等溫加熱 的英文怎麼說

In section one, by using fice scheme and time - gcm, a model of trace gases and oh airglow affected by gravity wave is set up, then the propagation of nonlinear gravity wave and the effect on trace gases and oh airglow are analyzed. the result shows gravity wave excited by tropospause forcing can propagate stably to the mesosphere through the stratosphere so that energy and momentum can be transferred from one region to another. in this process, gravity wave undergoes growth, overturning, convection and breaking

在第一部分的工作中，利用全隱歐拉格式和全球熱層-電離層-中間層-電動力學環流耦合模式（ time - gcm ） ，對重力波的非線性傳播及其在傳播過程中對中高層大氣中氧族和氫族成分和與之密切相關的oh氣輝輻射的影響進行了數值模擬，結果表明，從對流層向上傳播的重力波經歷了產生、發展、飽和、對流產生直至破碎的非線性演化，大氣的非等溫結構加速了重力波在中層頂區的破碎，重力波的非線性傳播是小尺度對流和湍流產生的一個重要的源。

Abstract : the formation technologies, the structure and properties of tcs microporous man - made yarn - kind new polyester fibre which was spinned in tcs with some micrometallic - oxide have been studied. the results indicate that the rheological behaviour and spinnability of commixed polyester melt, and the structure and properties of the fibre, are relative to the spinning temperature, melt pressure, microporpus size for spinning, formation conditions, thermo - vascellum temperature, thermo - vascellum position and rolling speed, besides the viscosity of polyester cuts, coacervation particles, adding amount and size of micrometallic - oxide

研究表明， tcs微孔化共混聚酯熔體在成型加工中的流變行為和可紡性，及其纖維的結構性能除了與原料切片的特性粘度、凝聚粒子和共混聚酯中超細金屬氧化物微粒的添加量、粒徑等因素的影響有關外，還與紡絲溫度、紡絲熔體壓力、噴絲板微孔尺寸、冷卻成形條件、熱管溫度、熱管安裝位置以及卷繞速度等因素的影響密切有關。

Medium frequency induction heating equipment are used in metal melting, temperature keeping, diathermic technology, metal - heat processing brass soldering, quenching, tempering and sintering

中頻感應加熱設備適用於各種金屬熔煉，保溫，透熱，金屬熱處理，釬焊，淬火回火，燒結，釬絲鋼絲等。

Recent experiments have succeeded in obtaining oscillations from the new system, with frequencies of 66hz and 23hz for the cases with helium and nitrogen as the working fluids, respectively. the traveling wave system is expected to be one of the good candidates as a driver for pulse tube refrigerator, leading to a thermoacoustically driven pulse tube refrigerator without any moving component

還利用deltae對環路部分進行了數值模擬分析，著重討論了系統的起振臨界溫度與臨界加熱功率、效率與加熱溫度的關系、噴射泵的作用以及不同工質（氮氣和氦氣）的比較等，得出一些有益的結論。

The globalization course was that the preformed texture recrystallized and became the granular equiaxed grain, when the temperature rose and the holding time prolonged, the granular grain melted at some area and at the liquid - solid interface the grain globalized at the role of the curvature overheated

過程機制為：擠壓形變組織在加熱過程中首先發生再結晶長大變為顆粒狀等軸晶；隨溫度升高和保溫時間延長，等軸晶發生局部熔化，液固界面的曲率過熱使晶粒外形向球狀轉變。

Usage : manufacture tungsten wire, frame of grid, elicit wire, bracket, unsag tungsten wire, mould rods in high temperature, eradiate cathode, electrodes, bracket of heating

