管壁熱阻 的英文怎麼說
中文拼音 [guǎnbìrèzǔ]
管壁熱阻
英文
wall resistance-
As ammonia built up in the water gas purification system reacts with a part of condensate on the inner wall of the heat exchanger tube passes, and the salt solution formed cools down and crystallizes in the tube passes, the resistance in the shift conversion section increases exceedingly
摘要由於水煤氣凈化系統積累的氨與部分冷凝水在換熱器管程內壁反應形成的鹽溶液在管程內冷卻結晶，造成變換工序阻力異常增大。7 thermocouple and thermal resistance special in stove pipe, burning furnace and the wall of boiler
7爐管道焦爐鍋爐爐壁專用熱電偶阻The interior size and the calorific capacity of the borehole are much smaller, moreover the temperature change is slow, so usually we can neglect the influence of calorific capacity but to consider according to the heat transfer in steady state process, thus we can establish one - dimensional and the two - dimensional thermal resistance model in the borehole
而在鉆孔內部，包括回填材料，管壁和管內傳熱介質，與鉆孔外的傳熱過程相比較，由於其幾何尺寸和熱容量要小得多，而且溫度變化較為緩慢，因此通常可以忽略其熱容量的影響而按穩態傳熱過程來考慮，建立了鉆孔內的一維和二維的熱阻模型。Adopt advanced technic of f4 whole cold - press to moulding and heat melt to process to make, let the lining no slot to link withal cheek by jowl connect with exterior metalpipes wall, in the state of allowwing to work keep to distort in - phase, thereby to enhance using - life of lining in the working status of opposite high temperature high vacuum, stop the ecumenic pad fluorin pipes using in condition of cold and heat alternate and minus tension to come into being the matter of padding fluorin floor shrivel to jam the flowway and plastic rip, its perfect choice use to transport medium of strong corrosive strong oxidation by modern chemical - industry corporation
採用氟塑料f4整體冷壓成型及熱熔加工等先進技術製造，使內襯層無縫搭接且與外層金屬管壁緊密粘接，在允許工作狀態下能夠保持同步變形，從而提高了襯里層在相對高溫高真空度的工況下的使用壽命，杜絕了一般襯氟管在冷熱交替，及負壓的條件下使用易產生襯塑層鼓癟阻塞流道及塑料拉裂的問題，是現代化工企業在輸送強腐蝕強氧化介質理想的選擇。After thermodynamic calculation on several operation conditions of the furnace, cold - state flow and resistance mensuration, the combustion of the tubular - furnace hearth was changed into swirl and addition of radiate cylinder and oxygen content detection minish 1. 25 surplus air to less than 1. 15, improving the combustion condition and convection and radiate heat transfer efficacy, resuling in reducing the waste - gas temperature 45, decreasing exhaust gas loss, and saving fuel by 6 %
摘要通過對加熱爐幾種工況進行熱力計算、冷態試驗的流場分佈及阻力測定和熱態試驗的爐膛溫度場分佈及管壁溫度等參數的測定，確定將管式加熱爐爐膛內直流燃燒改為旋流場燃燒和增加輻射筒，增設煙氣含氧量分析，可以將燃燒的過剩空氣系數從1 . 35減小到1 . 15以下，極好地改善爐膛內的燃燒狀況和對流輻射傳熱效果，從而降低排煙溫度45 ，減少加熱爐排煙損失，節約了煤氣量6 %以上。Specification for flexible insulating sleeving - specification requirements for individual types of sleeving - heat - shrinkable polyolefin sleeving, dual - wall, not flame retarded - heat - shrinkable sleeving, dual wall, not flame retarded, polyolefin
絕緣軟套管規范.各種型號套管的規范.雙壁不阻燃聚烯烴熱收縮套管There are a lot of advantages when inner trachea applied in air pre - heater, such as the improvement of the temperature of pipe, the low consumption of metal, except for the increment of flow resistance. according to many related papers, it is more proper inner trachea with the structure of short distant between two whorls and shallow depth of whorl. it can enhance heat transfer with smaller flow loss
內螺紋管是一種異形管，和光管相比，管內側的換熱系數大大增強了，應用於空氣預熱器可以起到提高總傳熱系數、節約受熱面金屬消耗量的目的；同時提高了管壁溫度，能夠減輕低溫腐蝕的程度和速度；不足之處是帶來了更大的阻力損失。Taking some tubular air pre - heater used in one boiler whose capacity is 130 t / h as an example, new blue print with inner trachea is completed by means of computer program. several key design variables may be changed, such as diameter of pipe and velocity of flow of gas. these cases have been considered, and their results have also been compared with each other
比較了幾個重要的設計變量，如外管徑、煙氣流速等參數變化時，總傳熱系數和空預器本體管子總重量，阻力損失以及最低管壁溫度等幾個重要設計結果的變化趨勢，對內螺紋管空氣預熱器的設計具有借鑒意義；其間還分析了內螺紋管與光管在設計時的不同之處；最後，初步分析了內螺紋管的優化設計問題，提出了一些建議。Analyzing of the heat transfer in microchannel heat sinks, finite element method is used to calculate the surface temperature, fluid temperature and the total thermal resistance of microchannel heat sinks with arbitrary base heat flux distribution
在對微管道散熱器進行傳熱分析時，本文利用有限元法在微管道底壁熱量任意分佈的情況下，計算了微管道的壁面溫度和流體溫度分佈，最終得到了總熱阻值。Flexible insulating sleeving - part 3 : specifications for individual types of sleeving - sheet 246 : heat - shrinkable polyolefin sleeving, dual wall, not flame retarded
絕緣軟套管.第3部分:各種類型套管的規范.第246活頁:不阻燃的雙壁熱收縮聚烯烴套管分享友人