粗粒鋼 的英文怎麼說
中文拼音 [cūlìgāng]
粗粒鋼
英文
coarse grain steel-
Effect of microalloy element on the grain coarsening behavior of q345 steel
345鋼奧氏體晶粒粗化行為的影響Main products : crusher, crushing machine, fine crushing machine, centrifugal screen, tyre wire puller, cutter, rubber stripping machine, cut - off machine, magnetic separation conveyor and steel wire dicing cutter
主要產品有:破碎機、粗碎機、細粉碎機組、離心篩;輪胎拔絲機、切割機、剝膠機、切斷機;磁選輸送機、鋼絲切粒機(生產鋼丸)等。The experimental results show that there are few differences in the mechanical properties between normal concrete slabs and lightweight aggregate concrete slabs which are made by haydite as coarse aggregate. at the same time, the haydite concrete proved that it is available in practice
試驗研究結果說明,以南寧市福民節能保溫陶粒製品廠生產的陶粒作粗骨料的輕質混凝土板,其受力性能與普通鋼筋混凝土板沒有什麼差別,可以用於工程實際。Effect of percent reduction and alloying elements on the austenite grain coarsening temperature of 18crmnbhz steel
鋼奧氏體晶粒粗化溫度的影響Influence of ti content on austenite grain size and grain coarsening temperature in medium - carbon boron steel
鈦含量對中碳硼鋼奧氏體晶粒度及晶粒粗化溫度的影響The effect of reheating austenitizing temperature on grain coarsening, the dissolution of vanadium compound and hardness of 50mn2v steel
鋼再加熱奧氏體化溫度對晶粒粗化釩化物溶解及硬度的影響Grain size simulation of 45 steel forging during upsetting
鋼鍛件熱鐓粗過程晶粒尺寸模擬These balls are made in a shorter process so the cost is significantly lower than round balls. for larger grain grinding or where roundness is not important, short headed balls are an excellent alternative choice. these balls have a flat area on both poles and they also have three different finishes
打頭珠都沒有經過圓磨製程,因此成本比圓珠低很多,對于較粗糙粒度的研磨或使用6mm以上尺寸的研磨鋼珠都可以考慮使用打頭珠,不但可以達到與圓珠相差不多的研磨效果,卻可以節省大量耗材成本。The results indicate that the surface grain size of the steel sheets is smaller than that of the center by batch annealing, while it is on the contrary of the steel sheets by continuous annealing
結果表明,罩式退火后鋼板表面晶粒比心部的細小,而連續退火后鋼板表面晶粒比心部的粗。On the condition of the test, the cutting force of ticp / fe composites was more than which of 45 steel by 60n, and the cutting temperature was higher than which of 45 # steel by 90, and the roughness of machined surface was almost as much as which of 45 # steel. tic ceramic particles enhanced the cutting force and the cutting temperature of ticp / fe composites, but had little effect on the roughness of machined surface. the machining quality of ticp / fe in situ composite was similarity to 45 # steel
在本試驗條件下,原位tic _ p fe復合材料切削加工時的切削力與45 ~ #鋼相比要大60n ,切削溫度要高90 ,加工表面粗糙度與45 ~ #鋼相近; tic陶瓷顆粒使原位tic _ p fe復合材料切削加工時的切削力增大、切削溫度增高,對加工表面粗糙度影響不大;原位tic _ p fe復合材料的可加工性與45 ~ #鋼相當。Coarse - grained steel
粗晶粒鋼分享友人