用途：用於製造鎢絲柵極邊桿引出線支架不下垂鎢絲，高溫定型桿發射陰極電極加熱子支撐桿等。

Series of guowei dry - method composite machines as new product are explored with our many years ' experience, the requirement of the users. the first metal of this machine is adopted with : photo - ecectricity auto. tracking " correcting deviation equipment, magnetic powder tension control. pneumatic back pressure shifting blade, oven temperature controlled qutomatically, big roll with oil heating, coating composite pneumatic control as well as double frequency governor etc. it will make the machine with fast speed, lower voice, low polluted by air, shout consumptionfor energy, stable working etc. especially suitable for al - foil with smooth surface and no enough firming, glass paper, polyester ect. the composite material with hard strength, fireproof, anti - ventilation, anti - fatty, frozen, dudrable steam etc character. it is widely used in food, pharmacy, as well as daily articles to package

「國偉」 、系列乾式復合機，是我廠根據多年的復合機製造經驗及結合客戶需求，開發的新產品，該機第一基材採用了「光電自動跟蹤」糾偏放卷裝置，磁粉張力控制、氣動背壓移動式刮刀、烘箱溫度分段自動控制、大輥筒導熱油加熱、上膠復合氣動控制及雙變頻調速技術，使該機具有復合速度快、噪聲低、空氣污染小、能耗低、運行平穩等特點，適宜於表面光滑的鋁箔玻璃紙聚酰胺等與聚乙烯、聚丙烯等薄膜的復合，復合薄膜具有強度高、防水、防透氣、防油脂、可冷凍、蒸煮等優點，廣泛應用冷凍食品、乾燥食品、醫藥品及日用品的包裝。

The water heater shall have a self - diagnostic control that monitors and indicates power on, no power or control failure, start - up failure, high - limit operation, sensor failure, defective upper element, or defective lower element

這種熱水器應該配置自診斷控制裝置，能夠監控和顯示通電、停電、控制裝置故障、啟動故障、高溫運行、感應器故障、上部加熱元件或下部加熱元件故障等狀態。

This paper use the ncep / ncar day - to - day reanalysis data of 500hpa high field and so on, choose ural mountain, baikal, okhotsk as the key district, the mid - high latitude of eurasia circulation courses that have long duration ( scale of time is middle, namely during 10 - 30 day ), maybe continue continuously after being intermittence of 1 - 2 days in middle, appear repeatedly is for research object, define an index " i " of the circulation pattern over mid - high latitude of eurasia. a method is proposed to identify the summer typical persistent circulation pattern at 500hpa levels over eurasia mid - high latitude. the climate characteristics of those typical persistent circulation patterns are studied

本文利用ncep / ncar再分析逐日500hpa高度場等資料，選擇烏拉爾山、貝加爾湖、鄂霍次克海這三個地方作為關鍵區，以夏季歐亞中高緯度持續時間長（時間尺度屬于中間時間尺度，即10 ? 30天之間） 、中間可能會間歇1 、 2天然後又繼續持續、反復出現的環流過程為研究對象，定義了一個夏季歐亞中高緯流型指數，在此基礎上提出了一種對夏季歐亞中高緯500hpa典型持續流型的界定方法，研究了典型持續流型的氣候特徵，分析了流型指數的年代際變化，以及對應不同階段、不同流型的降水場、加熱場、海溫場等的主要特徵。

This product is used for that in order to reach even and effective desulfidation for rubber powder, put pulverous crosslinked rubber, softener, activator and water into the pot, heat hermetically and mix contlnuously, adopted key equipment for the technology of high temperature dynamic desulfidation

該產品用於將粉末狀硫化膠與軟化劑、活化劑及水等置於罐內，在連續攪拌下密閉加熱，以使膠粉達到均勻有效膠硫目地，是採用高溫動態脫硫新工藝的關鍵設備。

We select ni / cr alloy resistor as element together with ceramic embedding hearth ; select small flat - and - disc heat - even hubby ceramic sample holder, select ni / cr & ni / si thermoelectric couple ( type k ) as thermoscope with threads 0. 5 mm in diameter which is installed in the middle of the holders symmetrically ; select aluminum silicate fire - retardant fiber as materials for heat preservation ; design some hardware, for example temperature controller & transporter, signal amplifier etc ; design controlling curve to heat stove ; and introduce the method of least squares nonlinear regression and subsection function to deal with data. in order to obtain the reasonable operation conditions and operation curve, we have also done many theory analysis and experiment discussions

