熔解系數 的英文怎麼說
中文拼音 [róngjiěxìshǔ]
熔解系數
英文
flux factor-
The imported transparent glaze fired at lower temperature was analysed semi - quantitatively by adopting emission spectroscope. the stripping of lead and cadmium from this transparent glaze fired at lower temperature in ceramic product was determined by atomic absorption spectroscope. the effect of chemical composition on the stripping of lead and cadmium was analysed. upon the author s opinion, the overproof lead stripping from the imported transparent glaze fired at lower temperature can only be settled by adopting lead - free glaze instead of adopting low - lead prescription. the author succeeded in developing an excellent lead - free transparent glaze fired at the lower temperature of 1000 1050. the success is based on an inquiry into the feasibility of using such new agents of fusion as li2o and sro in replacement of pbo ; and on a study of the effects of the contents of sio2 ， al2o3 ， b2o3and other metallic oxides on such performances of glaze as coefficient of linear expansion, fusion temperature and transparency. it is also based on an analysis of coefficient of linear expansion of blank and glaze on an analysis of coefficient of linear expansion of blank and glaze on their correlation ; and on a study of technology for preparing glaze
採用發射光譜儀對進口低溫透明釉進行半定量分析，並用原子吸收光譜儀測定其陶瓷製品的鉛、鎘的溶出量，分析化學成分對鉛、鎘溶出量的影響.結果表明，進口低溫透明釉採用低鉛配方不能解決鉛溶出量的超標問題，只有採用無鉛釉才能解決.探討用氧化鋰和氧化鍶等新型熔劑完全代替氧化鉛的工藝，研究釉料中氧化硅、氧化鋁、氧化硼和各種金屬氧化物的含量，對釉的線膨脹系數、熔融溫度和透明度等性能的影響.分析坯料、釉料的線膨脹系數及其相互關系和釉料制備的工藝，研製出優質的1000 1050低溫無鉛透明釉The results indicated that the dimension, shape and purity of base material could meet the functional demand of solid lubricant ; the thermal decomposition temperature of ptfe resin exceeds 400 c, but organic and inorganic packing filler added in ptfe made the water absorption rate of composite material increased, melting temperature and decomposition temperature decreased, in the meanwhile oxidative decomposition reaction was accompanied ; polar groups such as c = o, c - o - c and so on in the carbon fiber surface is advantageous to increase compatibility with other components and interlayer shearing strength ; uniform design experimental method could help to find the relationship between formula and frictional property by relatively small tests. the developing trend of each formula ' s friction coefficient could be showed by fitting curve ; the friction coefficient with no copper powder or graphite in formula was relatively big. this fact showed that copper powder and graphite should be used cooperatively ; it was found that when the ratio of copper powder to graphite by weight is 15 : 60, 30 : 30 - 40 and 60 : 15 - 30 respectively, the friction coefficient was relatively small. the degree of crystallinity of pure ptfe reached maximum by air cooling and the abrasion loss also reached maximum among three ones ; at the same time, the abrasion loss of solid lubricant sample was also the biggest among three ones ; when solid lubricant matched with 45 # steel axle or gcrl5 steel axle, lubricant transfer film could be formed on metal surface, thus direct contact between the surface of metal friction pair rings was reduced. their working life was elongated extremely ; there was mainly much graphite, a little ptff, moo3, feso4, cus and so on in lubricant transfer film
試驗結果表明：所選原料的尺寸、形狀及純度可滿足固體潤滑劑的性能要求；聚四氟乙烯樹脂熱分解溫度超過400 ，但在ptfe中加入無機填料會使復合材料吸水率提高，熔融溫度及分解溫度降低，且伴有氧化分解反應；碳纖維表面含有c = o及c - o - c等極性基團，有利於提高其與其它組分的相容性，提高層間剪切強度；均勻設計試驗方法能夠用較少的試驗次數找出配方與摩擦性能間的關系，擬合曲線基本能表示各配方的摩擦系數發展趨勢；配方中不加銅粉或不加石墨，其摩擦系數均較高，說明銅粉和石墨應該配合使用；當銅粉15份、石墨60份時，銅粉30份、石墨30 - 40份時，銅粉60 、石墨15 - 30份時，摩擦系數均具有較低值；純聚四氟乙烯樹脂在空氣冷卻時結晶度最大，磨損量也是三者中最大的；同時，固體潤滑劑試樣在空氣冷卻時的磨損量也是三者中最大的：不論是固體潤滑劑與45 #鋼軸配副或是固體潤滑劑鑲嵌入銅套后與gcr15鋼軸配副，在金屬表面均可形成潤滑轉移膜，從而減少金屬摩擦副表面間的直接接觸，大大延長其使用壽命;轉移膜中主要含有較多的石墨、少量聚四氟乙烯、 moo 。In the beginning, the development history and the current development of the technique of fiber detection are introduced briefly. then, discussed in detail are strong coupling theory concerning the fbt coupler and the weak coupling theory concerning the hf acid etching and the side - polishing coupler. from the analysis of fiber coupling equations, the solution of the equation and the formula of the coupling coefficient are derived
本文首先概述了光纖竊聽技術的發展歷程和現狀，有針對性地分析了關于光纖竊聽技術中的光纖耦合問題，並詳細介紹了用於熔融拉錐耦合器的強耦合理論和用於氫氟酸腐蝕與邊研磨光纖耦合器的弱耦合理論;分析了耦合模方程，得出了耦合模方程的形式解，推導出耦合系數的計算公式。Abstract : according to characters of different research ways, the research development of thermodynamic models of metallic melts is systematically introduced, such as solution model method, geometrical model method, interaction coefficient method, analytical method and experienced model method
文摘:根據不同研究方法的特點，綜述了溶液模型法、幾何模型法、相互作用系數法、解析計演算法以及經驗模型法等金屬熔體熱力學模型的研究進展，並對這些方法進行了簡要的評述。分享友人