節后器 的英文怎麼說

The afterheat, which is collected by recovery devices, in winter can be used as the low level thermal source of heat pump, and in summer can preheat feed water, thus equivalent an economizer. because energy flows in the system so reasonably that energy is used to the most, therefore, its energy conservation effect is significant, and the operating expenditure declines consequently. the sewage can be reused after due treatment, thua it has a certain social and ecological benefit, too

本研究中選用分離式熱管裝置提供洗浴用水，利用水源熱泵裝置，一機兩用，進行空間供熱和製冷，並通過余熱回收器對系統內的余熱進行回收，冬季可作為水源熱泵的低位熱源，夏季可對鍋爐給水進行預熱，起到「省煤器」的作用。這樣實現系統內的能量合理流動，從而達到節能的目的，同時洗浴污水經適當的處理后可以回用，因而還具有一定的社會和生態效益。

The new chainset is a certain hit among gram watchers and details like the retaining circlips on the rear derailleur pulley wheel bolts are definitely positive, though they ' ll be even more so when they trickle down to more affordable rear derailleurs, a component many of us feel has to be treated as expendable

新的大飛組件對于那些對重量吹毛求疵的人來說是個打擊，一些細節，比如后撥鏈器擺臂滑輪軸的卡環，是十分有效的改進，盡管這樣的特性將在將來的低端產品中體現，但對大多數人來說，這些零件仍是昂貴的消耗品。

A circuit topology of the inverter with duty cycle extended active clamp forward style high frequency pulse dc link is adopted by each independent inverter. each inverter is cascaded by a circuit with duty cycle extended active clamp forward style high frequency pulse dc link and a dc / ac inverting bridge. the control strategy of voltage mode pwm forwardback is adopted by the former, and the control strategy of three - state discrete pulse modulation ( dpm ) hystersis current is adopted by the later

每個獨立的航空靜止變流器採用占空比擴展有源箝位正激式高頻脈沖直流環節電路拓撲，由占空比擴展有源箝位正激式高頻脈沖直流環節電路與dc ac逆變橋級聯而成，前級採用電壓型pwm前饋控制技術，后級採用三態dpm電流滯環控制技術。

Carry out operation of lasting effect birth control ; 2 place or take out an intrauterine device ; 3 it is to accord with country and province family planning regulation, after carrying out operation of lasting effect birth control, carry out again answer those who open an operation ; 4 it is break down is gravid, but disobey country and province family planning regulation does not have the except with gravid break down of warrant proper motion

一是實施長效節育手術的；二是放置或者取出宮內節育器的；三是符合國家和省計劃生育規定，實施長效節育手術后，又實施復通手術的；四是中止妊娠的，但違反國家和省計劃生育規定無正當理由自行中止妊娠的除外。

Supervisor point is behind the postposition of power amplifier, optic signals coming from a tap of 99 : 1 enter into optic spectrum scan module, then the power levels which have been calculated by iterative algorithmic are sent to power control module to guide a set of tunable electronic attenuators

此方案將監測點放在後置功率放大器的後面，從分束器中分出99 ： 1的光進入光頻譜掃描模塊，傳給功率控制模塊的光功率值經過選代演算法后計算出均衡后的功率值送到功率控制模塊的控制中心去調節電可調節衰減器。

The operation principleresult of saving power ， mate rial and reliability of ac and dc usual auto - converting saving power instrument are expounded, which the operation - coil of ac contactor given ac and dc voltage is usual, output is even dc, on and off and keeping voltage non - contactor auto - convert

論述了與交流接觸器操作線圈適配的交直流輸入（操作）電壓通用、恆直流輸出、吸合與保持電壓無觸點自動轉換節電器的工作原理；接觸器配用節電器后的節能節材效果及節電器的可靠性。

