穩流電感 的英文怎麼說

中文拼音 [wěnliúdiàngǎn]
穩流電感 英文
stabilizing inductance
  • 穩 : 形容詞1 （穩定; 穩當） steady; stable; firm 2 （穩重） steady; staid; sedate 3 （穩妥） sure; rel...
  • 流 : Ⅰ動1 （液體移動; 流動） flow 2 （移動不定） drift; move; wander 3 （流傳; 傳播） spread 4 （向壞...
  • 電 : Ⅰ名詞1 （有電荷存在和電荷變化的現象） electricity 2 （電報） telegram; cable Ⅱ動詞1 （觸電） give...
  • 感 : Ⅰ動詞1 （覺得） feel; sense 2 （懷有謝意） be grateful; be obliged; appreciate 3 （感動） move; t...
  1. Depend on the comprehensive analysis and study of the structure, principle, and exterior characteristic of the motor, through the methods of system modeling and digital simulation analysis, two kind of control device that work for the low voltage ( lvdc ) and the high voltage ( hvdc ) in avigation are researched respectively. point to the control technique of close - loop speed stabilization at a limited adjustment speed range, we bring out the close - loop speed control method that using the rotor position sensor indirectly measure the speed of the motor

    在全面分析了稀土永磁無刷直流電動機的結構特點、工作原理、運行方式以及外部特性的基礎上，通過系統建模和數字模擬分析，分別針對航空低壓直流（ lvdc ）和高壓直流（ hvdc ）兩種電動機構用永磁無刷電動機，在小范圍轉速連續調節下的閉環穩速控制技術進行了詳細理論研究，提出了利用轉子位置傳感器信號間接測量電機轉速進行電機轉速閉環穩速控制的策略。
  2. The steady state saturation and transient state saturation of the current transformer are theoretically analyzed and simutated under different burder at secondary side

    針對二次側不同的負載，對電流互感器的穩態飽和與暫態飽和做出理論分析和模擬。
  3. Lzct bushing type current transformer is suitable for is suitable for current measurement ， metering and microcomputer protection of distribution equipments in 35kv and 10kv ac power system

    該型電流互感器的環型鐵芯和二次繞組採用優質環氧樹脂真空澆注在可阻燃的塑料殼體內，防潮濕，性能穩定，無需維護。
  4. Eddy - current sensor conversion circuit consist amplification circuit, band - pass filter circuit, demodulation circuit, differentiation phase and data sampling circuit. these circuits are used to convert the test signal of eddy - current sensor to discrete signal tend to process. the microprocessor system that formed of dsp chip is used to data fitting of test system, data displaying and data communicating with personal computer, etc. the interference questions of hardware design and the measure of eliminating interference signal in the subject are introduced in the last of this chapter

    硬體電路的設計主要分三大部分來實現：激勵源電路部分，由分頻電路和頻率合成電路組成，產生頻率穩定的激勵信號以確保檢測任務的正常進行；傳感器變換電路部分，由放大電路、濾波電路、檢波電路、鑒相電路和數據採集電路組成，主要將電渦流傳感器檢測線圈檢測到的信號變換成只含有被測信息的離散信號，易於后續電路處理；由dsp晶元構成的微處理系統，主要完成檢測系統的數據擬合、顯示及與主機通信等功能。
  5. And at this foundation through the dispersed domine analyse the paper makes a great emphasis on the application of computer aided design and simulation, then designs a series of apfc design and simulation software. this paper takes out a set of designation and simulation on base of actual circuit. the reliable result, output voltage and inductance current which are got from this software are the same as the actual value

    本文在對一系列apfc電路設計、模擬分析方法討論比較的基礎上，著重應用離散時域法進行了計算機輔助電路設計和模擬方法的應用探索，以此為基礎設計了pfcexpert功率因數校正電路設計、模擬軟體，針對實際電路給出了整個設計和模擬全過程，通過實驗驗證了該軟體所得到的精確穩態解、瞬態輸出電壓和電感電流，與實際電路輸出基本相同，所建立的電路模型重現了電路的運行過程，反映了電路的實際工作機理。
  6. Transitional feature of the arc and metal droplet in the welding process with steam shielded arc is investigated by means of analysing the waveforms of welding voltage and current under different welding regimes and it is found that there are two types of arc process behavor ? " arc starting - arc blowing out - short - circuiting " and " arc - starting - short - circuiting ". under the condition of constant diameter of welding wire and its feeding speed, the arc process behavor can be changed by adjusting the inductance of welding circuit as well as the voltage of power supply. if arc process behaves as alternative process of " arc starting - arc blowing out - short - circuiting " with minimum time duration of arc blowing out and maximum frequency of short - circuit transition, the welding process will be stable with less spatter and smooth weld bead

