相間連桿 的英文怎麼說

中文拼音 [xiāngjiānliángǎn]
相間連桿 英文
interphase connecting rod
  • 相 : 相Ⅰ名詞1 （相貌; 外貌） looks; appearance 2 （坐、立等的姿態） bearing; posture 3 [物理學] （相位...
  • 間 : 間Ⅰ名詞1 （中間） between; among 2 （一定的空間或時間里） with a definite time or space 3 （一間...
  • 連 : Ⅰ動詞1 （連接） link; join; connect 2 （連累） involve （in trouble）; implicate 3 [方言] （縫） ...
  • 桿 : 桿名詞（桿子） pole; staff
  • 相間 : alternate with
  • 連桿 : [機械工程] link; connecting rod; perch; go between; column; connecting bar; crank guide; link lev...
  1. The main popular theoretical method adopted to study end - plate connection is finite element technique under monotonic loading at present. this paper applies nonlinear ( material, geometry and contact ) finite element method to analyze the behaviors of connections under cyclic load at fist time. contact elements are set between end plate and column flange, screw cap and neighborhood plane, bolt bar and hole

    對于端板連接的理論分析，目前國內外的研究主要局限在單向加載有限元分析范疇，本文首次採用三維非線性（包括材料、幾何與狀態非線性）有限元對端板連接進行了循環加載分析，端板與柱翼緣間、螺栓頭（帽）與相鄰板件間、螺栓桿與孔壁間都設置了反映邊界狀態的接觸單元。
  2. The trucks were themselves pulled off the rails, apparently by the brake rods connecting them to the car body.

    車輪也從軌道上逸脫，這顯然是由於車輛與車輛之間有制動桿相連所致。
  3. Kurstaki strain hd73, were inserted into two copy sets of res sites. the res sites have same direction. when - the recombinant plasmid was introduced into crystal negative b. thuringiensis host bmb171, antibiotic resistance genes and other non - 5, thuringiensis dna can be selectively eliminated after the selection by antibiotic resistance marker

    將crylac10基因或壯觀黴素基因和蘇雲金芽胞桿菌的質粒復制起始區oril030連接在一起，置於兩個同向的解離區之間，再將基因操作中所必需的大腸桿菌質粒復制起始區和抗生素標記基因等與之相連構成解離載體。
  4. With different clearance value, displacement curves and velocity curves of generalized coordinates as well as slider displacement error curves in a motion period are obtained. these curves are discussed. results show that if manufacturing cost is kept invariableness, in order to improve precision of mould - cuting, fitting precision of joint connecting the crank and coupler has priority to be considered to increase

    採用四階rong - kuta法求解連續接觸模型的動力學方程，得到了一個運動周期內運動副間隙取不同值時，各廣義坐標的位移、速度曲線和滑塊位移誤差曲線，並通過曲線分析，得出了要提高模切機主切機構精度，在相同加工成本條件下，應優先考慮提高曲柄與連桿鉸接處的配合精度的結論。
  5. The results show that compared with the intermittent polymerization, the semi - continuous polymerization can greatly improve the reaction rate, and polymer with high relative molecular weight can be easily obtained

    研究表明：與間歇式聚合相比，採用雙螺桿擠出機進行半連續化聚合可以大大加快反應完成的速度，同時還容易制得相對分子質量較高的聚合物。
  6. A new approach of approximate dwell function synthesis for planar six - bar mechanism is presented in the dissertation, which transforms the synthesis of planar six - bar mechanism to the synthesis of two - bar linkage, reduces the variables to four, by selecting all dimensions of the four - bar mechanism in advance. then, based on constraint curves of characteristic points of mechanisms, the characteristic points on the float link can be certained. as a result, unified model of dwell function synthesis of planar six - bar mechanism is set up

    本文提出了一種實現平面六桿機構間歇函數綜合的簡化優化方法，將多維優化轉化為四維優化；從工程實際出發，運用連桿機構運動幾何學、數學規劃和計算機數值計算和圖形顯示技術等學科的理論成果，對平面六桿機構間歇函數綜合進行了深入系統的研究，建立了平面六桿機構間歇函數綜合的理論和方法，並給出了相應的算例。
分享友人
分享到 Line

分享到臉書