The control system of mould level is crucial to improve the slab quality in the continuous casting process, pid controller is used in the traditional mould level control, and it has some defaults, such as : at the start - up or finishing period of casting or during the changeover of tundish, pid control has a bad effect, its overshoot is large and its transient time is long ; the erosion of the tundish stopper and the submersed nozzles lead to the accuracy of control become bad ; the abrupt falloff of block in the submersed nozzles makes the level acutely fluctuate, and pid control can not overcome the disturbances resulted from the change of casting speed

結晶器液位控制系統是提高連鑄產品質量的關鍵環節，傳統的連鑄機液位控制方法採用常規的pid控制，存在如下不足：開始、結束澆注和換中間罐澆注時，控制效果差，超調量大，過渡時間長；塞棒頭和浸入式水口被腐蝕后引起控制精度差；浸入式水口堵塞物的突然脫落所引起的液位劇烈波動；無法克服拉速波動引起的擾動。

During the period of measurement, the transduction circuits transform the differential pressures, the absolute pressures and the temperatures received by the sensors into the voltage signals, and then, the voltage signals are transformed into digital signals by the a / d convertor. the mcu processes these digital signals and calculates the cumulation of the flow. finally the totalizers contact with the pc by rs - 485 bus to form a distributed measuring network

在測量過程中，系統以流量計節流所獲得的差壓信號作為主信號、絕壓和溫度信號作為補償信號進行流量積算，這三種信號分別由相應傳感器感知后，經各自的物理信號測量電路轉換為電信號，再由a / d轉換模塊轉變為數字量，交微控制器進行處理、積算。

3, on the base of the traditional spatial filtering, the author present, a new despeckle algorithm, that make use of iterated processing and correlated neighbourhood model, iterated filtering method of the sar image combining the correlated neighbourhood model with maximum a posteriori filter. first, a series of templates refecting direction information are established and every template is present for a kind of neighbour structure. then on the basis of sar images statistical property, the maximum a posteriori estimate of the real intensity under observation image values is got by bayes formulatio - n

3 、針對傳統空間濾波器的不足，引入迭代處理和相關鄰域模型的概念，提出了基於相關鄰域模型的最大后驗迭代濾波。該演算法引用一系列反映局部邊界特徵的鄰域模型，以描述圖像的細節。引入強度的先驗概率分佈模型，利用bayes方法，對各個結構進行實際強度的最大后驗估計。

Effects of different calcium concentration on ca2 + in ca2 * - sequester ing organelles of photoreceptor cell in penaeus monodon fabriciu by the combined oxalate - pyroantimonate technique, we observed the subcellular distribution of calcium in the photoreceptor cells of penaeus monodon fabricius, by changing the extracellular calcium concentration. the result showed that, in vitro, in presence of 50mmol / l, the quantity of calcium antimonate deposit in the multivesicular bodies, pigment and lamellar body were more than that of photoreceptor incubated in lower calcium solution, which contained 50mmol / l egta. in higher calcium solution, we ecu id not f i nd the depos i t in the mitochondr ia, but in lower calcium solution, there was a little deposit in the mitochondria

學位論義小同ca卜濃度對斑節對蝦光感受器的形響3 .外界不同鈣離子濃度對斑節對蝦光感受器細胞內所儲存的鈣離子的影響應用草酸一焦銻酸鹽結合的沉澱技術研究斑節對蝦光感受器細胞在不同ca之『濃度條件下胞內儲存的ca2 +變化，其電鏡觀察表明:在高鈣溶液培育后，細胞內的多囊體、色素顆粒、板膜體中都存在大量的焦銻酸鈣沉澱的黑色顆粒，線粒體中未發現沉澱;在生理溶液培育后，線粒體中出現沉澱，而其他caz +儲存器中焦銻酸鈣沉澱的黑色顆粒大量減少。

