熔結劑 的英文怎麼說
中文拼音 [róngjiējì]
熔結劑
英文
agglomerant-
The imported transparent glaze fired at lower temperature was analysed semi - quantitatively by adopting emission spectroscope. the stripping of lead and cadmium from this transparent glaze fired at lower temperature in ceramic product was determined by atomic absorption spectroscope. the effect of chemical composition on the stripping of lead and cadmium was analysed. upon the author s opinion, the overproof lead stripping from the imported transparent glaze fired at lower temperature can only be settled by adopting lead - free glaze instead of adopting low - lead prescription. the author succeeded in developing an excellent lead - free transparent glaze fired at the lower temperature of 1000 1050. the success is based on an inquiry into the feasibility of using such new agents of fusion as li2o and sro in replacement of pbo ; and on a study of the effects of the contents of sio2 ， al2o3 ， b2o3and other metallic oxides on such performances of glaze as coefficient of linear expansion, fusion temperature and transparency. it is also based on an analysis of coefficient of linear expansion of blank and glaze on an analysis of coefficient of linear expansion of blank and glaze on their correlation ; and on a study of technology for preparing glaze
採用發射光譜儀對進口低溫透明釉進行半定量分析，並用原子吸收光譜儀測定其陶瓷製品的鉛、鎘的溶出量，分析化學成分對鉛、鎘溶出量的影響.結果表明，進口低溫透明釉採用低鉛配方不能解決鉛溶出量的超標問題，只有採用無鉛釉才能解決.探討用氧化鋰和氧化鍶等新型熔劑完全代替氧化鉛的工藝，研究釉料中氧化硅、氧化鋁、氧化硼和各種金屬氧化物的含量，對釉的線膨脹系數、熔融溫度和透明度等性能的影響.分析坯料、釉料的線膨脹系數及其相互關系和釉料制備的工藝，研製出優質的1000 1050低溫無鉛透明釉The technical requirements for the lost pattern made from the paraffin - stearin and the shell mould made from colloidal silica in the precision casting were introduced
摘要介紹用石蠟硬脂酸低溫模料製作熔模，用硅溶膠作粘結劑製造模殼的工藝。Melting point of nylon 11 blend alloy decreases as function of compatibilizer, and make clear that crystalline integrity of nylon 11 increases
尼龍11合金的熔點隨著相容劑的加入而降低，表明了其結晶的不完整性增加。A series of preparation conditions and parameters were systematically studied. it is concerned that the effects of prepared method of precursor, material synthesize method, fired atmosphere, fired temperature, fired time, flux kind and content, rare earth concentration and kind and matrix on the microstructure and optical storage properties of the samples. at the same time, the optical storage mechanism was discussed in certain extent
系統地研究了一系列的工藝條件及參數，討論了前驅物制備方法、材料合成方法、灼燒氣氛、灼燒溫度、灼燒時間、助熔劑種類及含量、稀土摻雜濃度及種類、基質成分對樣品微觀結構及光存儲性能的影響，同時對樣品的光存儲機理作了一定程度的探討。The results indicated that the dimension, shape and purity of base material could meet the functional demand of solid lubricant ; the thermal decomposition temperature of ptfe resin exceeds 400 c, but organic and inorganic packing filler added in ptfe made the water absorption rate of composite material increased, melting temperature and decomposition temperature decreased, in the meanwhile oxidative decomposition reaction was accompanied ; polar groups such as c = o, c - o - c and so on in the carbon fiber surface is advantageous to increase compatibility with other components and interlayer