熔化電弧焊 的英文怎麼說

中文拼音 [rónghuàdiànhúhàn]
熔化電弧焊 英文
arc welding with consumable
  • 熔 : 動詞（熔化） melt; fuse; smelt
  • 電 : Ⅰ名詞1 （有電荷存在和電荷變化的現象） electricity 2 （電報） telegram; cable Ⅱ動詞1 （觸電） give...
  • 弧 : 名詞1. [數學] （圓周的任意一段） arc2. （古代指弓） bow
  • 焊 : 動詞（用熔化的金屬修補金屬器物或使金屬工件連接起來） weld; solder
  • 熔化 : melt; smelt; meltdown; fusion; fusation; diatexis; eliquation; run; melting; smelting
  1. Using the traits of arc adjust itself of the co _ 2 welding, adopting slow - descending feature or even feature of electrical source equipping with system that delivering the welding rod at the invariable speed, then, the arc burning steadily is realized, and the quality of welding is improved

    利用co _ 2氣體保護焊電弧的自身調節特性，採用緩降或平硬特性的電源配等速送絲系統，通過改變電源空載電壓來調節電弧電壓，再利用電弧電壓和熔化速度之間的關系調節焊絲熔化速度使之等於送絲速度，最終實現電弧的穩定燃燒。
  2. Due to two work states - - - arc burning and short current - - - existed in welding process of consumable electrode welding, and different control objectives in these two states, two close - loop feedbacks are designed in the control system : welding voltage feedback and welding current change rate feedback

    根據熔化極co2焊機具有燃弧和短路兩種工作狀態，且兩種狀態下控制目標不同的特點，在控制系統中設計了雙閉環反饋：焊接電壓反饋及焊接電流變化率di / dt反饋。
  3. The dcep mig has the characteristic of deeper penetration which can reduce defective fusion and good arc stabilization. the dcen mig has the characteristic of shallow penetration of welding seam, and the welding wire has a high melting speed. so the variable polarity pulsed mig is a new technology for the welding of aluminium alloy sheet

    變極性脈沖mig焊是一種新的焊接工藝方法，其綜合了dcep脈沖mig焊熔深較大、可以減少焊縫的熔合不良、電弧穩定性好和dcenmig焊焊縫熔深淺、焊絲熔化速度較快的特點，減小了焊縫的熔深，增加了焊絲的熔化速度，是一種適合於薄板鋁合金焊接的新方法。
  4. Heater adopts high quality stainless steel, alloy heating wire, electrical melting mgo powder etc. to make the heating elements after passing advanced technology such as coiling wire, shrinking tube, removing humidity and sealing etc. the connection between flange and heating tube adopts hydrogen arc welding and vacuum lead welding to guarantee the heater without leakage under high voltage

    加熱器採用優質不銹鋼管合金加熱絲電熔氧化鎂粉等材料，經繞絲縮管排潮封口等先進的生產工藝製造而成的發熱元件法蘭與電熱管的聯接採用氬弧焊及真空釬焊，保證了加熱器在高壓下的不滲漏。
  5. Specification for approval testing of welders when welding procedure approval is not required - tig or mig welding of aluminium and its alloys

    不要求批準焊接工藝時焊工的鑒定考試規范.第2部分:鋁及鋁合金鎢極惰性氣體保護電弧焊或熔化極惰性氣體保護電弧焊
  6. In this thesis, a set of control system is developed for igbt inverter power supply of consumable - electrode co2 shielded arc - welding machine

    本文為熔化極co2保護的igbt逆變半自動弧焊機電源研製了一套控制系統。
分享友人
分享到 Line

分享到臉書