熔化端 的英文怎麼說
中文拼音 [rónghuàduān]
熔化端
英文
melting end-
Ultramafic rock fragments, which almost is altered to ophite, distributed in structural zone and displayed structural lens. so far, 9 fragments were discovered and mapped in nujinshan and bujing area ultramafic rock can be divided two kinds according to it ' s geochemical characteristics. one can be correlated with metaperidotite, which represented residual part that primary pyrolite underwent moderate partial melting, from some representative ophiolite melange in the world
按超鎂鐵巖類的地球化學特徵可將其劃分為兩類：一類具有較高而穩定的mgo 、較低的al _ 2o _ 3 、極低的cao ， m f值為8 . 0 ? 8 . 4 ，按標準礦物組合進行分類可定為方輝橄欖巖，且均為fa _ （ 100 ） 、 en _ （ 100 ）的鎂質端元組分；可與世界上一些典型的蛇綠巖套中變質橄欖巖進行對比，代表了原始地幔中等部分熔融作用后殘余物。The welding technology of francis turbine runners is optimized from the view of subsection welding and local heating by numerical simulation. the result shows that welding residual tensile stress appears in the weld and its area nearby, and peak stress appears in the dangerous area of blades after practising quondam welding technology ; welding residual tensile peak stress in the dangerous area of blades can be decreased by welding both ends earlier and then welding middle section later during subsection welding, and decreasing effect on welding residual stress of the subsection welding is related to the weld length of blade outlets and welding direction of each subsection ; decreasing effect on residual stress of the local heating is direct proportional to heating time, heating temperature, heating area, and inversely proportional to cooling area, and welding residual tensile peak stress in the dangerous area is decreasing trend earlier, and then increasing trend later with heated location increased
本文利用數值模擬手段對轉輪的焊接工藝從分段焊和局部加熱兩個方面進行了優化，結果表明:採用普通工藝焊接時，葉片焊后殘余拉應力出現在焊縫及其附近區域，並且在葉片出水邊的熔合線附近（危險區域）出現了峰值;在採用優化的分段焊時，先焊兩端后焊中間的方法可以降低葉片危險區域的焊接殘余拉應力峰值，降低效果與葉片出水邊焊段長度、焊縫各段的焊接方向有關;局部加熱法降低轉輪危險區域殘余應力的效果主要與加熱時間、加熱溫度以及加熱面積成正比，與冷卻面積成反比，並且危險區域的殘余應力隨加熱區域的增大呈先降低后升高的趨勢。5, both melting point ( tm ) and isotropization temperature ( tj ) of all the three series compounds change regularly with the carbon numbers of the end alkoxy group increased. there is a gradual increase in smectic phase length and in the smectic - nemetic transition temperature. at the same time there is a gradual decrease in nemetic phase length
五，三個類型化合物16ia至16id 、 16ila至16lid 、 17ia至17id 、 17ila至17lid 、 18ia至18id和18ila至18lid的熔點和液晶態的清亮點均化合物分子中末端烷氧基增大逐漸降低；近晶相的溫度范圍和近晶相一向列相轉變溫度逐漸增大，而向列相的溫度范圍遞減。Add metal from the rod by dipping the end into the pool so that it melts and makes up the vee.
將焊條一端浸入池內熔化，填滿V形坡口。With the increase of the end - group ' s volume, the melting points and clearing points followed the same trend while the stability of liquid crystalline states became worse
隨著末端基脂肪鏈體積的增大，熔點和清亮點具有同樣的變化趨勢，液晶態的穩定性變差。The technical breakthroughs in growth of nd : cngg had been made. in particular, continuous laser operation was achieved from nd : cngg pumped by ld. when the crystal wafer was end - pumped by one bar of ld with 807nm wavelength, the cw laser output power of 123. 1 mw was obtained with slope efficiency of 22. 3 %
本論文用自動化熔體提拉技術成功生長出< 111 >方向的直徑25mm以上，長度80mm以上的平界面無核心nd : cngg單晶，確定了晶體結構和物相，測量了晶體的光譜性能，晶體消光比達到34db ，晶體生長技術有新的突破，實現了連續激光運轉，用單支807nm半導體激光二極體端面泵浦該晶體片子，在國內首次獲得123 . 1mw的1 . 062 m連續激光輸出，斜效率達22 . 3 % 。Surely a telltale hole in the melted wax would expose an end of the metal capsule concealed in the base of the candle
熔化的蠟燭油中間那個一覽無疑的空洞無疑會露出藏匿在蠟燭根部的金屬囊的一端。Add metal from the rod by dipping the end into the pool so that it melts and makes up the vee
將焊條一端浸入池內熔化，填滿v形坡口。分享友人