相對圓 的英文怎麼說
中文拼音 [xiāngduìyuán]
相對圓
英文
relative circle-
The complex nonlinear pursuit - evasion model of two spacecraft in near - earth coplanar orbit is simplified to linear model, the circular region the radius of which is equal to capture radius is defined as target set, capture is achieved when the evader come into the target set and the game is over ; the boundary of useable part ( bup ) is determined, and the analytical form solution of the linear equations is obtained by backward integration of the state variables from the bup, the linear barrier of the pursuit - evasion model and the optimum thrust of the both sides are thus obtained
本文將近地共面軌道內運動的兩飛行器非線性追逃模型簡化為線性模型，以捕獲半徑的圓域定為目標集，確定目標集邊界上的可用部分，並以此為各狀態變量的起點，對時間進行倒向積分，求得線性方程組的解析解，從而確定了該追逃模型的線性界柵，以及界柵上對策雙方的最優推力，即求得了滿足最優策略時相對運動的軌跡和推力。Buildings that have the appearance of a sphere are called geodesic domes
所有短程線圓頂均與正多面體有相對應的關系。Being lacking of understanding of behaviors of circular working shaft, the paper proposed theory about ring - beam ' s load - distribution calculations and analyzed the structural behavior of circular working shaft ( cws ) by the numbers from the standpoint of properties of structural style and stress incorporated with thoughts of shared load introduced to research of cws. first, regarding cws as structure of series of hypothetic horizontal circular rings and vertical beams, and considering cws ' s formation and development, the paper proposed load - distribution thoughts to solve cws ' s calculations. ring - beam calculation theory was put up and software cbtlmp1. 0 was worked out based on the conditions of external applied load shared by rings and beams, and of deformation conformity
首先，本文提出用分載思想解決圓形工作井結構的計算分析問題，將圓形工作井結構看成是由一系列的假想的水平圓環和豎直梁組成的結構，考慮工作井形成過程及形成階段與項進階段的連續性，根據某一時刻相對于上一時刻外載增量由環與梁分擔、環與梁在交叉處變位增量一致的條件將環計算理論與梁計算理論結合起來，據此建立了環?梁分載計算理論並研製了環?梁分載計算分析軟體cbtlmpv1 . 0 。It is mainly characterized in the triangular - lanceolate leaves which are green but white with dark green reticulation along the midrib and more or less truncate at base ; the flowers are erect on the rachis and half - opened ; the lip is tripartite, glabrous, more or less urceolate in side view ; the hypochile is saccate, ovoid and big while the epichile is relatively tiny, reflexed, undivided and transversely oblong or subreniform
本種之主要特徵為： ?呈三角?披針形， ?面?色，沿中?有白色斑塊， ?基多少呈截形；花直?于花軸，半張；唇瓣呈三段? ，平?無毛，側視時多少呈壺型；基段片囊? ， ?形，巨大，先段片相對微小、反卷， ?再細?而呈橫向橢圓形。On the ground of educative theory, this paper exposits connotation and characteristic of project - based learning and why we should also enforce project - based learning in high school. as far as substance of project - based learning and objective circumstance what it should have are concerned, it points out the practical ability. at last, based on that university physics education has relatively longer cycle, it proposes stage pattern for enforce project - based learning and give two concrete cases, which discuss capacitance of confocal oval - shaped stylar capacitor and potential distribution of charged conductor of surface being uniparted hyperboloid
本文在具體的教育理論指導下，闡述了研究性學習的內涵及特點；在大學物理中實施研究性學習的意義；以及就研究性學習的實質和所需具備的客觀條件而言，論述了研究性學習在高校中實施的可行性；並根據大學物理教育具有周期性相對較長和專業循序漸進的特點，提出了研究性學習的階段性模式，並給出了具體的實例，利用保角變換法討論了共焦橢圓柱形電容器電容及單葉雙曲面帶電導體的電位分佈。The mendable canny operator based on the linear interpolation is used to pick up the edge of the pointer, the pointers ’ instructive direction is gotten via the circumference chord length detection method proposed by the article, then according to the central angle of pointer relative to the benchmark and conjunctive relation, the right reading is received the database information management system realizes the consumers ’ water fee management