通過理論和試驗探討，選用鎳鉻合金電阻絲作為加熱元件，配以陶瓷質埋入式爐膛；選用陶瓷質小尺寸扁平?圓盤均熱塊體型樣品支持器；選用0 . 5mm絲徑鎳鉻?鎳硅熱電偶（ k ）作為測溫元件；熱電偶對稱安置在樣品支持器容器的中部；選用硅酸鋁耐火纖維作保溫材料；合理選用和設計了溫度控制器、溫度變送器、信號放大電路等硬體；採用升溫曲線來控制爐膛供熱過程；採用最小二乘法非線性回歸與分段函數相結合的曲線模擬方法，進行圖形處理。

The composite has excellent performance of water retaining, that the adsorbed water of 85 % is retained after being dried 10 days at the room temperature, and the adsorbed water of 45 % is retained after being dried 24 hours at 60 the factors influencing on water absorbency for the superabsorbent composite such as the kinds and concentration of starch, clay, crosslinker, initiator, the external salt solution and hydrolysis degree are investigated in this paper

該超吸水性復合材料在室溫下乾燥10天後的保水率為85 ，在60 2條件下加熱24小時后的保水率為45 。本文較詳盡地探討了超吸水性復合材料的合成條件，並系統地研究了影響超吸水復合材料吸水倍率的各種因素。例如：粘土的種類及粘土的用量、澱粉的種類及澱粉的用量、交聯劑的用量、引發劑的用量、水解度（氫氧化鈉的用量） 、水解時間、外部鹽溶液的種類及濃度等條件。

An integrated process of wastewater treatment and utilization is presented. the process is made up of heating the soft water of room temperature by high temperature printing and dyeing wastewater via heat exchangers, reusing the low level base decrement wastewater of water washing for dust control and desulphurizing of stack gas and anaeration - aeration biological treatment of printing and dyeing wastewater. this process has fair economical benefit on the principle of so called waste control by waste itself. this might be an ideal process for printing and dyeing wastewater treatment and disposal, the effluent of this process is quite enough to meet the requirement of urban sewer collector. additionally also many advantages are attractive such as the complete return of biological sludge to digestion, no chemicals dosage and free of secondary pollution

介紹了高溫印染廢水通過熱交換加熱常溫軟水、低濃度堿減量水洗廢水用於煙道氣除塵脫硫、厭氧-好氧處理一般印染廢水等印染廢水綜合處理技術，該技術具有較好的經濟效益，達到了以廢治廢的目的，生物污泥全部迴流硝化，不加任何藥劑，無二次污染，處理后水質達到城市截污管網標準要求，是一種較為理想的印染廢水處理工藝。

When the two reactants were simply mixed by crush, they reacted violently and produced carbon spheres with a diameter of 50 - l00nm and sodium chloride ( nacl ) was encapsulated within the outer amorphous carbon shells, which could be confirmed by sem and tem. by annealing at 1400 ? to drive the encapsulated nacl away, hollow carbon spheres were left with a novel mesoporous structure, as presented in hrtem

實驗中將兩種反應物通過直接擠壓混合后加熱反應，得到的無定型球狀碳材料經tem照片證實直徑為50 - 100納米，而且中間包裹氯化鈉（ nacl ）顆粒； xrd等結果顯示，高溫退火併徹底清除nacl后形成的中空碳球已經部分石墨化。

At present our main products : all kinds of the glass vacuum cups, heating element of tempering machine, kevlar rope, cutting machine table carpet, brush roller of glass washing machine, rubber roller, castor wheels, silicon rope for the laminated glass, flood & squeegee bar for the colour glazed glass, glass clamps etc

目前主要產品有：各類玻璃真空吸盤、各種類型加熱爐絲、耐高溫陶瓷件、耐高溫纖維繩、絲印機回墨刀、刮刀、萬向輪、傳送膠輥、清洗機毛刷輥、自動切割線用毛氈、彎夾玻璃真空硅膠管、真空袋、玻璃吊夾等。

