Adopt advanced technic of f4 whole cold - press to moulding and heat melt to process to make, let the lining no slot to link withal cheek by jowl connect with exterior metalpipes wall, in the state of allowwing to work keep to distort in - phase, thereby to enhance using - life of lining in the working status of opposite high temperature high vacuum, stop the ecumenic pad fluorin pipes using in condition of cold and heat alternate and minus tension to come into being the matter of padding fluorin floor shrivel to jam the flowway and plastic rip, its perfect choice use to transport medium of strong corrosive strong oxidation by modern chemical - industry corporation
採用氟塑料f4整體冷壓成型及熱
熔加工等先進技術製造,使內襯層無縫搭接且與外層金屬管壁緊密粘接,在允許工作狀態下能夠保持同步變形,從而提高了襯里層在相對高溫高真空度的工況下的使用壽命,杜絕了一般襯氟管在冷熱交替,及負壓的條件下使用易產生襯塑層鼓癟阻
塞流道及塑料拉裂的問題,是現代化工企業在輸送強腐蝕強氧化介質理想的選擇。
Three way fuse plug
三線
熔絲
塞
Two way fuse plug
雙
熔絲插
塞
It shows with the increase of the amount of the mo in the si - mo infiltrant, the density of the infiltrated materials with the same performs increased, but the amount of the free carbon and pore also increased. it was the result of the capillary chocking - off caused by the separation of the mosj2 from the alloy infiltrant during the sintering process. after th thermal treatment at 2050, the amount of the free carbon and pore decreased. also. another cause for the unfully conversion of c into sic was the gas pressure. larger than the capillary force
實驗表明,對于同一坯體,隨著si - mo
熔體中mo含量的增加,浸滲所得材料的密度隨之增加,但是,材料中的殘留c 、氣孔相的含量亦隨之增加。這是由於反應浸滲時,
熔體中析出的mosi _ 2阻
塞毛細管造成的。含殘留c 、氣孔相的材料進行高溫( 2050 )熱處理后,材料中殘留c 、氣孔相的含量大大減少。
General type and load limiting type of constant filling fluid coupling. easy of dissolve plug
普通型限矩型液力偶合器.易
熔塞
Safety valves, gauges and fusible plugs for compressed air or inert gas installations - code of practice for installation
壓縮空氣或惰性氣體裝置用安全閥計量表和易
熔塞.第1部分:安裝實用規程
Teflon piston - ring integrated with piston, not only reduce the friction and noise, but also avoid inner - leakage
特氟龍材料的活
塞環與活
塞熔接成一體不僅減磨效果好,同時能減少噪音防止內泄。
" go " and " not go " plug gauges for d - type fuses ; gauges for edison thread
D型
熔斷器用過端和不過端
塞規.圓螺紋量規
The experiment result showed that, in the infiltration melting the evaporation speed of si is more rapid than mo. the melting which enrich the mo reacted with the sic body and there existed mo5si3c. the content of mosi2 can be controled by adjusting the contend of c in the perform ; the content of c is more high the pore volume in composite is more high
研究發現,由於
熔滲體中si的揮發速度快造成材料物相組成變化,
熔滲體與sic坯體反應析出mo _ 5si _ 3c 、 mo _ 5si _ 3相阻
塞坯體毛細管,使燒結體中產生氣孔。
Boiler plug alloy
鍋爐安全
塞合金
熔點在
For example, the enemies in utgarde keep ' s forge are there to craft weapons and armor for the vrykul to use in their war effort
比如說,烏特加德要塞熔爐區的敵人們正在為維京巨人的戰爭機器製造武器和護甲。