直度 的英文怎麼說
中文拼音 [zhídù]
直度
英文
straightness-
Armhole curve straight
夾圈彎度直度Lack of orthogonality between a suspension(or centering)axis and the spin axis will then result in a drift-producing torque exerted on the gimbal.
懸掛軸和自轉軸間的不垂直度將引起產生漂移作用在框架上的力矩。Test method for the squareness and flatness of mineral wool board
礦物棉板垂直度及平整度試驗方法Measure the straightness, parallelism and squareness
測量直線度、平行度和垂直度。Abstract : checking and measuring the vert icality is very important in the vertical control of high - rise building const ruction
文摘:垂直度檢測在高層建築施工的豎向控制中十分重要。Test method for the squareness and
礦物棉板垂直度及平整度試驗方法Door leaves - measurement of dimensions and of defects of squareness
門扇.尺寸和不垂直度的測量Wood - based panels - determination of squareness and straightness of boards
人造板板的垂直度和邊緣直度的測定Roundness inspection machine tokyo seimitsu inspection roundness, straightness squareness for control the vibrancy and precision of bearings
測量圓度直線度圓柱度垂直度,控製成品的振動和精度It is apparent that the error of piecing and locating the corrugated pipe and the error of level and upright and leaking in the part lead to increase of friction loss
究其原因,與施工工藝密切相關,主要是波紋管逐節段拼接定位、平直度誤差及局部漏漿等所致。With the face grinding attachment, perpendicularity of the end face to the bore after grinding can guaranteed
帶有端磨裝置,保證工件端面與孔的垂直度。Now developing successfully “ gearbox synthetic inspection instrumentation ” can measure simultaneously the first and second bearing bore diameter and verticality parameters of gearbox case. information acquisition and data processing is controlled by computer. the instrumentation improves the inspection efficiency and meets the demand of mass - produced
本課題研製的變速箱殼體綜合檢測儀可實現在線檢測變速箱殼體一軸軸承孔直徑、二軸軸承孔直徑、一軸端面垂直度、二軸端面垂直度等幾何參數。4. install the other parts of frames ; adjust the goodness of fit from inner to outer, pay attention to observe the vertical and horizontal degrees of the main board
4安裝門框其餘各部且依由內至外的原則調整吻合度,注意觀察各主板的水平垂直度The measuring tool series includes 2 kinds, 10 models applied for the correctness of straightness, level and vertical position installed of guide rail on all kinds machines tools and equipments, checking tiny inclining angle
量儀產品水平儀系列,主要有兩個大類,十個品種,用於檢驗各種機床及設備導軌的平直度,安裝的水平位置和垂直位置的正確性,並可檢驗微小傾角。Analysis of non - verticality of the center line of cylinder with the center line of bearing of crank shaft
氣缸中心線與曲軸軸承中心線垂直度的分析Based on the construction of guangzhou metro line 3 welding process and quality control, this paper introduces the mobile contact welding, analyzes some key points during the process of welding, such as welding of rails in curved sections, environmental protection, the measurement of straightness on the welding junctions located in curved sections, the maintenances of equipment etc., holds that more attention shall be given to these points
摘要介紹了移動式接觸焊在廣州地鐵3號線中的施工工藝及施工過程;分析施工過程中應該注意的曲線鋼軌焊接、環境保護、曲線鋼軌焊接接頭平直度的測量、設備維修保養等技術要點。Experiment study on tension control of strip flatness
帶材平直度的張力控制實驗研究Wood wool slabs. measurements of dimensions and edge squereness
木絲板.尺寸與邊的垂直度的測定Wood - based panels ; determination of dimensions of boards ; part 2 : determination of squareness and edge straightness ; german version en 324 - 2 : 1993
木質板料.板料尺寸測定.垂直度和棱邊平直性測定Test method for determining floor flatness and levelness using the f - number system
用f -值系統測定地板平直度和水平度的試驗方法分享友人