    通過分析不同焊接規范下的焊接電壓和電流的波形.研究了水蒸氣保護下電弧及熔滴過渡的特點，發現其電弧過程行為有「燃弧?熄弧?短路」和「燃弧?短路」兩種形式.在焊絲直徑和送絲速度一定的情況下，通過調節焊接迴路中的電感量和電源電壓，可以改變電弧的過程行為形式.若電弧過程呈「燃弧?熄弧?短路」交替進行，並且熄弧時間最短時，短路過渡頻率最高，在這種情況下，飛濺小，焊道成型好，焊接過程穩定
  7. The dual - loop control method adapted to current source is proposed - outer loop is the feedback of averaged load current and inner loop is that of inductor current

    逆變電路採用了適用於穩流輸出的雙環控制方式：外環負載電流平均值反饋，內環電感電流瞬時值反饋。
  8. The purpose is that the current transformer often working in wide range current could always get the output current with less error, what means that the ct is in steady low error grade

    為了使經常工作于寬量程電流的電流互感器始終獲得較小誤差的輸出電流，也就是讓它具有穩定的低誤差等級。
  9. The stator of aceg is connected to the grid and the three symmetrical excitation windings in the rotor are fed by converter. the magnitude and frequency and phase and phase sequence of excitation voltage can be controlled, so the magnitude and position of excitation mmf as well as the speed of rotor can be controlled. therefore, acegs have superior performances by contrast with conventional synchronous generators and induction generators, such as upstanding stability, power generation of variable speed constant frequency ( vscf ), adjusting active power and reactive power independently, and absorbing lag reactive power deeply

    交流勵磁發電機的基本結構與繞線式異步電機相同，其定子側接電網，轉子上採用三相對稱分佈的勵磁繞組，由變頻器提供對稱交流電勵磁，且勵磁電壓的幅值大小、頻率、相位、相序都可根據要求加以控制，從而可以控制發電機勵磁磁場大小、相對于轉子的位置和電機的轉速，使得交流勵磁發電機具有良好的穩定性及轉速適應能力、獨立的有功與無功調節能力和較強的進相運行能力，性能超越傳統同步發電機和感應發電機，因而有著廣闊的應用前景。
  10. The operation principle, stability and current ripple of the output filter inductor between serial and parallel modes are analyzed. a 1000 va serial and parallel combined dual buck half - bridge inverter ( dbhbi ) has been implemented to verify the analysis

    文章分析了該逆變器的工作原理、串並聯兩種運行模式對輸出濾波電感電流脈動、輸入電壓脈動、系統穩定性的影響，並以1000va雙降壓式半橋逆變器為例進行了實驗驗證。
  11. The adaptive optical transducing principle on independent variables is presented in this paper, and a new adaptive optical current transducer ( aoct ) has been developed with the new independent variables introduced to oct, in which the precise power frequency current offered by a reference model of steady state is benchmark, and the measured harmonious and transient currents from optical transducer might be adjusted adaptively applying the adaptive arithmetic, so that both the steady state and transient precision of the aoct has been improved

    論文提出了獨立量自適應光學傳感原理，並應用這種原理的一種形式? ?光電獨立量自適應光學電流傳感原理，研製了一種新型的自適應光學電流互感器（ adaptiveopticalcurrenttransducer ，簡稱aoct ） ，以穩態參考模型所提供的高精度基波電流測量值為基準，應用自適應演算法對aoct中光學傳感頭輸出的穩態電流中的基波、諧波和暫態電流測量值進行自適應校正，從而能夠綜合提高oct對電力系統穩態和暫態電流的測量精度。
  12. Our company is strong in technology, advanced production equipment, product quality, the service integrity, steadfast, a scientific system of production management and services to continually improve the ability of enterprises to innovate, is a totally independent production of fluorescent lamp, clean up lights, inductance ballasts, fluorescent tubes, three ? lights and various accessories lampholders integrated enterprise, and the company ' s products have full access to the country “ ccc ” mandatory product certification

