瞬時接觸 的英文怎麼說

中文拼音 [shùnshíjiēchù]
瞬時接觸 英文
momentary contact
  • 瞬 : Ⅰ名詞（眼珠一動; 一眨眼） wink; twinkling Ⅱ動詞（眨眼） wink
  • 時 : shí］Ⅰ名1 （比較長的一段時間）time; times; days:當時at that time; in those days; 古時 ancient tim...
  • 接 : Ⅰ動詞1 （靠近;接觸） come into contact with; come close to 2 （連接; 使連接） connect; join; put ...
  • 觸 : Ⅰ動詞1 （接觸） touch; contact 2 （碰; 撞） strike; hit 3 （觸動） touch 4 （感動） move sb ; sti...
  • 接觸 : 1. （交往） come into contact with; get in touch with 2. （沖突） engage 3. （挨上; 碰著） contact; touch
  1. Floc point the lowest temperature at which vapors rising a sample will ignite momentarily on application of a flame under specified conditions

    在規定條件下，油品加熱后所逸出的蒸氣與火焰接觸發生瞬間閃火時的最低溫度。
  2. Established the system of coordinates of roll testing, getting the parameters of equation of tooth face by solving the non - linear equations set ; according to the differential geometry and meshing principle, deduce the curvature parameters of tooth face and tooth profile, and get the parameters of instantaneous contact ellipse. emulate the contact trace and contact area of the working tooth face, and drawing the instantaneous drive ratio error curve

    建立了克林貝格擺線齒錐齒輪嚙合分析的對滾模型，通過對非線性方程組的迭代求解，得到齒面方程的各個參數;由微分幾何和切齒嚙合原理推導了齒面上齒廓和齒線方向的曲率參數，得到了瞬時接觸橢圓的參數。根據設計參數和機床調整參數繪制了工作齒面的接觸軌跡和接觸區圖形，並求得了瞬時傳動比的誤差曲線。
  3. Solid model of the involute worm gearing solid model with drive ratio 1 / 50 is built by using ideas - 5. 0, then the elastic contact analysis is proceeded on the basis of contact fem. the dynamic evolution image of the area of the contact zone, the load sharing among instantaneous meshing tooth pairs, the distribution of the contact force, and tooth stress are obtained. 3

    通過漸開線圓柱蝸桿、蝸輪的齒面方程式，利用ideas - 5 . 0軟體建立了傳動比為1 / 50的漸開線圓柱蝸桿傳動的實體幾何模型，在此基礎上應用接觸有限元方法對該傳動進行了彈性接觸分析，包括接觸區的形狀、位置、載荷在瞬時嚙合齒對的分配狀況； 3
  4. Principal conclusions were drawn as the following : the non compatibility of pressure or velocity of the gas on both sides of the contact surface is the cause of the formation of shock wave ; the heating effect of reflective shock wave to driving gas during charging or exhausting process is the internal mechanism of peak oscillating effect, and all the factors that influence the formation and the running of the shock wave will influence the peak oscillating frequency, cooling effect

    主要結論如下：熱分離機內激波形成的原因是射氣瞬間接觸面兩側壓力和速度不相容；峰值振蕩效應的內在機制為反射激波對充氣階段的驅動氣或低溫排氣的加熱，凡是影響激波形成及運動的因素都將對峰值振蕩頻率、冷效應及熱效應產生影響；當充、排氣時間比為0 . 1763時，最佳射流激勵頻率出現在高階峰值振蕩頻率上。
  5. Floc point the lowest temperature at which vapors rising from a sample will ignite momentarily on application of a flame under specified conditions

    閃點在規定條什下，油品加熱后所逸出的蒸氣與火焰接觸發生瞬間閃火時的最低溫度。
  6. Detail specification for non - sensitive pushbutton switch momentary contact

    瞬時接觸式非靈敏按鈕開關的詳細規范
  7. Equations of mesh, shorting contact line, undercutting limit line, meshing limit lines and the existence conditions, angle between the direction of relative speed and the direction of contact line, induced normal curvature about every point on the contact line are established. moreover, the paper also theoretically analyzed the error of the grinded gear surface. on the basis of the theory, the computer program is worked out to automatically produce the contact line and the boundary curves of mesh. analysis of meshing circs under different parameters can be done so that we can gain the best process condition

    首先對漸開面二次包絡理論進行了深入的探討，推導出了兩次嚙合的嚙合方程式、瞬時接觸線方程式、根切界限線方程式、嚙合界限線的方程式及其存在條件，相對運動速度方向與接觸線方向的夾角及接觸線上各點的誘導法曲率；此外，還對磨齒后工件的齒面誤差進行了理論分析；並在理論基礎上編制了相應的計算機程序，自動生成接觸線族及嚙合界限線，對不同參數條件下的嚙合情況進行分析，可以使工藝條件達到最佳狀態；最後研究了磨齒裝置，設計了磨齒機的傳動系統。
  8. This kind of catalyst was very fine, with strong interaction between the support and the active component particle, and high dispersion of such particles on the surface of the support. yield of carbon nanotubes can also be improved greatly by the doping of molybdenum to catalyst

