碰焊 的英文怎麼說

中文拼音 [pènghàn]
碰焊 英文
butt welding
  • 碰 : 動詞1 （一物體突然接觸另一物體; 撞擊） touch; bump 2 （碰見; 遇到） meet; run into 3 （試探 ） tr...
  • 焊 : 動詞（用熔化的金屬修補金屬器物或使金屬工件連接起來） weld; solder
  1. Assemblies incorporating a wire terminal of neon or fluorescent lamp with series resistor, if required, extended single conductor lead wires can be produced with butt welded, crimped or tin soldered joints

    氖燈電阻熒光燈氖燈與電阻的連接可分為：碰焊打銅扣以及錫焊。
  2. In the transition from lead to lead - free, for the manufacturers of electronic products, there is expected to be a period when lead and lead - free materials will be used within the same mounting process, the mixed solder joint which formed in this situation is very complicated

    摘要在從有鉛向無鉛轉換過程中，電子產品製造商不可避免會碰到同一組裝過程中有鉛和無鉛同時存在的混合情況，這種情況下形成的混合焊點是很復雜的。
  3. Even then, seating and gasket faces or buttweld ends can show fine - line cracks that need more upgrading by rewelding and remachining

    即使在這種情況下，閥座和墊圈面或碰焊端可能會顯示需要通過重焊和機加工的細線裂縫。
  4. Collision - free trajectory planning in 3 - d space for welding robot

    焊接機器人在三維空間的無碰撞軌跡規劃
  5. After installation, the position of galvanization coating destroyed due to welding, cutting and scratch etc. shall be carried out anti - corrosive coating by install on site

    對安裝后的焊接部位，裁切口，碰損擦傷等鋅層遭到損傷的部位，要求現場施工人員進行防腐塗裝。
  6. After installation, the position of galvanization coating destroyed due to welding, cutting and scratch etc. shall be carried out anti - corrosive coating by installer on site

    對安裝后的焊接部位，裁切口，碰損擦傷等鋅層遭到損傷的部位，要求現場施工人員進行防腐塗裝。
  7. Design on a simple butt - welding machine

    一種簡易碰焊機
  8. Spring hinge for welding

    碰焊彈弓鉸
  9. Our company is adapted with iso9001 strictly for quality management, and the followong leading products series have populous in market : high - frequency series, ultrasonic series, contact jointing machine series, and plastic inhaling machine series

    本公司嚴格執行iso9001的優化管理，已在市場上形成了四大主導產品：高周波系列、超聲波系列、碰焊機系列、吸塑機系列。
  10. The optimization problem of parameters, example hourglass coefficient, mesh size, jointing simulation and so on, which affect the result of crash simulation, is solved. the size and number projects of steel panel and square column, which make deceleration curve of sled reach the requirement, are found by simulation

    模擬分析研究成功地解決了影響碰撞模擬結果的「砂漏」系數、網格大小、焊接模擬參數等各種相關參數的優化處理問題，為臺車碰撞試驗中得到符合要求的臺車減速度曲線提供了鋼板或方形梁的最佳尺寸及組合方案。
分享友人
分享到 Line

分享到臉書