粘接位置 的英文怎麼說
中文拼音 [niánjiēwèizhì]
粘接位置
英文
klebstelle bonding surface- 粘 : 粘動詞（粘附） glue; stick; paste; adhere to; bond
- 接 : Ⅰ動詞1 （靠近;接觸） come into contact with; come close to 2 （連接; 使連接） connect; join; put ...
- 位 : Ⅰ名詞1 （所在或所佔的地方） place; location 2 （職位; 地位） position; post; status 3 （特指皇帝...
- 置 : 動詞1. （擱; 放） place; put; lay 2. （設立; 布置） set up; establish; arrange; fix up 3. （購置） buy; purchase
-
According to the special shape and operate requirements of the torpedo, the structure and moulding process of the torpedo shell are established, in which the body and overlay block with grooves are moulded by fiber winding, and close moulding respectively with the adhesive by limited stop compression. in the light of the selection of raw material system, composite system with outstanding performance are defined, based on which the mechanical properties are tested., with the overall consideration of structural characters and design demands, the main factors which may have effects on the strength and stability ( including stiffness section dimension, stiffeners space, skin thickness and skin lay angle ) is optimized one by one for the structure design parameters on the base of the fem model of skin, stiffness and layover block by fem. as a result, the prototype with 1 : 1 proportion and its structure and lay optimization design are completed. the moulding technology for polyurethane foam moulding the stiffened shell is obtai ned in terms of the design, manufacture moulding, experimental mould and tooling
依據在研產品特殊的外型結構和使用要求，確定了該型號水雷復合材料殼體的具體結構形式和復合成型工藝路線，即由纖維纏繞工藝成型主體異形件，閉模成型帶通槽外貼塊，用限位加壓工裝實現粘接的工藝路線；通過對原材料體系的篩選，確定了綜合性能較好的復合材料體系，以此為基礎進行了力學性能測試；運用有限元方法，建立了蒙皮、筋條和外貼塊的分析模型，綜合考慮結構特點和設計要求，對影響結構強度與穩定性的主要因素（包括筋截面尺寸、筋間距、蒙皮厚度、蒙皮鋪層角度）分別進行了結構設計參數的優選，最終完成了復合材料異形耐外壓殼體1 : 1樣件和縮比實驗件結構及鋪層優化設計；完成了聚氨酯泡沫胎成型內置加筋殼體的成型工藝技術研究；對縮比件進行外壓性能測試，並給出了應力、應變測試結果。Shear properties in the plane of the panel ( interlaminar shear ) duplicate the kind of shear stress encountered in such glued structural assemblies as structural sandwiches and adjacent to gluelines between flanges and webs in box - beams and i - beams and gusset plates in trusses
面板平面的剪切特性（層間剪切） ，與夾層結構這類粘合組件，以及箱形梁、工字梁凸緣與腹板間的焊接層和桁架加固板附近位置所受的剪切應力類型相同。While the chips are attached to near center or near a edge of subatrate, the mean, deviation and maximum are at the almost same level ; when the chip is attached near a corner, the deviation and the maximum is far larger than those of the above two positions ; during thermal treatment followed, the residual stress demonstrates a regular cycle trend when the chips are attached near center or edge of the substrate and fluctuates in a wide range when the chip is attached near a corner
當晶元粘貼在基板中心和靠近基板邊緣的位置時粘合劑固化后殘余應力的平均值、最大值和數值的分散性皆處于相接近的水平，而當粘貼在基板靠近一角的位置時應力分佈狀況則有很大不同：應力的分散性增大，應力最大值也遠大於粘貼于另外兩個位置時的值。
分享友人