端部接縫 的英文怎麼說

中文拼音 [duānbùjiēféng]
端部接縫 英文
end joint
  • 端 : Ⅰ名詞1 （東西的頭） end; extremity 2 （事情的開頭） beginning 3 （門類; 方面） item; point 4 （原...
  • 部 : Ⅰ名詞1 （部分; 部位） part; section; division; region 2 （部門; 機關或組織單位的名稱） unit; mini...
  • 接 : Ⅰ動詞1 （靠近;接觸） come into contact with; come close to 2 （連接; 使連接） connect; join; put ...
  • 縫 : 縫名詞1. （接合處） seam 2. （縫隙） crack; crevice; fissure; slit
  • 端部 : telos
  • 接縫 : seam; jugum; joint; kiss; unwelded joint接縫刨 jointer; 接縫構造 seam construction; 接縫灌漿 joint grouting
  1. Breakages originated chiefly at knots in the lower edges of the 2x8 inch timbers.

    大部破壞發生在2X8英寸木板的下端接縫處。
  2. As an application of this fem preprocessing system, the simulation on the welding process of missile ’ s oil box was performed, in which the effects of the welding sequences of four web plates and welds on each web plate are primarily analyzed. the simulation results show that the deformations under varied welding sequences are almost the same. downward deflection deformation is obtained along the weld longitudinal direction in the structure as well as upward deflection deformation along the weld traverse direction

    對于某型號導彈油箱結構焊接過程的數值模擬計算，主要考察了每塊立板上各段焊縫焊接順序的調整、四塊立板之間不同的焊接順序以及焊接起始端的選擇對結構焊后變形的影響規律，模擬結果表明:壁板在各種焊接順序下的整體變形規律基本相似，即焊後壁板沿焊縫縱向發生了向下的撓曲變形，中部向下變形量最大;沿焊縫橫向發生了向上的撓曲變形，壁板兩端部變形量較大，且壁板前端變形大於壁板後端。
  3. The welding technology of francis turbine runners is optimized from the view of subsection welding and local heating by numerical simulation. the result shows that welding residual tensile stress appears in the weld and its area nearby, and peak stress appears in the dangerous area of blades after practising quondam welding technology ; welding residual tensile peak stress in the dangerous area of blades can be decreased by welding both ends earlier and then welding middle section later during subsection welding, and decreasing effect on welding residual stress of the subsection welding is related to the weld length of blade outlets and welding direction of each subsection ; decreasing effect on residual stress of the local heating is direct proportional to heating time, heating temperature, heating area, and inversely proportional to cooling area, and welding residual tensile peak stress in the dangerous area is decreasing trend earlier, and then increasing trend later with heated location increased

    本文利用數值模擬手段對轉輪的焊接工藝從分段焊和局部加熱兩個方面進行了優化，結果表明:採用普通工藝焊接時，葉片焊后殘余拉應力出現在焊縫及其附近區域，並且在葉片出水邊的熔合線附近（危險區域）出現了峰值;在採用優化的分段焊時，先焊兩端后焊中間的方法可以降低葉片危險區域的焊接殘余拉應力峰值，降低效果與葉片出水邊焊段長度、焊縫各段的焊接方向有關;局部加熱法降低轉輪危險區域殘余應力的效果主要與加熱時間、加熱溫度以及加熱面積成正比，與冷卻面積成反比，並且危險區域的殘余應力隨加熱區域的增大呈先降低后升高的趨勢。
  4. The conclusion of reappearing analysis is that crane bridge be used as usual because main weld maximum stress of upper cover plate of main beam lower than yield limit though it higher than permissible stress. inner stress of secondary beam was over ultimate strength, and deforming is ultra big. so it was unfit for produce and secondary beam must be changed

    再現分析得出的主要結論為：橋架的主樑上蓋板主焊縫的最大應力超過了許用應力，但小於屈服極限，可以繼續投入使用；副梁內部的應力遠遠超過了強度極限，變形特別嚴重，不能滿足生產要求，因此更換新的副梁；端梁內部的應力超過了屈服極限，小於強度極限，在應力較大的位置焊接補強板；投入使用后，要對整個橋架進行定期檢查。
  5. Breakages originated chiefly at knots in the lower edges of the 2x8 inch timbers

    大部破壞發生在2x8英寸木板的下端接縫處。
  6. It has the advantages of delivering routes between the layer 3 which are connectionless and the layer 2 which are connection - oriented. through constant research and countless experiments, the method of seamless integration with customer intranets has been found out, so that we only buy the customer equipment once, and the upgrade of the network only needs to modify the configurations but not needs to change the consumer equipment

    Mpls改進了專線組網的缺點，兼有無連接的第三層路由和面向連接的第二層轉發的優點，通過研究和不斷實驗，找到了用戶內部網無縫集成的方法，從而使用戶端的設備投入一次到位，網路升級只需修改一下配置，用戶端硬體不用做任何改動。
分享友人
分享到 Line

分享到臉書