In this report, we mainly covered the following aspects of " tissue organ regeneration and replication in situ " : 1 ) procedures of tissue organd regeneration and replication and replication in clnical practice ; 2 ) the discover and existence of potentiald regenerative cell ( prc ) ; 3 ) the proliferation, differentiation and regeneration law of potential law of potential regenerative cells ; 4 ) study procedure on tissue organ regeneration and replication from prcs in vitro based on the model of full skin organ regeneration in situ after extensive in vitro, set up the method and technology of searching life regenerative substance required in tissue organ regeneration and replication in situ. in this study, first, the whole human body is divided into 206 function units, which are the " tissue organ " in regeneration study. then the histology foundation of tissue organ regeneration and replication in situ is set up. in ordre to prove the existence of the potential regenerative cells and their potential baility and function, we established clinical tracking rechnique of skin organ regeneration in situ ; meanwhile, several tissue organ regeneration and replication in vitro models which represent different kinds of runctions were sucessfully set up, with all these techniques and models, we confirmed : 1 ) the existence, function and ability of pptemtoa regenerative cells ; 2 ) the importance of life regenerative substance ; 3 ) the feasibility of tissue organ regeneration and replication in situ ; 4 ) the big value of tissue organ regeneration and replication in situ in life science and medicine progerss. we also showed the possible foreground of capture cancer with this method and technologh. in this report, nearly 200 photographs of several tissue organ regeneration and replication in situ or in vitro demonstrated the whole process of tissue organ and big organ entities regeneration and replication from cells. the results of tissue organ regeneration and replication in situ mainly include : 1 ) whole skin organ regeneration and replication in situ ; 2 ) gastrointestinal mucosa tissue organ regeneration in vitro ; 3 ) hair follicle tissue organ regeneration in situ or in vitro ; 4 ) never tissue organ regeneration in situ ; 5 ) pancreas tissue organ regeneration and replication in vitro ; 5 ) marrow tissue regeneration in vitro ; 6 ) renal glomerulus and tubule tissue organ tugeneraation in vitro ; 7 ) heart muscle regeneration in vitro, etcl. in order to let more and more people know and understand this technology of tissue organd regeneration and replication in situ, herein, for the first time, we publicize the key points of actualizing this technology. also, we publicized the technology procedures and the frame constitute of life substances. we bilieve this is a big contribution to human science

本研究報告，重點報道了組織器官的原位再生復制的臨床程序，報道了組織潛能再生細胞的發現和存在，以及該細胞的增殖分化和形成組織器官的變化規律.以燒傷后皮膚組織器官的原位再生復制為模型，研究出了體外組織潛能再生細胞復制組織器官的培養方法;以體外組織器官的復制為模型，建立了尋找原位組織器官再生復制所需生命物質的方法和技術.本研究，首先按人體的器官功能，分解為206個功能單位，確立了所復制的人體器官中的組織功能單位為組織器官，從而建立了原位組織器官再生復制的組織學基礎.為了驗證組織潛能再生細胞的再生潛能，建立了皮膚器官原位再生的實體臨床跟蹤技術，同時又建立了能代表有關器官功能類別的代表組織器官的原位和體外復制模型，以多組織器官的成功復制確定潛能再生細胞的作用，確定生命研究再生物質的重要性，確定組織器官原位再生復制的可行性，確定了組織器官原位再生復制的生命科學研究和醫學進步的重大應用價值，同時展示了用此方法和技術攻克癌癥的前景.本研究報告，以近二百幅多個組織器官原位和體外再生復制的實體圖片，展示了潛能再生細胞復制的組織器官和大器官司實體;展示了細胞再生復制器官的全過程.真實的報告了組織器官原位再生復制的成果.所公布的主要成果為:皮膚器官的原位再生復制;胃腸黏膜組織器官的原位和體外再生復制;毛囊組織器官的原位和體外再生復制;神經組織器官的原位復制;胰腺組織器官的體外復制;骨髓組織的體外復制;腎小球小管組織器官的體外復制;心肌的體外復制等.為了讓更多的人學會和掌握組織器官原位再生復制技術，本報告首次公布實施技術的重要環節和技術流程;首次公布了生命再生物質的框架和組成.作者自費研究成果對人類生命科學的一大貢獻

