短時熱試驗 的英文怎麼說

中文拼音 [duǎnshírèshìyàn]
短時熱試驗 英文
short thermal test
  • 短 : Ⅰ形容詞（空間、時間兩端之間的距離小） short; brief Ⅱ動詞（缺少; 欠） lack; owe Ⅲ名詞1 （缺點） we...
  • 時 : shí］Ⅰ名1 （比較長的一段時間）time; times; days:當時at that time; in those days; 古時 ancient tim...
  • 試 : 名詞（古代占卜用的器具） astrolabe
  • 驗 : 動詞1. （察看; 查考） examine; check; test 2. （產生預期的效果） prove effective; produce the expected result
  • 試驗 : trial; experiment; test
  1. The results indicate that drying thickness, radiant temperature and pressure of drying chamber are the most three significant factors. there ' s hardly any relationship between freezing rate and drying time, the sublimation drying time of slow freezing material is shorter than quick freezing one, but its desorption drying time is relatively longer, so the total drying time is approximately the same. the initial freezing temperature and freezing manner has little influence on vacuum freeze drying process

    試驗表明：凍干厚度、加熱板溫度、系統的真空度是最重要的三個過程參數；凍結速率對總凍干時間沒有影響，慢凍物料的升華乾燥時間要比快凍物料短，但慢凍的解析時間相對較長，兩者的總凍干時間相差很小；初始凍結溫度對凍干過程的影響可以忽略。
  2. The results show time interval of atmospheric forcing gives rise to significant difference in net solar radiation and latent heat in siberia area

    西伯利亞地區的單點試驗表明不同時間間隔的邊界強迫對地表吸收的凈短波輻射和釋放的潛熱影響較大。
  3. The optimum conditions of preparation were as fellows : the concentration of zinc sulfate solution of 1. 8 - 2. omol / l, the concentration of ammonium bicarbonate solution of 1. 4 ~ 1. 6mol / l, the time of ultrasonic radiation of 25 ~ 30min. iv. preparation of active zinc oxide by means of microwave radiation to calcine precursor of basic zinc carbonate firstly, and a mechanism on preparation of ultra - fine active zinc oxide by means of microwave radiation has been investigated emphatically as well as the effects on quality of ultra - fine active zinc oxide have been analyzed and discussed in detail, the time of microwave radiation was 7 ~ 16 min ; comparing microwave radiation calcining with conventional calcining, the calcining time of microwave radiation was one thirty to one twenty, the calcining time shortened hugely, energy consumption saved hugely, the quality of product improved

    首次引入超聲波輻射制備超細活性氧化鋅前驅體堿式碳酸鋅新技術，研究了超聲波輻射制備前驅體堿式碳酸鋅的機理，並分析和討論了影響前驅體質量的各種因素，確定了最佳的前驅體制備條件為：硫酸鋅濃度為1 . 8 2 . 0mol / l ，碳酸氫銨的濃度為1 . 4 1 . 6mol / l ，超聲波輻射25 30min ； 4 、首次採用微波加熱煅燒前驅體堿式碳酸鋅制備超細活性氧化鋅的新技術，研究了微波輻射加熱煅燒前驅體制備超細活性氧化鋅的機理，並分析和討論了影響活性氧化鋅質量的各種因素，確定了最佳的超細活性氧化鋅制備條件為：微波加熱煅燒時間為7 16min ，與傳統煅燒方法相比，煅燒時間僅為傳統的1 30 1 20 ，大大縮短煅燒時間，節省能耗，提高了煅燒產品的質量； 5 、完成了從鋅浮渣中制備超細活性氧化鋅的小試試驗和擴大試驗。
  4. In this paper, the models of building and algorithms of estimating model ’ parameters are researched about the parameter model forecast method. the performance decline of the thermal coat materials are forecasted by the models and algorithms using the a few experiments data gained by the short simulated radiation experiment time

    本文主要是基於參數模型預測方法，對模型的建立和模型參數估計演算法進行研究，目的是通過利用短時間的少量試驗數據進行建模，來預測航天器熱控塗層材料在未來長時間內的性能退化規律。
  5. Associated tightly with the stokes measured in small capacity current breaking and short - circuit breaking test duty t100a ( short arc, middle arc and long arc ), the electric field distributions 3 ms after current zero have been calculated. the cold gas flow field corresponding with small capacity current breaking is calculated. based on the results derived from one - dimensioned gas flow field simulation, the two - dimensioned gas flow fields corresponding with short - circuit breaking test duty t100a ( short arc and middle arc ) are calculated as well

    本文採用與試驗緊密結合的方法，在給定機械行程曲線的基礎上對三峽工程中採用的550kvsf6斷路器在開斷小電容電流、短路開斷方式5短、中、長燃弧電流過零后3ms內滅弧室二維靜電場分佈進行了分析計算；對該斷路器開斷小電容電流時近似的冷態場進行了二維模擬分析計算；在對短路開斷方式5短、中、長燃弧一維氣流場進行分析計算的基礎上進一步採用一維氣流場和二維氣流場相結合的方法，對該斷路器開斷方式5短燃弧和中燃弧對應的二維熱態場進行了分析計算。
  6. Methods of test for footwear and footwear materials - solings - resistance of solings to short - term contact with a hot surface

    鞋靴和鞋靴材料試驗方法.第2部分:鞋底.第11節:鞋底與熱表面短時接觸的耐熱性
  7. Test method for short - time hydraulic failure pressure of fiber - reinforced thermosetting plastic pipe

    纖維增強熱固性塑料管短時水壓失效壓力試驗方法
  8. Fiber - reinforced thermosetting plastic composites pipe - determination of short - time hydraulic failure pressure

    纖維增強熱固性塑料管短時水壓失效壓力試驗方法
分享友人
分享到 Line

分享到臉書