研磨斷面形 的英文怎麼說
中文拼音 [yánmóduànmiànxíng]
研磨斷面形
英文
ground shape- 研 : 研同 「硯」
- 磨 : 磨動詞1 （摩擦） rub; wear 2 （研磨） grind; mull; polish 3 （折磨） grind down; wear down [out]:...
- 斷 : Ⅰ動詞1 （分成段） break; snap 2 （斷絕;隔斷） break off; cut off; stop 3 （戒除） give up; abstai...
- 面 : Ⅰ名詞1 （頭的前部; 臉） face 2 （物體的表面） surface; top 3 （外露的一層或正面） outside; the ri...
- 研磨 : 1. （用工具研成粉末） grind; pestle2. （用磨料摩擦器物使變得光潔） abrade; polish
- 斷面 : section; fracture surface; plane of fracture
-
The research of high performance pavement concrete ( hppc ) is done in two sides. one is mixture design, the other is pavement performance. the mixture design and design flowchart of hppc is given on the base of nc with the consideration of characteristic of both hppc and nc. the grow law, influencing factor and formation mechanism of hppc strength is analisised by perpendicular experiment. in the same, the fatigue equations are set up for hppc and hppc i on the base of fatigue experiment. the fatigue mechanism of hppc is analysised by damage mechanics and fracture mechanics. brittleness, frost resistance and abrasion resistance of hppc is researched with the camparition to nc i. at last, the economic analysis of hppc is done by two kinds of way
結合高性能混凝土與普通路面混凝土的特點，提出了建立在普通路面混凝土基礎上的高性能路面混凝土配合比設計方法，給出了設計流程；通過正交試驗（強度試驗） ，分析了高性能路面混凝土的強度發展規律、影響因素與形成機理；同時，根據疲勞試驗結果採用雙參數weibull分佈模型分別建立了高性能路面混凝土和高性能路面混凝土（沒有摻加硅粉）疲勞方程，應用損傷力學和斷裂力學，分析了高性能路面混凝土的疲勞機理；並採用了對比分析方法，研究了高性能路面混凝土的脆性、抗凍性和耐磨性等。The properties of cn thin films such as their morphology, component, crystal structure and the bonding structure and the relation between those properties and the gas - phase reaction parameters were discussed, showing that the deposition of p - c3n4 thin film is the compete result of various reaction processes in the dynamics balance conditions ; the process of cn films depo sition is diagnosed in situ through the optical emission spectra technique, the effects of experimental parameters on the concentration of the precursors and the gas - phase reactions in the plasma have been obtained ; the main reaction precursors for film deposition identified ; the relation between the characteristics of cn thin films and the reaction process in the plasma is analyzed. the cn thin films deposition under different substrate temperatures in high pressure pe - pld shows that the si atom of the substrate has participated the cn films growth process, based on this the growth mode of cn thin films on the si substrate is proposed. the further experiment of cn thin films deposition on si substrate scratched by diamond as well as covered with fe catalyzer has been attempted, which indicates that changing the dynamics conditions of the surface reaction can alter the growth characteristic of the cn thin films and can enhance obviously the films growth rate
採用pld技術進行了碳氮化合物薄膜沉積，得到了含氮量為21at的cn薄膜；研究了襯底溫度和反應氣體壓強對薄膜結構特性的影響，給出了cn薄膜中n含量較小、 sp ~ 3鍵合結構成分較少和薄膜中僅含有局域cn晶體的原因；引入脈沖輝光放電等離子體增強pld的氣相反應，給出了提高薄膜晶態sp ~ 3鍵合結構成分和薄膜的含n量可行性途徑；應用pe - cvd技術以ch _ 4 + n _ 2為反應氣體並引入輔助氣體h _ 2 ，得到了含n量為56at的晶態cn薄膜；探討了cn薄膜形貌、成分、晶體結構、價鍵狀態等特性及其與氣體壓強和放電電流的關系，證明了- c _ 3n _ 4薄膜沉積為滿足動力學平衡條件的各種反應過程的競爭結果；採用光學發射譜技術對cn薄膜生長過程進行了實時診斷，得到了實驗參量對等離子體中活性粒子相對濃度和氣相反應過程的影響規律，給出了cn薄膜沉積的主要反應前驅物，揭示了cn薄膜特性和等離子體內反應過程之間的聯系；採用高氣壓pe - pld技術研究了不同襯底溫度條件下cn化合物薄膜的結構特性，揭示了si原子對薄膜生長過程的影響，給出了si基表面碳氮薄膜的生長模式；在金剛石研磨和催化劑fe處理的si襯底上進行cn薄膜沉積，證明了通過控制材料表面動力學條件可以改變碳氮薄膜結構特性，並可顯著提高晶態碳氮材料的生長速率。( 3 ) in present paper, pan mill type equipment is developed to make fine or ultra - fine waste rubber powder and polypropylene / waste tire rubber composite powder at ambient temperature
Pp wtr復合材料斷面形貌和dmta研究結果表明，共碾磨能促進膠粉在pp基體中的分散性，提高材料的阻尼因子和抗沖擊強度。
分享友人