燒成強度 的英文怎麼說

中文拼音 [shāochéngqiángdù]
燒成強度 英文
fire strength
  • 燒 : Ⅰ動詞1 （使東西著火） burn 2 （加熱或接觸某些化學藥品、放射性物質等使物體起變化） cook; bake; hea...
  • 成 : Ⅰ動詞1 （完成; 成功） accomplish; succeed 2 （成為; 變為） become; turn into 3 （成全） help comp...
  • 強 : 強形容詞（強硬不屈;固執） stubborn; unyielding
  • 度 : 度動詞[書面語] （推測; 估計） surmise; estimate
  • 燒成 : baking
  1. Results show that : ( 1 ) for each particle size of andalusite, variation tendency of the properties of the material is generally the same : the maximum of bulk density, compressive strength and rupture strength appears in the range of 5 % - 10 % content of fiber, these properties of the material remarkably decrease as the fiber content exceed 10 % ; while at the same fiber content, the properties of the material increase with the increase of firing temperature

    結果表明： （ 1 ）對于不同粒度的原料，性能變化規律大致相同：在同一燒成溫度下，體積密度、常溫耐壓強度、常溫抗折強度在5 10之間出現峰值，加入量超過10之後材料的性能明顯下降；在相同的纖維含量下，隨著燒成溫度的提高，試樣的各項性能均有所上升。
  2. The material was sintered at 1050 for three hours to get the porous artificial bone, that its apparent porosity was54 %, its volume density was 1. 28 g / cm3, and its bending strength was 13. 25mpa. the results showed that the sintering temperature was reduced by adding bioglass

    本研究採用含生物玻璃前驅體粉末原料，添加檸檬酸造孔劑，模壓成型，在1050燒結保溫3小時，獲得了顯氣孔率為54 、體積密度為1 . 28s cm ~ 3 、抗彎強度為13 . 25mpa的多孔hap人工骨材料。
  3. To meet the processing requirements before sintering, the pressed briquet was pre - calcined at 1150 to make it possess adequate processing strength at first and then was shaped through precise turning on the numerical control lathe according to the design diagram of the femoral head prostheses of partial hip joint

    為滿足燒結前坯體加工的要求，壓制后的坯體在1150預燒，使其具備一定的加工強度，然後按照半髖關節股骨頭假體的形狀尺寸設計圖在數控車床上進行精密車削成型。
  4. When the alumina fiber accounted for 10 %, the density of the composites was chiefly high and the fiber evulsion effect was reinforced ; when the alumina fiber accounted for 30 %, the fiber evulsion effect, fracture and bridge - connection effect were mainly strengthened, when the fiber proportion was 50 %, at the temperature of 1500 c, the bending strength reached 26. 11 mpa while the compressive strength was 79. 30 mpa

    氧化鋁纖維含量為10和30的試樣增強機理不同，含量為10時，復合材料以基質密實度高、纖維拔出效應增強為主；氧化鋁纖維含量為30時，復合材料以纖維拔出、斷裂、橋聯效應增強為主。當纖維含量為50時，在1500下燒成，其抗折強度達到26 . 11mpa ，耐壓強度達到79 . 30mpa ，該復合材料可用作輕質保溫材料。
  5. The studies indicate that different content of pyrophyllite and dolomite can cause the following three cases : ( 1 ) making the refractory point decrease linearly and, to some extent, influencing the microstructure and properties of sintered body ; ( 2 ) acceleratingmullite formation during sintering, reducing thermal expansion coefficient of bond, reinforcing the matching nature and improving the flexural strength and shock strength ; ( 3 ) preventing sic grinding tool from generating black core, expanding suitable sintering temperature range of sic grinding tool

    同時，也不同程度地影響了磨具燒結體的微觀結構和性能； （ 2 ）可促進在燒結過程中莫來石的形成，降低結合劑的熱膨脹系數，加強了結合劑與磨料的匹配性，提高了磨具的抗折強度和抗沖擊強度； （ 3 ）在一定溫度范圍內還可防止碳化硅磨具出現黑心現象，拓寬了碳化硅磨具的燒結溫度適應范圍。
  6. ( 1 ) how to prefabricate mullite whisker formed in - site to enhance ceramics intensity, improve thermal - shock resistance by adoption zirconate and alumina to sinter mullite / zirconia / alumina composite ceramics. ( 2 ) studying on the plasticity of high alumina body materials

    利用氧化鋁、鋯英石原料燒成氧化鋁氧化鋯莫來石復合陶瓷，通過原位生成莫來石晶須提高載體的強度、改善其抗熱震性。
  7. The activatory coal gangue powder ( acgp ), ground cement clinker and natural gypsum are mixed by different ratios to prepare blended cement specimens, and its mortar compressive strength performance, water usage for standard consistency, and flowability of mortar are investigated

