立軸給進系統 的英文怎麼說

中文拼音 [lìzhóugěijìnxìtǒng]
立軸給進系統 英文
spindle head feed system
  • 立 : 動1 （站） stand; remain in an erect position 2 （使豎立; 使物件的上端向上） erect; stand; set up...
  • 軸 : 軸Ⅰ名詞1. （圓柱形的零件） axle; shaft 2. （對稱部分的直線） axis 3. （圓柱形的纏繞器物） roller; spool Ⅱ量詞（用於纏在軸上的線以及裝裱帶軸子的字畫）
  • 給 : 給Ⅰ動詞1 （送對方某物; 使對方得到） give; grant 2 （用在動詞后 表示交與 付出） pass; pay 3 （叫; ...
  • 進 : 進構詞成分。
  • 系 : 系動詞（打結; 扣） tie; fasten; do up; button up
  • 統 : Ⅰ名詞1 （事物間連續的關系） interconnected system 2 （衣服等的筒狀部分） any tube shaped part of ...
  • 系統 : 1. （按一定關系組成的同類事物） system 2. （有條理的;有系統的） systematic
  1. The paper establishes mathematics model of electromagnetic heating system of eddy current field and temperature field, and gives corresponding discrete format with elements as eight nodes, hexahedron equal cell, through calculating eddy - current field to gain the internal heat source that the temperature field needed, to use discrete method to solve the problem of induction - heating part ' s temperature field by axial symmetrical electromagnetic, and then to analyze the characteristic of instantaneous temperature field

    本文建立了電磁加熱系統的渦流場和溫度場間接耦合的數學模型，分析了不同頻率下渦流和溫度的分佈情況，並以八節點六面體等參元為例給出了渦流場對應的離散格式，通過計算渦流場獲得溫度場所需要的內熱源強度，加熱部件的溫度場以軸對稱格式進行離散求解，並對瞬態溫度場有限單元法的求解特點進行了分析。
  2. So, in the paper, proceeding from the automatic control of extrusion velocity and based on the basic control strategy presented firstly, the relation among parameters of the process such as pressure, temperature and displacement is investigated, and the model of the process has been built using system identification method. then, a corresponding controller is designed together with its control algorithm, and the control system is proved viable and effective by the results of simulation on the control system. in the end, the problem of the realization of the control system is discussed by using modularization method. the hardware of the control system is designed and a sofeware with a perfect manmachine interface is developed, too

    因此，本文從擠壓速度的控制出發，首先探討並確立了本系統的基本控制策略；然後根據此控制策略的必然要求，對該工藝擠壓過程所涉及到的擠壓力、溫度、擠壓軸位移等參數間的關系進行了深入研究，利用系統辨識方法建立了擠壓過程關鍵階段的數學模型；在此基礎上完成了相應的控制器設計，給出了控制演算法，並對所設計的控制系統進行了模擬。
  3. Second, based on the theory of error separation, the mathematical model, which is used to extract the surface flaw of axis - like parts, is given briefly. third, the designs of hardware and software in the system are explained respectively. fourth, the models and algorithms for appraising the surface flaw of axis - like parts are established by the methods of pattern recognition and neural net

    第一，本文論述了該課題研究的必要性及應用開發的價值：第二，簡要介紹了基於誤差分離理論建立起來的提取軸（孔）類工件表面缺陷的數學模型；第三，對該系統的硬體和軟體設計分別進行說明；第四，運用模式識別和神經網路等方法建立軸承工件表面缺陷評判模型和演算法，並給出了各種評判方法的比較。
  4. Compared with the ordinary optimization algorithm of calibration, this algorithm is simple, less computational and high accuracy. finally, the paper put forward the ranging method based on similar triangle principle. it gives two ranging models according cooperation object vertical in the optical axis or not vertical in the optical axis and does experiment

    最後，本文提出了一種基於相似三角形原理的測距方法，根據合作目標與攝像機主光軸垂直與不垂直兩種情況，給出了兩種測距模型，建立實驗系統並進行了實驗，通過近距離段與遠距離段的測距結果與誤差分析驗證了此方法的有效性，能夠準確的確定合作目標的位置，計算簡單，測量精度高，具有重要的理論意義和工程使用價值。
分享友人
分享到 Line

分享到臉書