縮尺比 的英文怎麼說

中文拼音 [suōchǐbǐ]
縮尺比 英文
scale ratio
  • 縮 : 縮構詞成分。
  • 尺 : 尺名詞[音樂] （中國民族音樂音階上的一級 樂譜上用做記音符號 參看「工尺」） a note of the scale in ...
  • 比 : Ⅰ動詞1 （比較; 較量高下、 長短、距離、好壞等） compare; compete; contrast; match; emulate 2 （比...
  1. This paper deriving the theory work inflection point in the static stage characteristics curve of small measurement range linear dimension measurement. by the way of high pressure and back pressure pneumatic measure and designed the parameter of the mainly and measure spray head, which are the key component in the spray head - baffle pneumatic sensor. the different groups for the main - spray head and the measure spray head, will effect the dynamic and static stage characteristic parameter. the author have done contrast experiment and optimization design to test and verify the theory derivation whereby made the rang of show valve of pneumatic measure system measure range up to 40 u m, the sensitivity up to 100mv / u m, resolution up to 0. 05 p m, the uncertainly of measure is less than 0. o2 u m, satisfaction of requirement of groups the carboy hatch thickness size precise measure of soft shims

    對高壓背壓式氣動測量用於小量程線性尺寸測量的靜態特性曲線的理論工作拐點進行了推導，對氣動測量系統中的噴嘴-擋板型氣動傳感器中的關鍵部件? ?主噴嘴和測量噴嘴的參數進行了理論設計，對主噴嘴和測量噴嘴的不同組合，將影響測量系統靜、動態特性指標的噴嘴參數進行了對比實驗和優化設計，並通過實驗驗證了理論推導，從而使氣動測量系統量程的示值范圍達到40 m ，靈敏度達到100mv m ，解析度達到0 . 05 m ，測量不確定度小於0 . 2 m ，滿足了壓縮機缸蓋軟體墊片厚度尺寸精密測量分組的要求。
  2. An inductor whose case has been formed via a molding process, common molding processes in clu - de injection and transfer molding, molded inductors typically have well defined body dimensi - ons which consist of smooth surfaces and sharper coners as compared to othercase types such as epoxy coated and shrink wrap coatings ( also see inductor

    外殼以鑄型掉程所成形之電感，通常鑄型製程包括射出及轉移鑄型兩種，與其他型式之電感如環氧權脂包覆的電感及伸縮套管之電感比較起來，鑄型電感常有很明確的尺寸，平滑的表面及尖銳的邊角。
  3. A compressed horizontal scale commonly is helpful in seeing stratigraphic changes.

    縮小水平比例尺一般有助於觀察地層變化。
  4. Phenolic foam is a new generation heat preservation prevent fire soundproof material and polystyrene together ammonia ester foaming rubber etc, material to compare, and it is good that its biggest characteristics is a heat - proofound the low temperature contractility is smatt, and have te special prevent burning wit the size stability under 2000 heat, not burning, not melt not contract constant form not poisonous spirit hove no thick smoke, just surface formation layer

    信息內容：酚醛泡沫為新一代保溫防火隔音材料與聚苯乙烯聚氨脂發泡橡膠比，其最大特點是耐熱性好，低溫收縮性小，具有獨特的阻燃和尺寸穩定性，在焊槍火焰下，不燃燒不收縮不變形，無毒氣無濃煙，只是表面炭化，性質穩定，耐化學腐蝕抗老化。
  5. The following results were found, i. e., the water ratio affects obviously the acoustic wave velocity of rock sample ; the wave velocity is higher in saturated rock samples than in unsaturated ones ; and it decreases gradually with the strain of samples during uniaxial compression ; and also with the lengthening holding time at 160 ; when heating the samples the acoustic wave velocity increases slightly in initial stage and comes to the peak value at 60, then decreases gradually with increasing temperature ; meantime, there is a certain temperature effect on rock samples size

