熱硬結性樹脂 的英文怎麼說
中文拼音 [rèyìngjiēxìngshùzhī]
熱硬結性樹脂
英文
thermosetting resin- 硬 : 形容詞1 （堅硬） hard; stiff; tough 2 （剛強; 堅定; 強硬） strong; firm; tough; obstinate 3 （勉...
- 結 : 結動詞（長出果實或種子） bear （fruit）; form （seed）
- 性 : Ⅰ名詞1 （性格） nature; character; disposition 2 （性能; 性質） property; quality 3 （性別） sex ...
- 樹 : Ⅰ名詞1 （木本植物的通稱） tree 2 （姓氏） a surname Ⅱ動詞1 （種植; 栽培） plant; cultivate 2 （樹...
- 脂 : 名詞1. （動植物所含的油質） fat; grease; tallow 2. （胭脂） rouge 3. （姓氏） a surname
- 樹脂 : resin; jaffaite; peucine
-
The degrees of crystallinity of pure ptfe under the different conditions of water cooling, air cooling and furnace - varying cooling were made comparison by xrd. the thermal stability of pure ptfe and solid lubricant was analyzed by dsc - tg ; the composition and valence state of elements in the surface of carbon fiber, solid lubricant before and after friction test and lubricant transfer film were characterized by xps ; the frictional property of solid lubricant was tested by pin and disk test rig. the frictional wear property of solid lubricant between embedded bearing sleeve and steel axle friction pair ring was tested by special simulate test machine, the hardness of solid lubricant was tested by pm ; the compression strength of solid lubricant was tested by material test machine
用sem表徵原料微觀結構、摩擦表面及潤滑轉移膜表面形貌：用xrd進行原料物相分析，及比較水冷卻、空氣冷卻、隨爐冷卻三種工藝條件下的純聚四氟乙烯樹脂的結晶度；用dsc - tg分析純聚四氟乙烯樹脂及固體潤滑劑的熱穩定性；用xps表徵碳纖維表面、固體潤滑劑摩擦前後表面、潤滑轉移膜表面的元素組成、價態變化；用銷盤式摩擦磨損試驗機對固體潤滑劑進行摩擦性能測試；採用專用的臺架模擬試驗機對固體潤滑劑鑲嵌軸承套與鋼軸摩擦副間的摩擦磨損性能進行測定；用萊次偏光顯微鏡（ pm ）測試固體潤滑劑的硬度；用材料試驗機測試固體潤滑劑的抗壓強度等。Performance for a piezoresistive transducer pressure sensor to thermal and pressure environments can be predicted by finite element method. a simplified 1 / 8 model, considering silicon dioxide and nitride process as well as stack anodic bonding and adhesive bonding processes, was developed. the fem results were found to be comparable to experimental data. case studies suggested that pyrex stack induces certain amount of non - linearity, while it isolates hard epoxy nonlinear effect. flexible epoxy bonding or soft adhesive bonding is preferred to the packaging process. the viscoelasticity and viscoplasticity of bonding material will result in hysteresis and drift errors to sensor output. however, soft adhesive s influence on sensor can be ignored under relative stable environments. more over, detailed design and process information will help to improve modeling application
熱、壓環境下壓阻變換壓力傳感器的性能可以通過有限元方法預測.這里研究了簡化的1 / 8模型，模型考慮了二氧化硅和氮化硅生成過程及堆陽極鍵合和膠粘結合過程.結果發現有限元預測結果和實驗數據具有可比性.範例研究表明，硼硅堆導致產生一定的非線性，但它隔離了硬環氧樹脂的非線性.在包裝過程中最好使用柔性環氧黏合或軟黏膠性結合.黏合材料的黏彈性和黏塑性將會導致傳感器輸出的滯后和漂移誤差.然而，在相對穩定的環境下，軟黏合劑對傳感器的影響可以忽略.此外，詳細的設計和過程信息有助於提高模型的適用性
分享友人