利用基於線性插值的canny運算元提取邊緣，通過本課題提出的圓周弦長灰度檢測法得到指針的指示方向，進而依據指針相對于基準的圓心角和關聯關系正確讀數。數據庫信息管理系統實現對用戶用水信息的管理，主要功能分三大模塊:一The manufacture system of filament winding ( fw ) and fiber placement ( fp ) is the one of advanced equipment for frp products. it can be used to produce the products of the positive curvature gyration bodies, such as container cylinder, oil tank, tube, orb, cone, assembled body and so on. furthermore, it is more suited to machining some products of the complex bodies such as the surfaces of the negative curvature gyration bodies, the shell components which have slots and reinforced tendons
纖維纏繞/鋪放聯合製造系統是纖維增強塑料（ frp ）製品生產的先進製造裝備之一，可用於製造如圓筒容器、儲罐、管、球、錐形體或組合形體等正曲率回轉體的製品，更適用於製造含有負曲率的回轉體表面、具有深槽、加強筋的殼體構件等外形相對復雜的纖維增強塑料製品。In general, the content which is studied in this paper can be briefly summarized as follows : 1 the conic shape of nutrition plug which suit the growing condition of the corn seedling is made certain through contrast study on the root grow character between the corn and vegetable seedling ; then the plug size which bulk is smaller and meets the growing condition of com seedling through cultivating the corn seedling
全文內容概括起來主要有以下幾點： 1通過對玉米秧苗根系生長特性與蔬菜根系生長特性的對比性試驗研究，確定了適合玉米秧苗生長的圓臺形缽體；進一步通過玉米育苗試驗，確定了能夠滿足玉米育苗生長需要的、體積相對比較小的缽體尺寸。Then, the chaser ' s two orbit roots are selected as variable and visualizing the simulation by contour plot. this part of research draws the conclusion the same as the first part when the target ' s orbit is circular orbit, while the selected two variable can be wildly changed if the target ' s orbit is elliptical orbit. next, wait time before orbit maneuver is simulated
其次，利用可視化的等值線圖研究了追蹤器軌道兩個參數為變量的情況下大范圍軌道機動問題，分析表明對圓軌道目標器交會機動時，追蹤器軌道根數不宜與目標器軌道根數相差過大，而對橢圓軌道目標器交會機動時，追蹤器軌道根數可選范圍較大，機動策略和方法富於彈性。On the other side, based on research on noncircular surface grinding features, this deissertation designs the data structure of simulation driver, then, applies interpolation theory to design the grinding motion simulation module and researches all sorts of cases on constructing the solid swept of grinding wheels in the process of noncircular surfaces grinding, finally, designs nc codes verification simulation module by using design model - based verification technique
在實體模擬技術方面，詳細研究了非圓曲面磨削加工的特徵並設計了對應的模擬驅動數據結構;應用插補原理設計了體現加工速度的運動過程模擬模塊;詳細研究了非圓曲面磨削加工中砂輪的相對和絕對運動掃掠實體的構造，並採用基於精確實體設計模型的驗證方法構建了數控代碼的模擬驗證模塊。Considering different soil spring models for vertical fault movement and horizontal fault movement, two damage cases of pe pipeline in ji - ji earthquake have also been simulated. the large deformation of a buried pipeline under fault movement is investigated in the 4th chapter. to examine the inelastic behavior of buried pipelines, the parametric studies on pipe material property, diameter ( d ), diameter - to - thickness ratio ( d / t ), crossing angle ( ), as well as soil stiffness, have been conducted using a shell - spring fem method
對於0 p三90 」的情況，當斷層位移相對管徑還不是很大時（管子內的彎曲應變與軸向拉伸應變相差不大的情況） ，斷層附近管子變形形式與梁相似；當斷層位移相對管徑很大時（管子以軸向拉伸應變為主的情況） ，斷層附近的管子軸線變形為一圓弧，管子表現得像一條沒有彎曲剛度的索。So the plate - like drawing correcting process can be divided into two stages : absolute errors checking and comparative errors checking absolute errors checking include four modules which were line - weight checking, hatch checking. dimension checking and overlapped line checking comparative errors checking module include drawing compartmentalization, view recognizing, data getting and data compare in this correction system, line - scanning and circle - scanning algorithm, direct graphics element compare algorithm and character compare are used, which simplify the process and reduce difficulties