    摘要將經燃燒等過程進行活化處理的煤矸石細粉與磨至一定比表面積的水泥熟料及天然生石膏混合均勻，製成了活化謀矸石粉摻量比例不同的多組混合水泥，並對其膠砂強度性能、標準稠度用水量、膠砂流動度進行了實驗檢測。
  8. The influence of burning system on the properties and structure of the ceramic capacitors has been studied under the certain temperature system, the optimum sintering temperature of the ceramics was primarily decided by the content of bi2o3 ? 3tio2. the sintering temperature dropped with the adding of bi2o3 ? 3tio2. at the range of suitable sintering temperature, slow heating and low temperature sintering can obtain fine grain and dense structure. it results in the improving of the breakdown voltage for the middle - high voltage ceramic capacitors

    研究了燒成工藝制度對電容器陶瓷性能和結構的影響，結果表明：在一定的升溫保溫時間下，瓷料的最佳燒結溫度主要取決于組成中bi _ 2o _ 3 ? 3tio _ 2的含量， bi _ 2o _ 3 ? 3tio _ 2含量的增加將降低燒結溫度；在合理的燒結溫度范圍內，慢速升溫和低溫燒結將有利於得到細晶緻密結構，從而改善中高壓陶瓷電容器的耐壓強度。
  9. It is indicated that since different kinds of iron ores have different self - characteristics, the sintering intensity of binding phase and its dependence on basicity have obvious difference

    結果表明：不同種類的鐵礦粉由於其自身特性的不同，所生成的燒結粘結相的強度以及隨二元堿度的變化規律有明顯差異。
  10. Examination of the density, strength, hardness and microstructure showed that the mechanical properties and structure of the part made by direct metal forming process are better than that obtained from selective laser sintering process, as good as or even better than castings

    對成形件進行的密度、強度和硬度指標測試和金相組織觀察表明：基於弧焊的直接金屬成形件的組織結構和力學性能指標明顯優于選擇性激光燒結工藝成形件，達到或高於鑄造零件。
  11. But it also includes two fatal disadvantages : first, at is difficult to be sintered and its density is low, which causes its lower strength ; second, in the temperature range of 1023 - 15 73 k, at can decompose into al2o3 and tio2 easily, which can cause the stress concentrated and raise the heat expansion rate

    但是該材料本身存在的兩大致命的缺點，在很大程度上限制了它的廣泛應用： （ 1 ） 、鈦酸鋁難以燒結，燒結體的緻密度低，因而強度不高； （ 2 ） 、在750 1300的溫度范圍內易分解成氧化鋁和二氧化鈦，造成材料內部應力集中，並使材料的熱膨脹率升高。
  12. The questions the researcher concerned are which system will be chosen and how to obtain the good lithium ionic conductor materials, which is the basic departure of the paper. the addition of second phase in composite can change the interface structure and the conduction mechanism, improve the matrix conductivity and other function such as the sintering, crisping and so on, so the research of composites are an interesting field of the ionic conductors. the synthesis of lithium ionic conductor is often by solid state reaction, but this method needs high temperature and leads to the volatility of lithium which not only causes the drift of the compounds but gets the no well - distributed materials

    研究者所關注的問題是選擇新的體系進行研究，以期得到性能更好的鋰離子導體材料，這也正是本論文的基本出發點；復合離子導體中第二相的加入改善了基質的界面結構和導電機制，不僅可以提高基質材料的電導率，還可以在一定程度上改善材料的其它性能，如燒結性能、脆性和機械強度等。因此復合材料的研究是離子導體一個有廣闊前景的發展方向；合成鋰離子導體，特別是成分復雜的體系以傳統的固相合成法為主，但這種方法需要較高的溫度，容易引起鋰的揮發，從而造成產物組成的偏移，而且不易得到顯微結構均勻的材料。
  13. Series ceramic sanitary ware products on the corrosion resistance using non - radioactive zirconium a - glaze, high temperatures over 1, 200 degrees, fired, glass products are completely dense, high strength, wear resistance and corrosion resistance, good bacteria difficult to generation, dual water - saving 3 liters / 6 liters meet international standards

    採用耐酸堿的無放射性雙a鋯釉，在1200多度高溫下燒制，產品完全緻密玻化，強度高，耐磨性和耐酸堿性好，細菌不易生成，雙節水3升/ 6升，符合國際標準。
  14. Ceramic grain filters ard made of refined pottery clays added with certain modifiers, and processed of grinding, mixing, shaping and high temperature sintering. they do not contain any substances that harmful to people or environment. they are hard and rough in surface, porous inside the structure, and have the advantages of high mechanical strength, large specific surface area and porosity. when used in water treatment, they behave a activated surface property, a great amount of pollutant entrapment, less water head loss in the filter bed, lower consumption of back - flush water, stable in chemical and gbiologic property, and long service life, ceramic grain filters is a new and efficient filter material to increase the water yield, upgrade the water quality, and save chemicals and energy