The improvement system is made up of the pressure sensor, flow sensor, displacement sensor, electro - hydraulic proportional flow control valve, power amplifier, data gathering board and computer. the platform can carry out testing the hydraulic parameters, processing the tested data, saving the processed data and drawing, adjusting the pressure automatically

改造后的測控系統主要由壓力傳感器、流量傳感器、位移傳感器、比例節流閥、功率放大器、數據採集卡和計算機組成。改造后的實驗臺具有自動採集實驗數據、自動處理實驗數據、自動保存實驗數據、自動調節液壓系統負載壓力等功能，大大提高了實驗臺的工作效率、測試精度和智能化水平。

3. with comprehensive improvement of transponder including structural adjustment to lna ; optimization of ( phase locked loop ) pll filter ; structural adjustment to the transmitter and phase error adjustment to the intermediate frequency demodulation circuit, we have successfully enhanced sensitivity, expanded dynamic range, increased transmitting power and improved the spectrum purity ; decreased capture time for pll ; improved the signal quality after demodulation ; reduced its volume and power consumption. 4

3 、對通信機的全面改進，包括lna結構的調整、鎖相環環路濾波器的優化、發射部分結構的調整以及中頻解調電路的相差調整，提高了系統的接收靈敏度、改善了本振的頻譜純度、減少了鎖相環的鎖定時間、使中頻解調后的信號質量大為提高，同時還減少了體積、節約了系統的功耗。

The effect of economizing energy and materials after the contactor adapts the electro - ecomonizer and its reliability is useful to the research on operating - control and economizing electricity of other electromagnets

接觸器配用節電器后的節能、節材效果顯著，節電器工作可靠，可供其他電磁鐵的操作控制及節電研究參考，具有一定的實用價值。

A memorial rearview mirror and chair control rout is studied, which can adjust, memorize and resume the position of rearview mirror and chair

摘要研究了一種能電動調節后視鏡和座椅位置，並能記憶存儲和調用位置信息的記憶存儲式后視鏡和座椅控制器。

These variable geometry components include high pressure - compressor, high - pressure turbine, low - pressure turbine, inlet area ratio of mixer and main nozzle throat area. the results of calculation show that the adjusting of low - pressure turbine and mixer has a remarkable effect on the performance of engine and bypass ratio

計算結果表明，低壓渦輪和混合器的調節對發動機的性能和涵道比的影響尤為顯著；在其它部件幾何結構不同時，單個部件幾何調節后，發動機性能的變化趨勢是不同的。

The system can simulate the transfer process of photo - thermal and thermal - electric at a given parameter setting of structure, environment and circuit. on the basis of circuit structure, the calibration, parameter adjusting and signal readout can be simulated, the vary process of readout circuit, readout voltage, optical gain, optical gain rate, and uniformity can be given. in addition, all kinds of character parameters of device can be forecasted

本論文根據umbirfpa的原理，建立它的軟體模擬系統，它可以根據給定的結構、環境、電路設置等參數首先模擬光熱、熱電轉換過程，並可根據電路結構，模擬校準、參數調節並讀出信號，給出讀出電流和電壓、光學增益、光學增益比、非均勻性等各特徵量的定量變化過程，預測製成后器件的各種性能參數。

A clinical observation of removal of iud for postmenopausal women

絕經后婦女摘取宮內節育器的臨床觀察

Provides protocol support and other features ( see the appropriate list, later in this section ) whether or not domain controller upgrades and the organizing of active directory structures have been carried out

不論域控制器是否升級和是否已經組織了activedirectory的結構，就提供協議支持和其他功能（參閱本節后的相應列表） ，

The buttonholes programmed by the operator are sewn sequentially ; the respective cutting length is allocated fully automatically. this means maximum efficiency, even for short runs

因此，在完成一種鎖眼后無需做其他的調節，機器根據操作人員編制好的程序序列，自動地改變切孔長度進行鎖眼，極大程度地提高了生產效率。