焊透 的英文怎麼說
中文拼音 [hàntòu]
焊透
英文
complete fusion-
This indicated that the fracture had initiated at the unfused butt weld in the longitudinal stiffener.
研究表明裂紋是從縱向加勁助未熔透的對接焊縫中起始的。Some crack extension probably developed from the unfused section of the butt weld across the thickness of the stiffener during transport and erection.
有些裂紋可能在運輸和安裝過程中就從加勁肋對接焊未熔透處開始發展。The solder is heated to its melting point in a reducing atmosphere, so that the joining takes place without flux as the solder fuses and then infiltrates the gaps between the two pieces to be joined by means of capillary action, creating a highly airtight seal
在高精度狹窄的空隙中也能通過毛細管現象進行浸透並和母材焊接,因此可實現高氣密性,獲得比母材更高的強度。Medium frequency induction heating equipment are used in metal melting, temperature keeping, diathermic technology, metal - heat processing brass soldering, quenching, tempering and sintering
中頻感應加熱設備適用於各種金屬熔煉,保溫,透熱,金屬熱處理,釬焊,淬火回火,燒結,釬絲鋼絲等。Dye penetrant examination of the completed weld
對已完成的焊縫進行著色滲透檢測。Hence lack of fusion and slag would exist at the weld root and create a large initial crack condition.
因而未熔透及夾渣存在於焊縫棍部,並造成大的初始裂紋條件。Slag, blowholes, and paint on unfused regions were observed at the welded junctions.
在焊接處看到了夾渣,氣孔及未熔透區的油漆。When flux appears liquid and transparent on both tube and valve, start sweeping flame back and forth along axis of joint to maintain heat on parts to be joined, especially toward base of valve socket
當焊劑變成液態並且在管道和閥門上呈現半透明狀態時,開始將火焰沿著連接部件的軸線進行進退烘烤,以保持連接部件、特別是閥門套筒底座部位的熱度。In this paper, it has been studied by the slope - controlled scr rectifier that external characteristic of welder relate to arc digging action and the strong arc force of arc welding power source in manual arc welding formed
利用一種特製的變結構可控硅整流焊機,研究不同焊機外特性對電弧穿透力的影響;探討了手工電弧焊強電弧力形成機理;並且指出正確設計電源外特性,是獲得較強電弧穿透力的途徑。Often lack of fusion adjacent to the girder web in the transverse groove welds led to the cracking.
在靠近主梁腹板的橫向坡口焊縫處常常出現未熔透而導致裂紋。Dye-penetrant and magneticparticle inspection techniques were used on the repaired and other 21 remaining original welds.
在已修補了的和其餘21個原來的焊縫上進行了著色滲透和磁粉探傷工藝處理。It has mang virtues such as weld moulding beauty, weld quanlity credibility and so on, espcially it can conquer not weld fully, not fusion and so forth fatal vice
它具有焊縫成型美觀、焊接質量可靠等優點,特別是對克服常規焊接方法中的未焊透、未熔合等危險性缺陷具有重要意義。Rays with high penetrating power are used to image defects in welds and metal castings
在工業方面,射線穿透力特強,可用作探測焊接點和金屬鑄件的裂縫。Partial penetrated butt weld
不焊透對接焊縫61Internal defects : lack of penetration, lack of fusion, slag, gas pole, carck, overheating
內部缺陷:未焊透、未熔合、夾渣、氣孔、裂紋、過熱。All welds shall be full penetration and continuous unless otherwise specified on the drawing
除非圖上另外標明,所有焊縫均為連續全焊透焊接。Electrical installations in ships - part 390 : cable penetrations - fire type test procedure
船上的電氣安裝.第390部分:電纜的熔焊透.著火型試驗過程Specification for welding primers and weld - through sealants, adhesives and waxes for resistance welding of sheet steel
板材鋼電阻焊用焊接底劑焊透密封劑粘合劑和蠟規范Diamond core drill can be laser welded with full penetration and the bonding strength is 1500 n / mm2. dendrite morphology and porosity formed in the welds of al - fe - v - si aluminum alloy
用本激光器對金剛石薄壁鉆進行焊接,可以將其完全焊透,抗彎強度為1500n / mm ~ 2 。The commonly used methods of connections, especially the high - strength bolted connection and welding with bolting mixed connections are discussed in more detail. the analysis for the problems, such as partial penetrated butt weld and welding deformation is also discussed in the paper
對工程中採用較多連接如高強度螺栓連接、栓-焊混合連接等作了較深入分析;對工程中容易出現問題連接如不焊透的對接焊縫計算方法及可能出現的焊接變形及處理等問題也作了較深入探討。分享友人