瞬動觸點 的英文怎麼說

中文拼音 [shùndòngchùdiǎn]
瞬動觸點 英文
snap action contact
  • 瞬 : Ⅰ名詞（眼珠一動; 一眨眼） wink; twinkling Ⅱ動詞（眨眼） wink
  • 觸 : Ⅰ動詞1 （接觸） touch; contact 2 （碰; 撞） strike; hit 3 （觸動） touch 4 （感動） move sb ; sti...
  • 點 : Ⅰ名詞1 （液體的小滴） drop （of liquid） 2 （細小的痕跡） spot; dot; speck 3 （漢字的筆畫「、」）...
  1. A data acquisition system with the following features is realized : ? transmission rate up to 100kbyte / s over usb ; ? system ' s dynamic range as high as 120 db ; ? multi - kind of trigger mode control ; ? sampling rate as high as 100 ksps ; ? 12 - bit a / d conversion accuracy ; ? 32k bytes on - board data memory ; ? the system, which was made up of large - scale electronic chips, is small, light and portable, and suitable for field use

    本設計最終實現了一個瞬態信號數據採集系統，它具有以下特點： ?採用usb介面進行高速數據傳輸，傳輸速度達100kbyte / s ； ?採用浮點a / d轉換技術，動態范圍達120db ； ?多種采樣觸發控制方式； ?最高采樣率100ksps ； ? 12位采樣精度： ? 32kb數據緩存； ?使用新型大規模電子器件，系統結構緊湊，重量輕，適合野外作業。
  2. Equations of mesh, shorting contact line, undercutting limit line, meshing limit lines and the existence conditions, angle between the direction of relative speed and the direction of contact line, induced normal curvature about every point on the contact line are established. moreover, the paper also theoretically analyzed the error of the grinded gear surface. on the basis of the theory, the computer program is worked out to automatically produce the contact line and the boundary curves of mesh. analysis of meshing circs under different parameters can be done so that we can gain the best process condition

    首先對漸開面二次包絡理論進行了深入的探討，推導出了兩次嚙合的嚙合方程式、瞬時接觸線方程式、根切界限線方程式、嚙合界限線的方程式及其存在條件，相對運動速度方向與接觸線方向的夾角及接觸線上各點的誘導法曲率；此外，還對磨齒后工件的齒面誤差進行了理論分析；並在理論基礎上編制了相應的計算機程序，自動生成接觸線族及嚙合界限線，對不同參數條件下的嚙合情況進行分析，可以使工藝條件達到最佳狀態；最後研究了磨齒裝置，設計了磨齒機的傳動系統。
  3. Magnetoelectric sensor is a kind of non - contact sensor and has some useful characteristics, such as non - contact, high response frequency, low power waste, high reliability, long life - span and etc

    磁電傳感器是一種非接觸式傳感器，它具有無觸點、無開關瞬態抖動、響應頻率高、低功耗、高可靠性和長壽命等特點。
  4. The contact deformation at transient engaging point is derived from deeply analyzing geometric property and kinematics relationship between the two action flanks by use of engagement principle, differential geometry, elastic and plastic mechanics, etc

    運用嚙合原理、微分幾何和彈塑性力學等基礎知識，對齒面間的幾何性質和運動關系進行深入細致的分析研究，計算各瞬態嚙合點的接觸變形。
  5. 4 、 on the basis of analyse of a quasi - static meshing simulation in a meshing period, a dynamic meshing simulation in the case of definite torque and rotary speed are carried out in a meshing period. the numerical results which indicating the variety of the contact status, the contact stress, the bending stress in the location of teeth root and the torque and rotary speed of gear pair vs the different meshing position are presented

    4 、在對螺旋錐齒輪準靜態嚙合進行模擬分析的基礎上，進行了螺旋錐齒輪動態瞬態嚙合模擬分析，重點分析帶載啟動時出現的沖擊現象，得出了齒輪的接觸狀態、接觸應力、齒根彎曲應力及主從動齒輪的扭矩、轉速和加速度隨嚙合位置變化的規律。
分享友人
分享到 Line

分享到臉書