球狀而減少滲鎢現象，並具有良好的抗腐蝕性。
  3. Based on the process of the wall preparation, erection and welding from the practice of some 10, 000 m ^ 3 oil tanks with an inner floating drum, this article analyzes the phenomena and causes of the wall deformation and puts forward the relevant controls for a variety of the wall deformation, which have already achieved reasonable effects

    本文結合10000立方公尺內浮頂油罐的工程實踐，從預制加工、組裝、焊接全過程分析壁板變形的各種現象和成因，針對壁板變形的不同情況提出有針對性的控制措施，取得了良好的控制效果。
  4. The dcep mig has the characteristic of deeper penetration which can reduce defective fusion and good arc stabilization. the dcen mig has the characteristic of shallow penetration of welding seam, and the welding wire has a high melting speed. so the variable polarity pulsed mig is a new technology for the welding of aluminium alloy sheet

    變極性脈沖mig焊是一種新的焊接工藝方法，其綜合了dcep脈沖mig焊熔深較大、可以減少焊縫的熔合不良、電弧穩定性好和dcenmig焊焊縫熔深淺、焊絲熔化速度較快的特點，減小了焊縫的熔深，增加了焊絲的熔化速度，是一種適合於薄板鋁合金焊接的新方法。
  5. The result proves that composite beams with partial shear connectors have better performance to support fatigue load in that they can hardly be destroyed under general fatigue load if the welding quality is reliable

    試驗結果表明，重復荷載作用下的部分剪力連接組合梁具有良好的抗疲勞性能；在焊接質量有保證的情況下，處于正常使用范圍內的疲勞荷載作用下的部分剪力連接組合梁幾乎不會發生疲勞破壞。
  6. Cerium tungsten electrodes have easy arc starting performance and low are keeping current. it is especially used to weld pipes, stainless steel articles and fine miniparts

    鈰鎢電極在低電流條件下有著優良的起弧性能，維弧電流較小，因此，它常常用於管道、不銹鋼製品和細小精緻部件的焊接。
  7. Lanthanated tungsten electrodes attract close attention and become popular in international welding area for its unique welding performance. it is easy to use under ac or dc conditions

    鑭鎢電極因其具有良好的焊接性能而在國際焊接界倍受關注，鑭鎢電極不管在交流還是直流條件下使用都能輕松自如。
分享友人
分享到 Line

分享到臉書