Ensure safety inusing the instrument, it is installed with unbalanced unit, gate lid, overspeed and overtemperature protection device. and colding & heating dual control temperature unit can meet the need of component blood ' s separating temperature

設有不平衡、超速、超溫、門蓋等多種保護、確保儀器安全使用，製冷加熱雙路控溫滿足了成分血液分離溫度。

From the feature of the force and deformation of the tpih, 5 different elements are used to mesh the different zones of the tube, which are structural beam 3d elastic 4, structural pipe plastic straight 20, structural pipe elastic elbow 18, structural shell elastic 4 node 63 and contact 3d pt - to - surf 49 ; the contact problem is assumed to be flexible - to - flexible ; the temperature field is assumed to be body load. a mechanical model corresponding to reality has been established for numerical simulation. based on the above, the 3 - d fem numerical simulation of tpih has been carried out by using the ansys program

針對加熱彎管過程的受力和變形特點，採用三維梁單元、三維塑性直管單元、三維彈性曲管單元、三維殼單元與三維點對面接觸單元等5種不同的單元分別對管毛坯不同區域進行劃分，並對接觸單元採用柔體-柔體的處理方法，將溫度場作為體載荷處理，建立了符合實際的加熱彎管問題數值模擬力學模型：在此基礎上，應用商用軟體ansys對加熱彎管過程進行三維有限元模擬與研究，獲得了成形時推力、彎矩、支撐力大小及其變化趨勢。

This text completely and systematically studies the status and the development of the pyrolysis and the fluidization of biomass, which distill the bio - oil in the domestic and international area, as well as the existing problems. this thesis primarily include following aspects : ( l ), by experimenting and measuring the energy ( heat value ) and the content of c, h, n chemical element of right 20 kinds of common biomass, on the base of the experimental result, and respectively established the biomass energy predict experiment formula with the element of h and c is from change, and passed the ro. os examination, which provides the basis and convenience for flash pyrolysis fluidization device energy to convert the rate to compute with biomass energy utilization calculation ; ( 2 ), proceeded the tg and dtg experimentation equal velocity ( 10 ? / min, 20 ? / min, 40 ? / min, 60 ? / min ) heating and constant temperature heating by studying on eight kinds of biomass samples, according to the experimental data and arrhenius formula, we established the dynamics model of pyrolysis of, then, using the goast - redfern and p function, we also solved the dynamics parameters and analyze out every kind of biomass ' s frequency factor and parameters of activation energy, and established the every kind of dynamics model of pyrolysis of biomass, all of these provide the theories and basis to make sure the reactor ' s flash pyrolysis work temperature scope design and the describing of pyrolysis reactor dynamics ; ( 3 ), in order to study and ascertain the process of heat completely getting to pyrolysis time of varied size biomass particles, we observed and measured the ratio of length and diameter ( l / d ) with the varied biomass through electron microscope, we concluded the l / d ratios usually is from 5. 0 to 6. 0, the average is 5. 3 ; ( 4 ), we studied the process of biomass transiting and the theory of complete pyrolysis time with the theory of complicated heat field, we got the time ( t ) of the varied size biomass particles arriving to complete pyrolysis, and we knew that the complete pyrolysis time and the time which get to the biggest production ratio are identical, all of these studies provide the theory base for design and forecasting the flash pyrolysis reactor solid state resort time ; ( 5 ), according to the above experiment result, synthesize to make use of the engineering the mechanics, engineering the material, machine the design to learn the principle, deduce, establish the theory of rotation cone flash pyrolysis reactor material resort time ( t ) and reasonable rotation velocity ( or frequency ) relation theory ; and ( 6 ), we gave the reactor ' s smallest cone angle certain, reactor cone wall strength design theory, the reactor production ability theory, the power design method and the critical rotation velocity theory