shearing strength ; uniform design experimental method could help to find the relationship between formula and frictional property by relatively small tests. the developing trend of each formula ' s friction coefficient could be showed by fitting curve ; the friction coefficient with no copper powder or graphite in formula was relatively big. this fact showed that copper powder and graphite should be used cooperatively ; it was found that when the ratio of copper powder to graphite by weight is 15 : 60, 30 : 30 - 40 and 60 : 15 - 30 respectively, the friction coefficient was relatively small. the degree of crystallinity of pure ptfe reached maximum by air cooling and the abrasion loss also reached maximum among three ones ; at the same time, the abrasion loss of solid lubricant sample was also the biggest among three ones ; when solid lubricant matched with 45 # steel axle or gcrl5 steel axle, lubricant transfer film could be formed on metal surface, thus direct contact between the surface of metal friction pair rings was reduced. their working life was elongated extremely ; there was mainly much graphite, a little ptff, moo3, feso4, cus and so on in lubricant transfer film
試驗結果表明：所選原料的尺寸、形狀及純度可滿足固體潤滑劑的性能要求；聚四氟乙烯樹脂熱分解溫度超過400 ，但在ptfe中加入無機填料會使復合材料吸水率提高，熔融溫度及分解溫度降低，且伴有氧化分解反應；碳纖維表面含有c = o及c - o - c等極性基團，有利於提高其與其它組分的相容性，提高層間剪切強度；均勻設計試驗方法能夠用較少的試驗次數找出配方與摩擦性能間的關系，擬合曲線基本能表示各配方的摩擦系數發展趨勢；配方中不加銅粉或不加石墨，其摩擦系數均較高，說明銅粉和石墨應該配合使用；當銅粉15份、石墨60份時，銅粉30份、石墨30 - 40份時，銅粉60 、石墨15 - 30份時，摩擦系數均具有較低值；純聚四氟乙烯樹脂在空氣冷卻時結晶度最大，磨損量也是三者中最大的；同時，固體潤滑劑試樣在空氣冷卻時的磨損量也是三者中最大的：不論是固體潤滑劑與45 #鋼軸配副或是固體潤滑劑鑲嵌入銅套后與gcr15鋼軸配副，在金屬表面均可形成潤滑轉移膜，從而減少金屬摩擦副表面間的直接接觸，大大延長其使用壽命;轉移膜中主要含有較多的石墨、少量聚四氟乙烯、 moo 。Rapid repairing mass for converter ismade of electro baked magnesite and high - quality synthetic sandand manufactured by adding high fluidity recarburizer ( beveloped by ourselves ) as addition agent withspecial technique. lt has the characteristics of well fluidity, well rapid fluidityand rpid sintering etc. it is applied to hot patching of large area before or after the converter as rapping hole patching and other parts for converter
轉爐快速補爐料是以電熔鎂砂和優質合成砂為主要原料，配以自行研製的高流動性的增碳劑為添加劑，以特殊工藝生產製成，具有流動性好、快速燒結等特點，適合於轉爐的前後大面的熱修補及出鋼口等部位的修補Experimental results show that the order of fluoride salt being put in and flux type also influences the phases constitution, morphology, distribution and absorbent rate of ti and b. the experiments on remelting master alloys and al or al alloys at a certain temperature range show that the phases constitution and size have a remarkable heredity
試驗結果表明，不同的氟鹽加入順序和熔劑種類的不同也直接影響著中間合金中化合物的相組成、形態、分佈以及中間合金中ti 、 b的實收率等。在用純鈦顆粒法制備中間合金時，熔煉溫度的改變只能影響tial _ 3晶體的尺寸大小，而無法改變其形態。The product is manufactured by taking high purity fused magnesia as raw material and adding a special binder, sintering agent and coagutant through a special production process
