簡單對稱軸 的英文怎麼說
中文拼音 [jiǎndānduìchènzhóu]
簡單對稱軸
英文
simple axis of symmetry- 簡 : Ⅰ形容詞（簡單） simple; simplified; brief Ⅱ動詞1 （使簡單; 簡化） simplify 2 [書面語] （選擇人才...
- 對 : Ⅰ動詞1 （回答） answer; reply 2 （對待; 對付） treat; cope with; counter 3 （朝; 向; 面對） be tr...
- 稱 : 稱動詞（適合; 相當） fit; match; suit
- 軸 : 軸Ⅰ名詞1. （圓柱形的零件） axle; shaft 2. （對稱部分的直線） axis 3. （圓柱形的纏繞器物） roller; spool Ⅱ量詞（用於纏在軸上的線以及裝裱帶軸子的字畫）
- 簡單 : 1 （不復雜） simple; uncomplicated; plain; simplicity 2 （平凡 多用否定式） commonplace; ordinary...
-
Moke and fmr studies were performed on single crystalline fe ultathin films epitaxially grown on iii - v semiconductor gaas substrate with thickness 4. 1 - 33 monolayer ( ml ). a theoretical mode for fitting fmr experimental data was established. the results demonstrated the structures and reproduced the evolution of the magnetic properties of ultrathin films with various thickness from the state of superparamagnetic nano - cluster through coexistence of two magnetic phases to continuous film, especially the change of magnetic crystalline anisotropy from unixial to cubic
1 - 33原子層厚度（ monolayer ，簡稱ml ）的fe單晶超薄膜進行了鐵磁共振（ fmr ）和磁光研究，建立了理論模型對鐵磁共振實驗結果進行了模擬，重現了不同厚度的超薄膜，從納米團簇到兩相共存的過度階段直至連續薄膜結構與磁性的變化，特別是磁各向異性從單軸各向異性向立方各向異性轉變的演化過程。In order to make the sensitivity of 2 - demension accelerometer along the two main arbors almost identical, symmetric four - beam structure that embeds a double - sides interdigitated differential capacitive with puckered beam in two directions was used as sensitive component. in addition, the differential capacitive accelerometer fabricated by bulky silicon micromechanical technique has high sensitivity, wide measurement scope, less nonlinear error, and simple converting circuit. then, the structure parameters of the sensitive component were calculated and stimulated, which results in a set of the optimized structure design parameters, main fabrication procedure and several key fabrication technology
為使二維振動傳感器在兩主軸方向的靈敏度大致相同，敏感元件採用高度對稱的四梁結構，其中每個軸向上均採用帶折疊梁的雙側叉指電容結構，採用體硅微機械工藝製作的高深寬比叉指電容式敏感元件，具有高靈敏度、寬量程、非線性誤差小、外圍電路簡單等優點;對設計的敏感元件結構參數進行了計算，並利用有限元法進行了模擬分析，根據模擬結果得出了優化參數;在確定敏感結構的基礎上，研究了敏感元件採用體硅微機械加工工藝製作的工藝流程和關鍵工藝技術;對敏感晶元內部的c - v介面電路進行了原理設計與分析，利用差動測量技術得到由振動引起的微小電容變化量，經c - v介面電路進行相位調制處理，然後通過解調輸出與加速度成正比的電壓信號。Abstract : approximate methods for calculating aerodynamic heating rates on space shuttles are discussed. various methods are given for predicting the heating rate at axisymmetric stagnation points, general three dimensional stagnationpoints and the leading edge stagnation point of wings. numerous laminar and turbulent heating techniques for flat plates and cones are analyzed and compared. a brief review of some methods is presented to predict heating rate for winward centerline and lateral direction off the symmetry plane. the results show that the methods are simpler and can guarantee enought precision for predicting aerodynamic heating environment of space shuttles
文摘:介紹了國內外預測航天飛機氣動加熱的工程計算方法.給出了軸對稱、非軸對稱和機翼前緣等各種外形駐點熱流密度的計算，分析和比較了平板、錐體的層流和湍流熱流密度計算的各種方法，概述了航天飛機迎風面中心線和離開中心線橫向熱流密度的計算.計算結果表明，本文方法用在航天飛機氣動熱環境初步設計中比較簡單並且有足夠精度Cylindrical cup is a typical axial symmetrical part, though the deformation of material is simple in drawing process, but during the drawing process, exists a lot of influence factors ( including workpiece material character itself as well as each technological parameters ), and they restrict mutually between the factors. so how to calculate the limiting drawing rate of a cup becomes a complicated nonlinear and multi - gene question. to predicting limiting drawing rate of the cylindrical cup accurately indeed is a very complex subject
筒形件是典型的軸對稱拉深件，在拉深過程中材料的變形雖然相對簡單，但是在生產過程中，由於影響因素很多（包括工件材料本身性能以及各個工藝參數） ，且各種因素之間相互制約，故如何準確地計算筒形件拉深極限就成為一個復雜的非線性多因子問題，要真正準確預測筒形件極限拉深系數也是一個非常復雜的課題。Simplified theories are also presented for curved beams with commonly used sections, such as i - shape, channel and h section without any symmetrical axis. linear analysis is also performed in combination with finite element method
其後就常見的截面形式（單軸對稱工字形、槽形和無對稱軸的形截面） ，對所提出的曲梁理論進行簡化，並結合有限元方法求解曲梁的線性問題。分享友人