熱模塑 的英文怎麼說
中文拼音 [rèmósù]-
Specification for steel, sheet and strip, heavy thickness coils, hot rolled, carbon, structural, high - strength low - alloy, columbium or vanadium, and high - strength low - alloy with improved formability
片鋼和帶鋼厚卷材熱軋高強度低合金結構碳鋼以及改良可模塑高強度鈳或釩低合金鋼規范Moulded polystyrene foam board for thermal insulation
絕熱用模塑聚苯乙烯泡沫塑料Note the compression condition may be difference, because the shape, dimension, and usage of produce were difference, the condition adjustment must under the premise that did not reduce the product quality
注:模塑料預熱后,須在模具中合模20 - 40秒後排氣再加壓。With the focus on the structure and components character of plate metal / ceramics graded coating, this paper extends and improves the thermal elastoplastic analysis model of trilayered materials derived by suresh et al and builds the theoretical model of thermal elastoplastic stresses analysis of plate metal / ceramics graded coating, and this paper also analyzes the thermal elastoplastic stresses and deformation of metal / ceramics graded coating
本文針對平板狀金屬陶瓷梯度塗層的結構和組成特徵,推廣和完善了suresh等人的三疊層材料的熱彈塑性分析模型,建立了平板狀金屬陶瓷梯度塗層熱彈塑性應力分析的理論模型,對金屬陶瓷梯度塗層的熱彈塑性應力和熱彈塑性變形進行了分析。This paper also researches on thermal elastoplastic analysis model of multilayered graded coating structures on the basis of thermal elastoplastic analysis model of trilayered materials with the focus on the structural character of graded coating. it builds the thermal elastoplastic analysis theory for the graded coating structure that has a single plastic layer or two plastic layers. it gives the analytical formulas of thermal stresses and the thermal elastic - plastic transform temperatures of graded coating that has a single plastic layer or two layers under the thermal loading
針對梯度塗層的結構特徵,在建立的三層疊層材料熱彈塑性分析模型的基礎上,對多層梯度塗層結構的熱彈塑性分析模型進行了研究,分別建立了含單個塑性層和兩個塑性層的梯度塗層結構的熱彈塑性分析理論,給出了在熱載荷作用下含單個塑性層和兩個塑性層的梯度塗層的熱彈性-塑性臨界溫度和熱應力分析公式,利用有限元分析對理論模型進行了驗證。This paper firstly extends the thermal elastoplastic deformation theory of trilayered materials derived by suresh et al and abolishes the restrictive assumption to the monodirectional spread of plastic zone in the original model and the thermal elastoplastic analysis model which reflects the complete history of thermal elastoplastic deformation of the multilayered materials is built. this model can be also applied to the condition of the spread of plastic zones from both sides of plastic layers and has more applicability compared to suresh et al ' s model
論文首先推廣了suresh等人建立的三疊層材料熱彈塑性變形理論,取消了原理論模型中塑性區域單向擴展的限制性假設,建立了反映疊層材料完整熱彈塑性變形歷史的熱彈塑性行為分析模型,該模型同時適用於塑性層的塑性區域雙邊擴展的情況,較suresh等人的模型適用性更為廣泛。Electrical insulating materials - methods of test for the hydrolytic stability - part 2 : moulded thermosets
電絕緣材料.水解穩定性的試驗方法.第2部分:熱模塑法Electrical insulating materials. methods of test for the hydrolytic stability. part 2 : moulded thermosets
電絕緣材料.水解穩定性試驗方法.第2部分:模製熱固塑料Thermoplastics piping systems. non - end - load - bearing elastomeric sealing ring type joints between pressure pipes and moulded fittings. test method for leakightness under internal hydrostatic pressure without end thrust
熱塑料管道系統.壓力管和模塑配件的合成橡膠密封環型接合.在無軸向推力時內部流體靜力學壓力下密封性試驗方法Specification for moulded thermoplastics dustbins excluding lids
模塑熱塑性塑料吸塵箱Tertm thermal - expansion resin transfer molding
熱膨脹樹脂傳遞模塑Research and development progress in modified phenolic resin used for friction materials
聚碸改性酚醛樹脂玻纖增強模塑料的熱老化研究08. 02 test method for spiral flow of low - pressure thermosetting molding compounds
低壓熱固性模塑料的螺線流動度的試驗方法En iso 12115 fibre - reinforced plastics. thermosetting moulding compounds and prepregs. determination of flowability and shelf life
纖維增強塑料.熱固模塑混合物和預浸料.流動性和貯藏壽命測定Standard classification system for thermoplastic elastomer - ether - ester molding and extrusion materials
熱塑性彈性醚酯模塑和擠制材料的標準分類體系Plastics - thermoplastic polyester ester and polyether ester elastomers for moulding and extrusion - part 1 : designation system and basis for specifications
塑料.模塑件和擠塑件用熱塑性聚酯酯和聚醚酯彈性體.第1部分:名稱體系和規范基礎Plastics - thermoplastic polyester ester and polyether ester elastomers for moulding and extrusion - part 2 : preparation of test specimens and determination of properties
塑料.模塑件和擠塑件用熱塑性聚酯酯和聚醚酯彈性體.第2部分:試樣的制備和性能的測定Practice for compression molding test specimens of thermosetting molding compounds
熱固性模塑化合物壓縮模塑樣品的實施規程Testing of plastics ; boiling test of moulded articles made of thermosetting moulding materials
塑料的檢驗.熱固性模塑材料模壓製品的煮沸試驗Standard practice for injection molding test specimens of thermoplastic molding and extrusion materials
熱模塑和擠塑材料的噴射模塑法試樣標準規程分享友人