穿孔位置 的英文怎麼說

中文拼音 [chuānkǒngwèizhì]
穿孔位置 英文
punch position
  • 穿 : Ⅰ動詞1 （破; 透） pierce through; penetrate 2 （通過孔、隙、空地等） pass through; cross; go thro...
  • 位 : Ⅰ名詞1 （所在或所佔的地方） place; location 2 （職位; 地位） position; post; status 3 （特指皇帝...
  • 置 : 動詞1. （擱; 放） place; put; lay 2. （設立; 布置） set up; establish; arrange; fix up 3. （購置） buy; purchase
  • 穿孔 : 1 （鉆孔; 鑿孔; 打孔） bore a hole; punch a hole; punching; piercing; tresis; key punching 2 [醫...
  1. A line of punch positions parallel to the y datum line of a punch card

    和卡片的y基準線平行的一行穿孔位置。
  2. In this paper, firstly the macro parameter of the series connection app was comprehensively analyzed, among which the trajectory location of the bullet emission and the terminal velocity of the bullet were mainly analyzed, and the feasibility of the series connection app to cope with explosive reactive armor was demonstrated. and then the macro design about the head of the series connection app was made, among which a particular analyse about the bullet " s launching process was made, from which we concluded the relation between the thickness of the airproof loop and the velocity of the bullet detached from the carrier and the relation between the length of the bullet and the velocity of the bullet detached from the carrier and the relation between the length of the bullet and the burning rate of the powder and the relation between the length of the bullet and the maximum pressure of the emission hole and the relation between the length of the bullet and the emitting time of the bullet, and the reasonable str ucture of the head of the carrier and bullet were designed, then the intensity of the head of the carrier was checked out using of the software of ansys

    本文首先對子母式穿甲彈總體參量作了全面的計算分析，其中主要分析了子彈射出的彈道位置和必要的子彈著靶速度，論證了子母式穿甲彈對付爆炸式反應裝甲的可行性，然後對子母式穿甲彈彈頭部進行了總體設計，其中主要對子彈的發射過程進行了詳細的分析，得出了母彈彈頭部發射孔內閉鎖環厚度與子彈飛離母彈速度的關系、子彈長度與子彈飛離母彈速度的關系、子彈長度與火藥燃燒率的關系、子彈長度與母彈彈頭部發射孔內最大壓力的關系以及子彈的長度與子彈發射所需時間的關系，設計出了合理的母彈彈頭部結構和子彈的結構，並利用ansys有限元分析軟體對母彈彈頭部的強度進行了校核。
  3. The technology, which is developed on the basis of perfora ting techniques for oil wells and cement injection techniques, can not shoot thr ough the frozen pipe wall at predetermined ground location using energy - gatheri ng - blasting techniques, but also consolidate shaft wall rock by cement injectio n and filling along the frozen pipe and perforated hole s trajectories, achievi ng leakageproof of shaft walls and reducing vertically - added force

    它利用聚能射孔爆破技術，在預定地層位置將凍結管射穿，同時在地面利用凍結管及射孔彈道對特定地層進行注漿充填加固，既可實現井壁堵漏，又能減少由於地層沉降對井壁的垂直附加力。
  4. Based on research of the antenna assemble procedure, the simulation model of the reflector is set up and error modeling and simulation of position of stick holes, grid bar acrossing the hole and rms of reflector face are achieved

    在分析柵格天線裝配過程基礎上，建立了其反射面裝配的模擬模型，並對柵支板中心圓孔位置誤差、柵條穿人誤差和柵面誤差進行了建模與模擬計算。
  5. Cinematography - image area produced by 65 mm 5 perforation motion - picture camera aperture and maximum projectable image area on 70 mm 5 perforation motion - picture prints - positions and dimensions

    電影. 65 mm 5穿孔電影攝影機片窗新形成的畫面區域和70 mm 5穿孔電影拷貝的最大可放映畫面區域.位置和尺寸
  6. Across the width of the tape there are usually eight positions in which we can punch a hole.

    在紙帶寬度之內，通常有8個可供穿孔的位置。
  7. Punched paper cards for information processing ; dimensions and location of rectangular holes

    信息處理用穿孔紙型卡片.第2部分:矩形孔的尺寸和位置
  8. Specification for paper tape for data processing - dimensions and location of punched holes in paper tape

    數據處理紙帶規范.第2部分:紙帶穿孔尺寸和位置
  9. In addition, the paper presented the influence of different shutter positions to the simple expansion cavity muffler

    此外，研究了不同穿孔板位置對簡單膨脹腔消聲器排氣噪聲的影響。
  10. This instrument is used for the detection of localised moulding faults, insufficient membrane thickness, perforations, etc.

    它是特別為塑膠零件的生產線高速生產而設計的，該儀器用於發現鑄模缺陷的位置，膜的厚度缺陷和穿孔等。
  11. In computing, ( a ) to replace all the binary digits in a storage device by binary zeros, ( b ) to replace all hole patterns on a punched paper tape by holes in every position

    在計算技術中， （ 1 ）用二進制零替換存儲設備中所有的二進制數; （ 2 ）在穿孔紙帶上的每個位置上都穿孔，以代替所有的穿孔模式。
  12. Automatically assigns lead - ins / lead - outs, pierce locations, corner features ( corner loops, radius corners, tabbed corners ), and micro joints based upon user defined settings

    按用戶設置自動分配導入/導出，穿孔位置，角特徵（周角，半徑角，跳躍角） ，及微連接
分享友人
分享到 Line

分享到臉書