熱接片法 的英文怎麼說
中文拼音 [rèjiēpiānfǎ]
熱接片法
英文
hot splice-
The welding technology of francis turbine runners is optimized from the view of subsection welding and local heating by numerical simulation. the result shows that welding residual tensile stress appears in the weld and its area nearby, and peak stress appears in the dangerous area of blades after practising quondam welding technology ; welding residual tensile peak stress in the dangerous area of blades can be decreased by welding both ends earlier and then welding middle section later during subsection welding, and decreasing effect on welding residual stress of the subsection welding is related to the weld length of blade outlets and welding direction of each subsection ; decreasing effect on residual stress of the local heating is direct proportional to heating time, heating temperature, heating area, and inversely proportional to cooling area, and welding residual tensile peak stress in the dangerous area is decreasing trend earlier, and then increasing trend later with heated location increased
本文利用數值模擬手段對轉輪的焊接工藝從分段焊和局部加熱兩個方面進行了優化，結果表明:採用普通工藝焊接時，葉片焊后殘余拉應力出現在焊縫及其附近區域，並且在葉片出水邊的熔合線附近（危險區域）出現了峰值;在採用優化的分段焊時，先焊兩端后焊中間的方法可以降低葉片危險區域的焊接殘余拉應力峰值，降低效果與葉片出水邊焊段長度、焊縫各段的焊接方向有關;局部加熱法降低轉輪危險區域殘余應力的效果主要與加熱時間、加熱溫度以及加熱面積成正比，與冷卻面積成反比，並且危險區域的殘余應力隨加熱區域的增大呈先降低后升高的趨勢。The tlow distance and gelating time of the nanocomposites were shorter than that of the pure pf, which meet the standard of the pf used in frictional materials. compared to the pure pf, the silica7pf nanocomposites exhibited excellent heat stability only in nitrogen atmosphere, however, so do vermiculite / pf nanocomposites in both nitrogen and air atmospheres. compared to the brake pad based pf resin, the wear rate of the present one based with silica / pf nanocomposite decreased obviously, especially in high temperature
用烷基銨ctab和kh - 560對蛭石進行有機化處理，通過原位聚合法制備了酚醛樹脂接枝改性sio _ 2納米復合材料、酚醛樹脂kh - 560改性sio _ 2納米復合材料、酚醛樹脂ctab改性蛭石納米復合材料、酚醛樹脂/ kh . 560改性蛭石納米復合材料，採用ftir 、 xrd 、 afm和tg分析與流動距離、凝膠化時間的測試，研究了所制備的酚醛樹酯納米復合材料的結構、固化行為和熱穩定性能，並研究了以酚醛樹酯納米復合材料為基體的剎車片摩擦磨損性能。Silicon nitride ( normally si3n4 ) has been widely used in such fields as micro - electronics and optoelectronics as a promising film material because of its excellent property. many researches have been made on silicon nitride, especially on preparation for it with all kinds of cvd ( chemical vapor deposition ). but the growth mechanism and kinetics of direct - nitridation in nitrogen are not investigated in detail, especially few work has been done on direct - nitridation of silicon wafer in nitrogen during heat treatment
氮化硅（ si _ 3n _ 4 ）具有許多特殊的優越性能，是一種前景廣闊的薄膜材料，並已廣泛應用於微電子、光電子領域，人們對此做了大量的研究，但主要集中在用各種化學氣相沉積的薄膜制備上，對直接氮化法的機理和動力學研究較少，特別是矽片在氮氣保護的熱處理條件下的直接氮化行為研究更少，甚至對矽片在熱處理條件下能否與惰性的氮氣發生反應等問題依然存在爭論。On - line monitoring of hvcb is the precondition of predicting maintenance, is the key element of reliable run, and is the important supplement to the traditional off - line preventive maintenance in fact, the faults are made by hvcb, no matter in number or in times, is over 60 % of total faults so it has determinative importance for improving the reliability of power supply and this can greatly decrease the capital waste used by - dating overhaul in this paper, the inspecting way of hvcb mechanism characteristic is discussed the concept of sub - circuit protector is presented, the scheme that we offered has been combined with sub - circuit integrality monitoring theory, to ensure that it has the two functions as a whole according the shut - off times at rated short circuit given by hvcb manufacturer, the electricity longevity loss can be calculated in each operation, and the remained longevity can be forecast too an indirect way for calculating main touch ' s temperature by using breaker shell temperature, air circumference temperature and breaker ' s heat resistance is improved in this paper, and main touch resistance can be calculated if providing the load current msp430, a new single chip microcomputer made by ti company, is engaged to develop the hardware system of the on - line monitoring device, and special problem brought by the lower supply voltage range of this chip is considered fully
高壓斷路器所造成的事故無論是在次數，還是在事故所造成的停電時間上都占據總量60以上。因此，及時了解斷路器的工作狀態對提高供電可靠性有決定性意義；並可以大大減少盲目定期檢修帶來的資金浪費。本文論述了斷路器機械特性參數監測方法；提出了二次迴路保護器的概念，並將跳、合閘線圈完整性監視和二次迴路保護結合起來，給出具有完整性監視功能的二次迴路保護器實現方案；根據斷路器生產廠家提供的斷路器額定短路電流分斷次數，計算每次分閘對應的觸頭電壽命損耗，預測觸頭電壽命；提出根據斷路器殼體溫度和斷路器周圍空氣溫度結合斷路器熱阻來計算斷路器主觸頭穩態溫升的方法，並根據此時的負荷電流間接計算主觸頭迴路的電阻；在硬體電路設計上，採用美國ti公司最新推出的一種功能強大的單片機msp430 ，並充分考慮該晶元的適用電壓范圍給設計帶來的特殊問題；在通信模塊的設計中，解決了不同工作電壓晶元之間的介面問題，並給出了直接聯接的接線方案。分享友人