    陶粒濾料是以精製陶土為主要原料，摻加適量改性劑，經粉碎，混練，成型和高溫煅燒而製成的，不含任何對人體和環境有害的物質.其表面堅硬，粗糙，內部疏鬆，多孔，具有機械強度高，比表面積大，孔隙率大的特性.用於水處理中，具有表面性狀好，截污能力強，過濾水頭損失小，反沖洗耗水量低，化學穩定性和生物學穩定性好，使用壽命長的特點.陶粒濾料是一種能增加水產量，提高出水質量，節省藥劑和能耗的新型高效過濾材料
  15. The preparation of metal - supported mullite and zro2 / batio3 ceramic membranes was studied. the influences of ceramic composition, sintering temperature and carbon content on the properties of ceramic materials ( porosity, pore diameter and strength, etc. ) were investigated. alkali corrosion resistance and electrolytic experiment results of these ceramic membranes were compared to those of asbestos and al2o3 porous ceramic membranes

    研究金屬支撐平板陶瓷膜的制備工藝技術，陶瓷膜的組成、燒成溫度、碳含量對材料性能（孔隙率、孔徑、強度等）的影響，比較幾種材料的陶瓷隔膜堿蝕量與電解實驗結果。
  16. The parameters of impregnation are as follows : ph is about 3, the range of temperature is from 20 to 45, and the time is about 2 to 6 hours. after the necessary treatments, zirconia cloths had the optimal strength when the diameters of zirconia fibers were controlled in 4um to 7um, and the sizes of zirconia grains were in 50nm to 100nm. the affec - ting factors were discussed and the liner regression analysis of the cloths was made, from w hich they show that the diameters and grain sizes have the significant influences on zirconia cloths. the obtained zirconia cloths have been accepted for use in nickel - hydrogen batteries by practical use

    研究結果表明：粘膠類纖維布最適合制備氧化鋯纖維布的前軀體；鋯液濃度以飽和溶液為宜；浸漬工藝參數為ph值3左右，溫度20 45 ，時間2 6小時；多餘鋯鹽的去除、浸鋯液后纖維布的整平處理及平燒施應力燒成有利於氧化鋯纖維布的柔軟及平整; 200 600燒成溫度段應緩慢燒成，控制氧化鋯纖維直徑在4 7 m ，氧化鋯晶粒尺寸50 100nm時氧化鋯纖維布的強度最好。
  17. 2. the severe erosion is due to the bad skeleton intensity and isolated w particals, which results from the poor reduce of w surface oxidation. when the arc works, the capillary iv is poor, so cu is splitting greatly

    （ 2 ）嚴重燒損是由於w粉表面的氧化膜在燒結過程中不能很好的還原，致使骨架的燒結強度不高，大部分w顆粒以孤立的狀態存在，毛細作用微弱， cu很容易噴濺，在反復的開斷后， w顆粒剝離造成。
  18. The experiment showed that the temperatures and the fiber proportions influenced great on the compressive strength, bending strength, volume density and the porosity of the composites

    實驗結果表明，燒成溫度和纖維含量對復合材料的耐壓強度、抗折強度、體積密度和氣孔率影響較大。
  19. It was found that there was a close relationship between the adhesion strength of the bg coating and the surface roughness of the titanium alloy and the firing temperature. the chemical state of the elements ti and si at the coating interface varied. the chemical bond and the mechanical occluding make the bg coating form a strong adhesion with the titanium alloy

    通過研究發現， bg塗層與基體的結合強度與基體表面的粗糙度以及燒成溫度密切相關，塗層界面處ti元素和si元素的化學狀態發生了變化， bg與基體強結合的機制為化學鍵和機械嵌合兩種力共同作用。
  20. At the same sintering temperature, when the alumina fiber accounted for 10 %, the porosity of the composites was the lowest, the volume density was the biggest, and the compressive strength and the bending strength were the highest. when the sintering temperature was 1550 c, the compressive strength which could reach 332. 78 mpa, was the biggest ; when the sintering temperature was 1550 c, the bending strength which could reach 44. 04 mpa, was the biggest

    在同一燒成溫度下，氧化鋁纖維含量為10時，復合材料的氣孔率最低，體積密度最大，耐壓強度和抗折強度最高；燒成溫度在1550時，復合材料的耐壓強度最高，達到332 . 78mpa ，在1500時，復合材料的抗折強度最高，達到44 . 04mpa 。
分享友人
分享到 Line

分享到臉書