本文較全面、系統地綜述了國內外生物質熱解液化制取生物燃油技術研究發展現狀及存在的問題，主要研究內容有： （ 1 ）實驗、測定了20種常見生物質的能量（發熱量）和c 、 h 、 n元素含量，根據實驗結果分別建立了以h和c為自變量的生物質能量預測經驗公式，並通過r _ （ 0 . 05 ）檢驗；為閃速熱解液化裝置能量轉化率計算和生物質能量利用率計算提供了依據和方便； （ 2 ）選擇了8種生物質試樣作了等加熱速率（ 10 min 、 20 min 、 40 min 、 60 min ）和恆溫加熱的tg和dtg實驗，根據實驗數據和阿倫尼烏斯公式建立了生物質熱解反應動力學微分方程，並採用goast - redfem積分法和p函數對其動力學參數進行了求解，解析出各種生物質的頻率因子和活化能參數，進而建立了各種生物質的熱解動力學模型，為科學確定反應器的閃速熱解工作溫度范圍及熱解反應動力學描述，提供了理論和依據； （ 3 ）為研究和確定不同尺度的生物質顆粒中心達到全熱解的時間，在體視顯微鏡下對不同粒度的生物質顆粒的長徑比進行了實驗觀察和測定，得出生物質的長徑比（ l d ）一般在5 . 0 6 . 0之間，平均為5 . 3的結果； （ 4 ）採用復雜溫度場傳熱學理論對生物質傳熱過程及充分熱解時間理論進行了研究，解析推導出了不同尺寸生物質顆粒中心溫度達到充分熱解溫度的時間（ t ） ，得出了理論推導的充分熱解時間與最大產油率的熱解時間相一致的結果，為閃速熱解反應器固相滯留時間設計和預測提供了理論依據； （ 5 ）根據上述實驗結果，綜合運用工程力學、工程材料、機械設計學原理，推導、建立了轉錐式閃速熱解反應器物料滯留時間（ ）與轉速（或頻率）合理匹配理論； （ 6 ）提出了轉錐式閃速熱解反應器的最小錐角設計、錐壁強度設計、生產能力設計理論和功率計算方法及臨界轉速理論等。

Mapping rheogram and analyzing thixotropy of fresh cement paste with different superplasticizers by measuring the rheologic parameters such as shearing stress 、 yield stress and plastic viscosity. using multi - channel isothermal calorimeter together with non - contacting electrical resistivity device, traditional hydration heat testingl and electrical resistivity testing were connected. using temperature - sensitive of traditional hydration heat model and structure - sensitive of structure formation model, instantaneous formation condition of paste structure was described exactly

`採用多通道等溫量熱儀以及無電極電阻率測定儀，將傳統的水化熱測試與電阻率測試結合起來，運用水化熱的熱敏感性與結構形成的結構敏感性，更加真實地描述了水泥漿體初始結構的瞬時形成狀態;系統全面地研究了高效減水劑對水泥水化過程的調控作用;運用微觀測試方法，深入探討了高效減水劑對水泥水化過程的影響。

It has given the solutions how to troubleshoot the problem of amlcd at low - temperature environment, including thermal power theoretical calculation of ito heater - film, the technology of built - in ito soft heater - film in lcd, and heat control circuits at low temperature, etc. this paper presents a way to solve the problems, namely, lcd response slowly, and even not work in low temperature environment. in addition, this paper also researches into the features of vibration, shock and emc, and gives the means of how to solve them by reinforcing rigidity, shielding and filter etc

本文在深入研究液晶顯示器溫度、振動、沖擊、電磁兼容、潮濕等環境特性的基礎上，解決了液晶屏在惡劣環境下工作的具體問題，提出了有源液晶顯示器的低溫解決措施，包括ito加熱膜加熱功率的理論計算、液晶屏內置ito柔性加熱膜工藝、低溫加熱控制電路等，較好地解決了模塊化液晶顯示器在低溫環境下出現的響應速度慢，甚至不能使用的問題。