管軸套 的英文怎麼說

中文拼音 [guǎnzhóutào]
管軸套 英文
sleeve
  • 管 : Ⅰ名詞1 （管子） pipe; tube 2 （吹奏的樂器） wind musical instrument 3 （形狀似管的電器件） valve;...
  • 軸 : 軸Ⅰ名詞1. （圓柱形的零件） axle; shaft 2. （對稱部分的直線） axis 3. （圓柱形的纏繞器物） roller; spool Ⅱ量詞（用於纏在軸上的線以及裝裱帶軸子的字畫）
  • 套 : 名1 （套子） cover; case; sheath 2 （河流或山勢的彎曲處） a bend of a river or a curve in a mount...
  1. Non - soldering and soldering compression couplings - tapped holes for socket unions - construction sheet

    非釬焊和釬焊壓緊聯軸節.套管接頭用螺紋孔.建造單
  2. When flux appears liquid and transparent on both tube and valve, start sweeping flame back and forth along axis of joint to maintain heat on parts to be joined, especially toward base of valve socket

    當焊劑變成液態並且在管道和閥門上呈現半透明狀態時，開始將火焰沿著連接部件的軸線進行進退烘烤，以保持連接部件、特別是閥門套筒底座部位的熱度。
  3. Sleeve type half bearings for automobile engines

    汽車發動機用套管型半軸承
  4. This research was also supposed to provide a valuable reference for the construction of 500kv eastern hangzhou transformer substation project. to guarantee the rationality of the torsion and bending load application, a set of experimental equipments was transformed from a traditional one by exerting tangential force on the brim of the fan board and conducting broad - billed roller application. in the actually fulfilled experiments on the capabilities of the members under different ratios of torsion and bending, the equipments proved to be well qualified in load applying to large - tonnage members

    試驗中，為保證扭轉及彎矩荷載施加的合理性，在浙江大學工程結構試驗室原有的加載設備的基礎上，分別採用在扇形板邊緣施加切向力和寬軸承滾軸加載的方法，改造並調試出一套可專門用於大噸位構件施加扭轉荷載及組合作用的試驗設備，並利用這套設備進行了離心鋼管混凝土構件在不同彎扭比的組合作用下的試驗研究。
  5. For a long period, we have supplied fittings to the first motors wuxi diesel engines factory, the first engine works of china first tractor, kunming yunnan lnternal - combustion engines factory, sichuan emei diesei engines factory, chongqing diesel engines factory, chongqing cummins factory, mianyang xincheng factory, nanchong lnternal - combustion engines factory, 420 company, guangxi liufa engines factory, guangxi yulin diesel engines factory, tianjin perkins, nanchong biaoma gears co., ltd. chongqing jiaka factory and chongqing dajiang factory etc. and maintenance markets inside or outside the province

    公司產品長期配套一汽錫柴一拖昆明雲內成都雲內川峨柴重柴重慶康明斯綿陽新晨南充內燃機廠420公司廣西柳發玉柴天津珀金斯南充彪馬重慶嘉卡重慶大江等省內外主機廠及維修市場，是中國最大的內燃機氣門座氣門搖臂搖臂軸氣門導管生產基地。
  6. Non - soldering and soldering compression couplings - socket unions

    非釬焊和釬焊壓緊聯軸節.套管接頭
  7. Inspection push - up load for fore and aft stern tube bushes

    艉軸管前、后襯套壓入檢查。
  8. Measuring diameter of fore and aft stern tube bearing and bushes

    艉軸管前、后軸承與襯套直徑測量。
  9. At an early stage in the evolution of the high - speed diesel a variable timing device was introduced in the pump drive coupling, taking the form of a helically splined coupling by means of which the angular relation between driving and driven shafts could be varied by manual or automatic control

    翻譯：在高速柴油機發展的早期，可變的正時裝置被引用到油泵驅動聯軸節上，採用螺旋式花鍵套管的形狀，驅動軸和從動軸之間的相對角度可以通過手動或自動控制進行改變。
  10. Hot - extrusion technology of the axle housing of the heavy truck and die design

    重型車半軸套管熱擠壓工藝及模具
  11. When in position, square with the pipe axis, it is clamped in place by hydraulically - operated shoes

    到位后，使其與管軸垂直，用液壓操縱套接在適當的位置處將其夾緊。
  12. Hydraulic grease fitting : hydraulic grease fitting provides for lubrication of yoke sleeve bearing surfaces ( not shown )

    液壓潤滑油注入器：液壓潤滑油注入器為軛架套管軸承表面提供潤滑（沒有圖示） 。
  13. Through the combination of analysis and experiments, we get a certain sense of the function of net cover. setting the research of axis ei as example, this paper studies the effect of net cover

    通過計算分析與試驗相結合，以金屬軟管軸向剛度的研究為例，研究了網套的作用，對金屬軟管網套的作用有了一定的認識。
  14. Flexible shaft sleeve of electric tools

    電動工具用軟軸套管
  15. Parameter determination of three - roller cross - rolling half - shaft casing

    半軸套管三輥滾縮成形工藝參數的確定
  16. This article analyzes some regulations for safety steering column, discusses the distribution of crashing energy and the structures and the safety control principls with flex steering shaft, breaking steering shaft, sleeve steering pillar tube as well as ripples tube steering pillar tube

    摘要分析了安全轉向柱的法規要求，汽車碰撞能量的分配，伸縮式轉向軸、可斷開式轉向軸、套筒式轉向柱管、波紋管式轉向柱管等的結構和安全控制原理。
  17. To adjust : when diaphragm is above the line, turn adjusting collar from left to right to increase the reduced pressure - opposite to decrease reduced pressure

    調節：如果隔膜位於管道上方，則從左向右旋轉調節軸套以增加減壓-相反，減少減壓。
  18. Mechanical tube, automobile semi - axle sleeve tube

    結構用管汽車半軸套管
  19. When diaphragm is below the line, turn adjusting collar from right to left to increase the reduced pressure - opposite to decrease the reduced pressure

    當隔膜位於管道下方，則從右到左旋轉調節軸套增加減壓-相反就是減少減壓。
  20. When diaphragm is below the horizontal line, turn adjusting collar from right to left to increase the reduced pressure - opposite to decrease the reduced pressure

    當隔膜位於水平管道下方，則從右到左旋轉調節軸套增加減壓-相反就是減少減壓。
分享友人
分享到 Line

分享到臉書