直接嚙合 的英文怎麼說

中文拼音 [zhíjiēniègě]
直接嚙合 英文
positive gearing
  • 直 : Ⅰ形容詞1 （成直線的; 硬挺的） straight; stiff 2 （跟地面垂直的; 從上到下的; 從前到后的） erect; v...
  • 接 : Ⅰ動詞1 （靠近;接觸） come into contact with; come close to 2 （連接; 使連接） connect; join; put ...
  • 嚙 : 動詞[書面語]1. （鼠、兔等用牙啃或咬） gnaw （at） 2. （侵蝕） erode
  • 合 : 合量詞（容量單位） ge, a unit of dry measure for grain （=1 decilitre）
  • 直接 : direct; immediate
  1. Size and obliquity of tooth directly influence clutch whether normal operating. it is a key part for ensuring normal operating of aira too. this article fully deduces their compute formula

    該齒形的大小、傾角直接影響離合器是否能正確地嚙合和分離，也是保證機構進行正確工作的關鍵部分，本文詳盡推導了它們的計算公式。
  2. On the condition of “ many - head ” and “ small drive ratio ” ， the plane double enveloping hourglass worm can not settle the problem of undercutting and sharpening simultaneously. it has devoted to a new type hourglass worm _ sphere double enveloping hourglass worm. the coordinate system is established according to the frock. the meshing equation and the tooth equation of worm and gear have been developed and the distribution of contact line on gear tooth is analyzed. to evaluate the meshing quality ， four meshing quality indexes and five original parameters are put forward. through mass programming computing ， the relations between meshing quality and original parameters are derived and depicted by graphs

    考慮到平面二次包絡環面蝸桿傳動在多頭小傳動比條件下根切與齒頂變尖的矛盾很難同時解決且嚙合性能較差，介紹了一種新型環面蝸桿傳動? ?球面二次包絡環面蝸桿傳動.在研究過程中，根據工裝建立了坐標系，根據一二包過程的運動關系推得了嚙合方程和蝸桿與蝸輪的齒面方程，分析了蝸輪齒面上的接觸線分佈.為了評價嚙合性能，提出了4項性能指標和5項原始參數，通過大量編程計算得到了嚙合性能指標與原始參數之間的關系，並以圖表直觀的表示
  3. This essay takes the method of listing equations of gears " surface directly and installing them in appropriate coordinate system to establish the mathematic model for analyzing engagement of spiral helical gear. programs use this mathematic model to make numerical computation as well as to output the contact domains diagram and the relative velocity diagram on this foundation

    本文採用直接列寫齒面方程、在適當的坐標系中安裝的方法，建立了螺旋齒輪嚙合分析的數學模型，編製程序利用該數學模型進行數值計算，並在此基礎上輸出接觸區圖和相對速度圖。
  4. Through systemic analyzing on spiral helical gear transmission with different basic parameters, the essay found out rules of how can such basic parameters influence spiral helical gear engagement characteristics. so it brings forward the auxiliary assembling mode of adopting one straight gear and one helical gear on condition of little axial angle as well as treasures to ameliorate ill engagement performance on condition of large axial angle, another two jobs of the essay are to clarify the wrong concept that spiral helical gear can only transmit movement but not impetus and to provide a brief and practical method of analyzing contact for gear pairs whose surface equations can be written out directly

    通過對不同基本參數的螺旋齒輪傳動進行系統研究，找出了螺旋齒輪基本參數對其嚙合特性的影響規律，提出小軸交角條件下可採用一直齒輪、一斜齒輪的齒輪副組合方式，給出了大軸交角條件下嚙合性能不良的改進措施。澄清了螺旋齒輪只能傳遞運動不能傳遞動力的誤區，為能夠直接寫出齒面方程的齒輪副進行齒面接觸分析提供了一種簡便、實用的新方法。
  5. The camshaft and crankshaft gears can be connected directly, or meshed. this type of operating linkage commonly is used on older six - cylinder, inline engines

    凸輪軸和曲軸齒輪可能被直接連結，或者相嚙合。這類操作聯動通常被用在更老的六氣缸，直列發動機上。
  6. Gearboxes require closer tolerances, since instead of using a large loose chain to transfer force and adjust for misalignments, the gears mesh directly with each other

    變速箱需要更精密的公差配合，因為不是使用一條又大又松的鏈條來傳送力量，也不用調整錯位，輪之間直接和對方嚙合。
  7. Firstly, the paper introduces the development and application of computer graphics & image technique, discusses the principle and method of cg and digital image processing, such as matrix of the graphic transformation, homogeneous reference frame, sampling and quantization of the image, file format of the image, template operation, etc. secondly the paper introduces the purpose and method of image enhancement processing, explains the each occasion of those methods such as threshold transformation, smoothing processing, sharpening processing, analyzes and contrasts the processing results of object image. thirdly, the paper introduces the method of mathematics morphologic, edge detection and thinning processing, attains character description of image and character dots of the contour. fourthly, the paper processes the coordinate transformation to character dots and basic splines fitting, imports correlative condition to devise meshing line and meshing track

    本文首先介紹了計算機圖形圖像技術的發展與應用情況，對計算機圖形學和數字圖像處理的一些基本理論和方法如圖形變換矩陣、齊次坐標系、圖像采樣和量化、圖像文件格式、模板操作等內容進行了討論：然後對圖像增強處理的目的和方法進行了介紹，對諸如閥值變換、平滑處理、銳化處理等方法的應用場合進行了說明，並對實物圖像的處理結果進行了分析與比較；接下來介紹了數學形態學方法、對增強后的圖像進行邊緣檢測的方法和圖像的特徵描述方法，並獲取輪廓的特徵點：隨后對獲取的特徵點進行坐標變換，並進行b樣條曲線擬合，引入相關條件生成齒輪副的嚙合線及嚙合軌跡：最後引入等值線和區域填充表示方法，並以等值線和區域填充的形式對弧齒錐齒輪嚙合模擬的載荷分佈情況進行了直觀的表示。
分享友人
分享到 Line

分享到臉書