    公司技術力量雄厚，生產設備先進，產品質量穩定，服務誠信踏實，一整套科學的生產管理及服務體系使企業創新能力不斷提高，是一家完全能夠自主生產各類熒光燈、凈化燈、電感鎮流器、熒光燈管、三防燈及各類燈座配件的綜合性企業，並且本公司產品已全面獲得了國家「 ccc 」強制性產品認證。
  13. Next, the global system architecture is presented upon the design requirements. due to the fact that constant current is required for driving led, as a result, different from conventional current - mode converter with both output voltage and inductor current feedback loop, the proposed converter adopt dual current feedback loop that both inductor current and output current are detected to provide a stable output current for led

    在整體結構設計中，與典型的電流模式採用電感電流反饋環路和輸出電壓反饋環路不同，本文針對驅動led需要電流穩定的特點，採用雙電流反饋環路，即電感電流環路和負載led電流環路，這樣就能對負載led電流做出快速響應，通過反饋環路達到穩定led電流的目的。
  14. According to the actuality of the present research on ct, this paper introduces the measurement principle of rogowski coil and analyzes the factor that influence the precision of measurement, we bring forward a new design scheme based on the rogowski coil

    本文首先介紹了國內外電流互感器發展現狀，重點對rogowski線圈測量原理進行分析，研究了線圈的穩態測量誤差以及幅頻特性、相頻特性、暫態時間響應特性，論證了羅氏線圈作為傳感器單元所具有的優良特性。
  15. It achieved good statistic and dynamic performances by using double current loop feedback control

    通過分析和比較電感電流雙環反饋模式的控制及其模擬結果，達到了較好的穩態和動態性能。
  16. The particle - enriched zone moves outwards as the rotational rate increases. by employing steady dc magnetic field to the conventional centrifugal casting method, the distribution of particles is changed. the most uniform distribution is obtained when the magnetic density is 0. 15t

    通過向常規的離心鑄造中引入穩恆直流電磁場，基體中的顆粒分佈得到改善，磁感應強度為0 . 15t時，顆粒的分佈最為均勻，磁感應強度過大時，磁場將會引起基體組織粗化。
  17. The study in various switches with high voltage, high current, fast turn - on time, low jitter, low resistance, low inductance, low erode rate and being capable of steadily work with pulse repetition - rate, is currently a subject of growing interest

    具有耐受高電壓強電流、擊穿時延短而分散小、電阻和電感小、電極燒損少以及能在重復脈沖下穩定工作的各種類型的開關元件的研製，是當前一個十分受重視的研究課題。
  18. The stability of the jet flows under strong magnetic field was explained with its velocity, induced potential and current

    從射流的感應電勢、電流、速度等方面，解釋射流在磁場中穩定的原因。
  19. Presently take the direct current voltage - stabilized source as the example introduction experiment educational reform, this experiment educational reform enable the student to obtain the twice the result with half the effort study effect, let the student achieve the knowledge from the rational cognition the perceptual cognition

    現以直流穩壓電源為例介紹實驗教學改革，該改革使學生得到了事半功倍的學習效果，讓學生將知識點從理性的認知達到了感性的認知。
  20. In this paper, for the first time, it is proved that oct is an open loop system, so that the adaptive optical transducing principle on independent variables and the solenoid collecting magnetic field optical transducing principle are presented. based on the above two principles, the methods are gained to improve the precision and stability of oct, and the new adaptive optical current transducer ( aoct ) had been developed

    本論文在深入研究oct的原理、結構和運行特性的基礎上，首次在理論上證明了oct是開環系統，並首次提出了獨立量自適應光學傳感原理和螺線管聚磁光學傳感原理，進而得到了提高oct測量精度和長期運行穩定性的有效方法…光電獨立量自適應光學傳感原理和螺線管聚磁光路結構，並以此研製成功了新型的自適應光學電流互感器（ aoct ） 。
分享友人
分享到 Line

分享到臉書