    本文所採用的檸檬酸法瞬時燒爆工藝制備的催化劑，顆粒小，載體與活性組分接觸好，活性組分分散均勻，可望實現單壁納米碳管的大規模製備。
  9. The project studied the direct contact condensation behavior of saturated steam on the subcooled liquid in passive gravity injection system. the experiment parameters were as follows : the initial pressure of prz ranged from 0. 2 0. 6mpa and the initial fluid temperature of core makeup tank ranged from 10 80. condensation phenomenon in cmt was observed

    本課題進行了非能動重力補水系統中飽和蒸汽在過冷液面上直接接觸冷凝的實驗研究，研究了在加裝遮流板時，系統壓力0 . 2 0 . 6mpa ， cmt初始溫度為10 80條件下壓力容器cmt中飽和蒸汽在過冷液面上冷凝的瞬態特性。
  10. In real engineering, the two surfaces in sliding contact are rough. and it is an important theoretical part to calculate the coupled temperature and stress of sliding bodies having rough surfaces

    工程實際中，相互接觸的滑動摩擦表面是粗糙的，對粗糙表面的瞬時溫升和熱機械應力分析有重要的理論意義。
  11. Prediction of instantaneous maximum temperature in friction contact area by spontaneous electric thermo - couple

    用自然熱電偶測量值估計摩擦接觸的最高瞬時溫度
  12. Instantaneous contact pattern

    瞬時接觸斑點
  13. This unit utilizes a unique spray nozzle and a high - speed rotary plate ( centrifugal model ) to granulate fluid ( starchy materials ), and sprays hot air to instantly dry the granules as their surface areas are being increased

    利用特殊噴嘴或者是高速旋轉圓盤（離心式）將漿料球粒化，並再它表面積增大時，施以連續熱風，使其與熱風接觸后瞬間乾燥。
  14. Based on g - w contact model, two rough surfaces in contact were simplified to a smooth one and a rough one which has regular rectangular asperities, and a three - dimensional transient thermal and stress coupled fem model was established using thermal - structure sequential coupling. the course of the sliding with friction was simulated using the nonlinear multiphysics field fem, meanwhile considering thermal - elastic problems of the two bodies, to calculate and analyze the temperature, contact pressure and stress of the sliding contact surfaces with frictional heating

    基於g - w接觸模型，將兩個粗糙表面簡化為一個有規則排列的長方體微凸體的粗糙表面與一光滑表面，利用熱結構順序耦合建立三維瞬態有限元計算模型，考慮兩個物體摩擦接觸的熱彈性問題，採用非線性有限元多物理場來實現，對粗糙表面接觸模型的瞬時摩擦溫度場、壓力場和應力場進行了計算分析。
  15. When the contacts are connected into direct circuit, we can judge whether the contacts are open or not through analyzing the voltage instantaneous values across the two contacts

    當有觸點電器的觸頭接入直流電路中時，可通過觸頭兩端電壓瞬時值來判斷它是打開還是閉合。
  16. As a tool of whole field, unintrusive and instantaneous measurement, piv has been used widely in parameter measurement of liquid and multiphase and has good measurement precision

    作為一種全流場無接觸瞬時測量的工具， piv測量技術已經廣泛地應用於流體及多相流參數的測量，而且具有較高的測量精度。
  17. As a tool for measuring the whole instantaneous flow field without contacting the flow, piv and related image measurement techniques have been extensively applied to automated measurements of multiphase flows, turbulence and thermal flows with reliable accuracy

    作為一種全流場無接觸瞬時測量的工具， piv和相關的圖像測量技術已經廣泛地應用於多相流、紊流和熱流的自動測量，而且具有可靠的精度。
  18. 4 、 on the basis of analyse of a quasi - static meshing simulation in a meshing period, a dynamic meshing simulation in the case of definite torque and rotary speed are carried out in a meshing period. the numerical results which indicating the variety of the contact status, the contact stress, the bending stress in the location of teeth root and the torque and rotary speed of gear pair vs the different meshing position are presented

    4 、在對螺旋錐齒輪準靜態嚙合進行模擬分析的基礎上，進行了螺旋錐齒輪動態瞬態嚙合模擬分析，重點分析帶載啟動時出現的沖擊現象，得出了齒輪的接觸狀態、接觸應力、齒根彎曲應力及主從動齒輪的扭矩、轉速和加速度隨嚙合位置變化的規律。
分享友人
分享到 Line

分享到臉書