該產品是以優質高純電熔鎂砂為主要原料，外加特殊結合劑、燒結劑、促凝劑，經過特殊的生產工藝加工而成。Baseing on the request of low coercivity and high squareness in application, we had confirmed the main formulation of the lizn ferrite ; during the study of the conventional ceramic process, with the main formula foundation, we mainly studied the influence of ti4 +, co3 + on lowering coercivity and bi2o3, v2o5 on lowering sinter temperature. the results showed bi2o3 good characteristic on lowering sinter temperature and the sample which mixed with 1 % bi2o3 could reduce 40 % coercivity through slowing heating rate and extending the holding time
在氧化物陶瓷工藝技術研究中，按實際應用中低矯頑力、高矩形比的要求，確定了lizn鐵氧體的主配方，在主配方基礎上進行了ti4 + 、 co3 +等離子對降低矯頑力的研究以及添加bi2o3 、 v2o5助熔劑對降低燒結溫度的研究，發現bi2o3具有優良的降低燒結溫度的特性，在添加bi2o3樣品燒結過程中，降低升溫速率，延長保溫時間可以降低40 %左右的矯頑力。Extraction of large - fragment genomic dna in order to gain dna template of pcr amplification ( long pcr amplification and salvage pcr amplification ) which was high purity and large fragment, three methods were used to extract genomic dna of bacillus subtilis, i. e. low melting - point agarose embedding method, sds - proteinase k - phenol chloroform extraction method and bacterial genomic dna extraction kit method. the genomic dna of bacillus subtilis were gained by these methods, and the operated programs of the methods were improved. the results showed that the genomic dna extracted by low melting - point agarose embedding method were obviously biggest than that of another two methods
大片段基因組dna的提取為了獲得用於pcr擴增（長距離pcr擴增和分段pcr擴增）的高純度、大片段（至少為pcr產物長度的4倍）的dna模板，應用三種方法：低熔點瓊脂糖包埋法， sds -蛋白酶k -酚氯仿抽提法和細菌基因組dna提取試劑盒法，分別提取獲得了枯草桿菌基因組dna ，並對3種方法的操作程序進行了不同程度的改進，結果表明：低熔點瓊脂糖包埋法提取的基因組dna片段明顯大於后兩種方法，採用0 . 5瓊脂糖凝膠電泳3h ，仍然跑不出加樣孔。Study on the optical properties of transparent epoxy / clay nanocomposites a new type transparent epoxy based nanocomposites has been prepared by the reaction of alkylammonium exchanged montmorillonite ( amt ) with diglycidyl ether of bisphenol a ( dgeba ) and triethylamine as the curing agent. the morphology of amt in the epoxy matrix was characterized with x - ray diffraction ( xrd ), scanning electron microscopy ( sem ) and transmission electron microscopy ( tem )
光學透明環氧樹脂粘土納米復合材料光學性能採用十八烷基伯胺鹽、十六烷基三甲基溴化胺處理na基蒙脫土製備出兩種不同的有機土，以三乙胺為固化劑，有機土與雙酚a型環氧樹脂熔融插層聚合后制備出剝離型和插層型兩種結構的環氧樹脂粘土納米復合材料。The effect of h3bo3 was discussed in detail, and the luminescence and aferglow time was increased. the stability of this material was studied and it needs coating processing in application. then by changing the base, activator, flux and reaction condition, we studied different phosphors based on the aluminates, silicates, catio3 and y2o2s in detail, and obtained the best stoichiometry and preparation of these phosphors with the colors of red, red and orange, yellow - green, blue - green, cyan and blue - purple
本論文採用高溫固相法，對黃綠色sral _ 2o _ 4 ； eu ， dy長余輝材料的發光特性進行了深入的研究，詳細討論了助熔劑硼酸對材料的影響，大幅度提高了該材料的余輝亮度和時間，並對該材料的穩定性進行了研究，得出使用時要進行包膜或其他防潮處理的結論。In this paper the formula, the technics, the dosage of the filler and the macromolecule coupling agent are studied which influence the technics condition, mechanical properties, structure configuration. also x - ray large angle diffraction, scan electron microscope, dta etc are used to analysis and test the properties of the pp / talc composites. conclusions as follows : 1
