粘貼式應變計 的英文怎麼說
中文拼音 [niántiēshìyīngbiànjì]
粘貼式應變計
英文
bended strain gage- 粘 : 粘動詞（粘附） glue; stick; paste; adhere to; bond
- 貼 : Ⅰ動詞1 （粘貼） stick; paste; glue 2 （緊挨） nestle up to; snuggle up to 3 （貼補） subsidize; h...
- 式 : 名詞1 （樣式） type; style 2 （格式） pattern; form 3 （儀式; 典禮） ceremony; ritual 4 （自然科...
- 應 : 應動詞1 （回答） answer; respond to; echo 2 （滿足要求） comply with; grant 3 （順應; 適應） suit...
- 計 : Ⅰ動詞1 （計算） count; compute; calculate; number 2 （設想; 打算） plan; plot Ⅱ名詞1 （測量或計算...
- 粘貼 : paste; stick
-
Bonded strain gage
粘貼式應變計According to the special shape and operate requirements of the torpedo, the structure and moulding process of the torpedo shell are established, in which the body and overlay block with grooves are moulded by fiber winding, and close moulding respectively with the adhesive by limited stop compression. in the light of the selection of raw material system, composite system with outstanding performance are defined, based on which the mechanical properties are tested., with the overall consideration of structural characters and design demands, the main factors which may have effects on the strength and stability ( including stiffness section dimension, stiffeners space, skin thickness and skin lay angle ) is optimized one by one for the structure design parameters on the base of the fem model of skin, stiffness and layover block by fem. as a result, the prototype with 1 : 1 proportion and its structure and lay optimization design are completed. the moulding technology for polyurethane foam moulding the stiffened shell is obtai ned in terms of the design, manufacture moulding, experimental mould and tooling
依據在研產品特殊的外型結構和使用要求，確定了該型號水雷復合材料殼體的具體結構形式和復合成型工藝路線，即由纖維纏繞工藝成型主體異形件，閉模成型帶通槽外貼塊，用限位加壓工裝實現粘接的工藝路線；通過對原材料體系的篩選，確定了綜合性能較好的復合材料體系，以此為基礎進行了力學性能測試；運用有限元方法，建立了蒙皮、筋條和外貼塊的分析模型，綜合考慮結構特點和設計要求，對影響結構強度與穩定性的主要因素（包括筋截面尺寸、筋間距、蒙皮厚度、蒙皮鋪層角度）分別進行了結構設計參數的優選，最終完成了復合材料異形耐外壓殼體1 : 1樣件和縮比實驗件結構及鋪層優化設計；完成了聚氨酯泡沫胎成型內置加筋殼體的成型工藝技術研究；對縮比件進行外壓性能測試，並給出了應力、應變測試結果。Through the bonding tests and the theory analysis between the advanced composite glass sheets and the concrete under the general load - carrying condition, the iterative load - carrying condition, the freeze - thaw action, and the defective bonding, the calculative model has been established, and the numerical value of fibre sheet strain under different load - carrying has been confirmed. the bond strength calculative expressions for the concrete bonded with glass fibre sheet under the pull - shear and the bend load - carrying conditions have been established. the author put forward the decreasing coefficient and the calculative expressions for the influence of reinforce effect by the non - effective area and the calculative expressions for the influence of the freeze - thaw action on the carrying capacity of the concrete beams
本文採用美國泰扶高強復合玻璃纖維布以及與之性能相當、由南京玻璃纖維研究院自行研製開發的egfw430型玻璃纖維布兩種材料，通過在靜載、重復荷載、凍融及有缺陷粘結條件下的高強玻璃纖維布與混凝土粘結性能的試驗研究與理論分析，建立了玻璃纖維布-混凝土的粘結計算模型，明確了不同受力狀態下纖維布應變的設計取值，提出了玻璃纖維布-混凝土抗剪粘結強度的計算公式;確定了考慮非有效粘貼面積對加固效果影響的折減系數;給出了凍融循環次數引起承載力下降的插值計算方法;並驗證了重復荷載作用下玻璃纖維布與混凝土良好的粘結性能。Bonded foiled gage
粘貼箔式應變計In order to simplify the calculated procedure, the error coefficient ( r1 ) has been introduced to paper. and so, the criterion formula ( 2. 1 ), which calculates strain and stress in concrete, can be replaced by one - variable formula ( 2. 17 )
為簡化計算類設計破壞形態時粘貼加固構件的抗彎承載力，本文引入誤差調整系數_ 1 ，將規范混凝土應力?應變公式（ 2 . 1 ）簡化成一階線性公式（ 2 . 17 ）並代入計算。Based on literature and introducing the error coefficient ( r2 ), the paper infers the formula ( 2. 63 - 2. 66 ), which is applied to calculate the lag strain of bonded materials ( elag ) under the secondary load
本文在有關文獻的基礎上，引入誤差調整系數_ 2 ，推導出鋼筋混凝土受彎構件二次受力下粘貼加固材料滯后應變_ （ tag ）的計算公式（ 2 . 63 ） （ 2 . 66 ） 。Unbonded strain gauge
非粘貼式應變計Honded strain gauge
粘貼式應變計分享友人