相對錯誤檢查包括區域劃分、視圖識別、數據提取、數據提取等過程。相對錯誤的判斷依據是答案圖。本批改系統採用直線和圓弧掃描演算法，並且結合圖形元素直接比較法和特徵比較法，既簡化了處理過程，又降低了處理難度，比較圓滿地完成了開題報告確立的任務。This small artillery ' s age can ' t be dated easily, maybe in ming qing dynasty. as for carving it ' s an old craftwork, but the rare thing is its fine technics. carving on surface is comparatively easy, but on cylinder it ' s much harder, while on prism it ' s most difficult thing i can master. look, this dragon is fresh and full of energy, and must be made by an uncommon man. enjoying it from this point of view can descry the highest art culture connotation which the ancients wanted to express and show
此一小火炮的年代不好定錘，明清物吧，至於雕刻嗎，開門的老工藝，但難得的是工藝精湛，在平面上雕刻相對容易，在圓柱體上就難的多，而在稜柱體上雕刻以及浮雕工藝是最難掌握，你看，這條龍活力四射，昂揚大氣，決非等閑之輩所能造詣，從此一角度和層次去欣賞，便挖掘透視到了古人所欲表達和展示的更高的藝術文化內涵。In the two - body case, the approximate equations of relative motion on elliptic orbits are derived
在二體假設下，推導了橢圓軌道上相對運動方程的近似形式。According to the differential geometry theory, the principle curvatures and principle relative curvature of the spur gear and the fg in line contact and point contact, the tooth surface relative speed and the tooth contact interface are analyzed, whose distributing on the tooth surface are visualized by computer
在齒面的幾何特性研究中，利用微分幾何的原理分析了圓柱齒輪和面齒輪的齒面曲率、線接觸和點接觸面齒輪傳動的主誘導法曲率以及嚙合過程中齒面的相對速度和接觸區域計算問題，並獲得有益的結論。Tooth surface equations and contact line equations of the involute worm gearing are established according to its machining methodology. meshing characteristics in rigidity condition are studied. these characters include the inductive normal curvature along the contact line on the worm surface, the first and the second limit lines during the engage of the worm gear, and the influence of the intersect angle between the contact line the relative velocity of the worm and the gear on transmission performance
根據漸開線圓柱蝸桿傳動的創成方法，建立了漸開線圓柱蝸桿和蝸輪的接觸線方程式、齒面方程式，分析了漸開線圓柱蝸桿傳動的剛性嚙合特性，如蝸桿與蝸輪嚙合時的誘導法曲率、一類界限曲線、二類界限曲線和蝸桿與蝸輪間相對速度方向和接觸線方向的夾角對傳動性能的影響； 2The interaction between the eddy currents and the field therefore will brake the action on the disk.
於是，渦流與磁場之間的相互作用對圓盤產生一種制動作用。In the test of transmission coefficient property, semi - circle type, rectangle type, trapezoid type and concave type dyke are studied. research study is on the effect of relative water depth over the dyke to the transmission coefficient of the four different types dyke, and the comparison is done. finally, the experimental formula is given to the transmission coefficient, which are compared with the present formulae
在潛堤透射特性的研究中，選取半圓型、矩型、梯型和槽型潛堤作為研究對象，在分析各個影響因素對潛堤透射影響的基礎上，選取最主要的影響因素，即相對堤頂水深作為研究的重點，分析研究了堤頂相對水深對四種結構型式潛堤透射系數的影響，比較分析了四種結構型式潛堤透射特性，在此基礎上，總結了計算潛堤透射系數的經驗公式，並與已存在的計算公式進行了對比，最後對潛堤的促淤效果進行了評估。According to the high precision and rotation stability requirement of negative scan unit of cylinder photography typesetting machine, the three levels of cylindrical gears transmission separately, the two - stage cylindrical gears - worm drive, and the worm drive was chosen through calculating its velocity ratio, the checking transmission precision, carrying on the movement precision analysis to the sweep unit, and computing overall transmission error
摘要針對圓筒型照相排版機底片掃描裝置要求傳動精度高，轉動平穩的特點，分別選擇三級圓柱齒輪傳動，雙級圓柱齒輪蝸桿傳動，蝸桿傳動3種常見的傳動方式，計算其傳動比，驗算傳動精度，對掃描裝置進行運動精度分析，計算總體傳動誤差。The activity area of sediment and solution in gooey is distributary river, which has gigantic water power, good degree of sorting and roundness, gruff grain. lower mud and mica content
分流河道的主體部位水動力較強，分選性和磨圓度較好，粒度粗，雲母礦物和泥質含量較低，是膠結物沉澱和溶解的活躍區，因而也是物性相對較好的地方。分享友人