燒蝕試驗 的英文怎麼說

中文拼音 [shāoshíshìyàn]
燒蝕試驗 英文
ablation test
  • 燒 : Ⅰ動詞1 （使東西著火） burn 2 （加熱或接觸某些化學藥品、放射性物質等使物體起變化） cook; bake; hea...
  • 蝕 : Ⅰ動詞1. （損失; 虧耗） lose 2. （腐蝕） erode; corrode Ⅱ名詞（天體現象） eclipse
  • 試 : 名詞（古代占卜用的器具） astrolabe
  • 驗 : 動詞1. （察看; 查考） examine; check; test 2. （產生預期的效果） prove effective; produce the expected result
  • 試驗 : trial; experiment; test
  1. Improvement on ablation and erode of mechanized gun evacuator

    自行火炮抽氣裝置防燒蝕腐蝕的改進試驗
  2. Test method for oxyacetylene ablation testing of thermal insulation materials

    熱絕緣材料的氧乙炔燒蝕試驗方法
  3. Standard test method for determining the corrosive effect of combustion products using the cone corrosimeter

    用錐形腐蝕計測定燃燒製品腐蝕效應的標準試驗方法
  4. 10. 02 fire test response standard for determining the corrosive effective of combustion products using the cone corrosimeter

    用錐型腐蝕計測定燃燒產品腐蝕效應的火焰試驗響應標準
  5. Standard test method for obtaining char density profile of ablative materials by machining and weighing

    用機械加工法和稱重法獲得燒蝕材料炭密度縱面圖的試驗方法
  6. Fire hazard testing - assessment of potential corrosion damage by fire effluent - general guidance

    著火危險試驗.燃燒排出物引起的潛在腐蝕損壞的評估.通用指南
  7. Real - time ablation measurement test of insulation based on rtr technique

    技術的絕熱層燒蝕實時測量試驗
  8. The conclusion obtained from experimental result showed that particle concentration is an important factor on inhibitor ablation

    試驗結果表明：粒子聚集濃度是絕熱層燒蝕的重要影響因素。
  9. Now, it has run successfully on the measurement system developed for cpla weapon trial center

    現已成功應用於總參某兵器試驗中心的火炮藥筒燒蝕面積測量系統中。
  10. Based on a cone - shaped compound heatshield, a series of research work has been done from the investigation of theoretical analyses of ablative and insulating principles and technical experiments. 1 based on the exploration of improving material performances, a feasible scheme of adding insulating functional layer is proposed ; 2 a simplified calculation method is proposed via establishing fea ( fmite element analysis ) and instantaneous heat transmission is calculated with the mentioned method ; 3 a practical engineering scheme is proposed through a series of experiments ; 4 the interface problems of the function layer are solved through co - curing method and successful samples are manufactured ; 5 in order to estimate properties, the heatshield was anatomized engineering applied possibility is explored on the analyses of performance evaluation by testing mechanical properties, coefficient of heat conductivity and doing dynamic ablative experiments, also, the comparison with that of the required materials is done

    本文以一錐形復合防熱套為研究對象，從燒蝕、隔熱機理的理論分析和工藝試驗兩方面，進行了一下研究工作： 1 、通過對提高材料及製品通過對提高材料及製品隔熱性能的多種途徑進行探討，提出了採用添加隔熱功能層，研究復合型大面積防熱套是理論有效、工藝可行的方案； 2 、通過建立有限元分析模型，對防熱套的燒蝕隔熱行為進行了理論分析，提出了簡化的隔熱計算方法，並用該方法對復合型防熱套的瞬態傳熱模型進行了分析計算； 3 、通過復合型防熱套的工藝探索試驗，提出了一種工程應用上切實可行的工藝方案。
  11. By analyzing the characteristic of the flow field in overloading srm and comparing several existing experiment techniques, a convergence - fold tube facility was developed. the flow field in chamber of srm with high acceleration was simulated. some inhibitor ablation experiments were carried out in this test facility

    通過分析過載條件下流場的特點，提出並比較了現有過載地面模擬試驗技術的優缺點，最終確定了收斂?折管的模擬試驗方法，模擬了高過載條件下發動機燃燒室內的高濃度粒子流，利用該方法開展了高過載模擬沖刷條件下的絕熱層燒蝕特性研究及絕熱層抗沖刷能力的篩選試驗。
  12. The scar on the surface of steel part of the projectile shows that different reaction violence have happened, though the impact velocities of projectile are almost the same in these tests

    從數發試驗回收的鋼托的表面燒蝕痕跡，可判斷相近撞擊速度下反應的烈度不盡相同。
  13. The results of static firing test shows that the thermal erosion properties, mechanical properties, tand thermal shock resistance of the c / sic composites can meet a demand for thermal - structure application in the area of aerospace such as liquid rocket thruster

    試驗發動機地面熱試車結果表明，該c / sic復合材料的力學性能、燒蝕性能和熱震性能優良，可滿足宇航工程中諸如液體火箭發動機推力室等對熱結構材料的使用性能要求。
  14. Finally, the numerical technique was used to investigate influence that different parameters on ablation rate. the relationship between oxygen percentage, pressure, depth of charred layer and ablation rate were obtained

    最後計算了不同參數對材料燒蝕率的影響，得到了燒蝕率隨富氧含量、試驗段壓強以及炭化層厚度變化的趨勢。
  15. Fire hazard testing - part 5 - 3 : corrosion damage effects of fire effluent ; leakage - current and metal - loss test method

    著火危險試驗.第5 - 3部分:燃燒廢氣的腐蝕破壞效應.漏泄電流和金屬損失試驗方法
  16. Test method for heat of ablation

    燒蝕的熱試驗方法
  17. In order to explore the influence of particle diameter on flow field and ablation, particle collection experiments under simulated acceleration conditions were conducted and diameter distribution was obtained

    為分析粒徑對流動計算、燒蝕的影響，開展了模擬過載條件下的粒子收集試驗，獲得了在聚集狀態下的粒徑分佈。
  18. An experiment system simulated afterburner oxygen - riched condition was established. the system was composed of ablation test motor, gas supply pipeline and measurement and control system

    該系統由富氧燒蝕發動機、氣路系統和測控系統組成，能夠模擬固沖發動機二次燃燒室富氧環境，進行絕熱層材料燒蝕試驗。
  19. The cable must pass gb 12666. 2 test " zr " type flameproof pvc insulation and sheath power cable passed the gb 12666. 5 test and has anticorrosive feature

    「 zr 」型阻燃聚氯乙烯護套電力電纜能經受gb12666 . 5的耐燃燒試驗，聚乙烯護套電纜具有優良的耐溶劑腐蝕性。
  20. By observing the macrocosmic and microcosmic state of the test specimens, the ablation pattern of inhibitor was put forward and ablation mechanism was analyzed. the critical average particle diameter that influenced inhibitor ablation was obtained. the time - dependent ablation expression associated particle concentration and angle was achieved through analyzing their variation alone with the change of specimen figure

    （ 4 ）通過對試驗后絕熱材料試件的表觀和微觀狀態分析，提出了過載條件下絕熱層的燒蝕模式，並分析了其燒蝕機理，獲得了試驗條件下影響絕熱層燒蝕的平均顆粒直徑。
分享友人
分享到 Line

分享到臉書