本文系統地研究了復合體系配方、工藝方法、填料及偶聯劑用量對復合體系工藝條件、力學性能及結構形態的影響，同時利用廣角x射線衍射、掃描電鏡、 dta等對復合體系的性能進行了測試與分析，主要研究內容及結論如下： 1滑石粉的加入，雖然使pp的熔化時間增加，但是混煉能耗下降，有利於pp的加工；偶聯劑的加入，使pp的熔化時間增加，能耗略有降低，總體而言，對加工無不利影響。This paper is mainly concerned about how to purify the industrial products of the antioxidant d and bht, how to determine their purities, determining their purities and the purities need to be more than 99 %. in order to attain this objective, the recrystalizing method is used to purify antioxidant d and antioxidant bht. the methods of high performance liquid chromatography ( hplc ) is used to determine the chemical composition of the antioxidant d and bht, it is qualitative analysis
本論文是以防老劑d與bht工業品為主要原料制備防老劑d與bht標準物質，首先進行了防老劑d與bht的提純和熔點的測定試驗，並通過實驗確定了防老劑d與bht重結晶提純工藝；然後設計區域熔融裝置，擬定操作規程和技術條件，通過用區域熔融法提純重結晶后的防老劑d和bht產品滿足標準物質的純度要求。Differential scanning calorimeter ( dsc ) combined with melt fluxing technique was used to realize undercooling of melt and its specific heat was measured at the same time, and its thermodynamics were calculated simultaneously and compared to four well - known models
本文將差示掃描量熱法（ dsc ）和助熔劑處理技術相結合，研究了熔體的過冷現象，測量了過冷狀態下熔體的比熱，計算了過冷熔體凝固過程中的其它熱力學參數，並與四種近似模型進行了比較分析。They have excellent corrosion, thermal shock resistance and spalling resistance. they wide applications and can be used in key locations of thermal processing equipment such as bof, eaf, lf and so on. 2 alumina - magnesia - carbon brick made from high - purity bauxite or fused alumina and fused magnesia grain or high purity magnesia by pressing, resin - bond for thermal shock resistance
1 ，鎂碳磚是不燒的耐火材料，經過摩擦壓磚機的成型以及乾燥處理后而成，它的主要原料是電熔鎂，高純鎂砂和高純石墨，結合劑為樹脂，鎂碳磚有良好的耐侵蝕性，熱震穩定性和抗剝落性，它已經被廣泛地用在鋼廠的轉爐電爐鋼包精煉鋼包等關鍵部位。Test method for properties of investment casting pattern materials - part 6 : determination of wetting angle between pattern an binder
熔模鑄造模料性能試驗方法第7部分:熔模-粘結劑潤濕角的測定Additions of carbon for improved slag resistance. spinel formation improves hot strength, slag resistance and brick joint erosion. 3 repairing material for bof uses fused magnesia or sintered magnesia as the main raw material and after modifid pitch and special additives are added, it has the following characteristcs than other conventional converter pitch temperature, shorter sintering time, longer service life and less pollution. it is mainly used for repairing converter working face, also for tapping side, tapping hole and bottom
3 ，轉爐大面補料是採用電熔鎂砂或燒結鎂砂為主要原料，通過加入改性瀝青和特種添加劑使它和傳統瀝青補爐料相比具有高溫附著性好燒結時間短流動性好使用壽命長污染小等特點，主要用於修補轉爐迎鋼面通常稱「大面」也可以用於修補出鋼側，出鋼口及爐底等部位。The results of e - o tests showed that ktp crystals by our flux technique is an attractive material for various e - o applications, especially used in a high - repetition - rate and high responsible laser system
電光應用試驗結果表明，本實驗的熔劑法ktp晶體是一種非常吸引人的電光材料，特別是適合用於高重復頻率、高響應速度等激光系統。Results the experiment manifested that the compensator fabricated by the way could make the high dosage shape of target in accordance with the form of tumor and could adjust the distribution of the dosage according to remedy requirement
結果：實驗和研究表明，運用該方法製作的三維熔鉛調強擋塊，不僅能實現靶區高劑量的形狀在三維方向上與腫瘤的形狀一致，而且可時照射野內劑量分佈按要求的方式調整。分享友人