    實驗發現含水率對波速影響比較大，飽和巖樣的聲波傳播速度高於不飽和巖樣的聲波傳播速度；人工預制裂紋對聲波傳播速度影響不大；單軸壓縮條件下，聲波傳播速度隨應變增加逐漸降低；在同一溫度（ 160 ）下，波速隨保溫時間的增加而逐漸降低；在對巖樣逐漸加熱情況下，初始加熱階段波速略有升高，當溫度達到60時，巖樣波速達到峰值，之後隨著溫度繼續升高其波速逐漸下降；波速隨溫度變化具有一定的尺寸效應。
  6. The simulation results are compared to the normal dipole antenna in order to observe the influence of fractal and investigate the effect of antenna miniaturization. the relationship between miniaturization and fractal dimension is researched. the koch and 3 / 2curve fractal unit are applied to yagi - uda antenna, the performance like impedance characteristic and radiation pattern is simulated by cst microwave studio ?

    對其阻抗特性及輻射方向圖進行了模擬計算，並分別與未應用分形的普通半波振子天線相比較，觀察分形對天線性能的影響，以檢驗分形天線小型化的效果，研究了尺寸縮減性與其分形結構的分形維數之間的關系。
  7. Because the well reservation of the advantages of traditional large sacle advertising airboat, thoughtful design and argumentation on every level has been made, the dimension of the airboat reduced to 9 - 16 meters, adaptable area remarkably increased, flying agility obviously improved, a place as large as a playground is enough for it s taking off or landing, a space as size as a bus warehouse is sufficient to store the airboat, the advertising area of the airboat on it s two sides become less to 9 - 12 square meters, the altitude where such airboat can fly is much lower than that that drives person, presenting a little difference in views of the people on the ground, so capable to take the place of human - driving airboat, on the other hand when the size reduced, the operation, use, freight and maintenance become very easy, easy operation become it s first advantage : remote controllable, no professional driver needed, common personal can operate it after a short trainning, trainning time ranges from 3 - 5 days single, 15 - 30 days for people

    是因為它完美的保留和發展了大型載人廣告飛艇的優勢，為此我們進行了方方面面且深入細致的設計和論證，首先縮小了飛艇的尺寸， 9至16米長，大大的增加了飛艇的適用范圍，使飛行的靈活性得到了改善，學校操場大小的地方就可從容的起飛降落，大客車或大貨車的車庫便能存放，廣告面積雖然也小了，每單側9至12平米，可遙控飛艇的飛行高度也比載人艇的飛行高度低很多，以地面的視覺效果來看效果相差非常小，足以代替載人艇，其次是飛艇縮小后，整艇的操作使用運輸維護也都大大的簡化了，操作簡便是它的第一大優點：由於是遙控飛艇，就不需要專業的駕駛員來操作，普通人經過短期的技術培訓就可勝任，培訓期每單人為三至五天，多人視人數十五至三十天。
  8. The design of huge rate artillery model and madding methods were solved

    研究解決了火炮大比例縮尺模型的設計方法和製造手段。
  9. The research mainly includes the following respects : first, 1 / 10 scale reinforced concrete model has been preceded

    具體研究工作如下：首先，對卸煤溝原型進行了1 10縮尺比例的鋼筋混凝土結構模型試驗。
  10. So it is a double composite shear wall. experimental study and theoretic analysis on the seismic behavior of this new shear wall have been done in this paper. 2

    2 .進行了6個1 / 3縮尺的剪跨比為1 . 85的中高剪力墻的抗震性能試驗研究。
  11. Experimental study on the seismic behavior has been systemicly studied and theory analysis has been done to this new shear wall. the main contents are listed as follows : 1

    本文主要工作: 1 .進行了6個1 / 3縮尺的剪跨比為2 . 2的高剪力墻的抗震性能試驗研究。
  12. The data got from the shooting tests, conversed by the theory of similitude and eliminated the system errors, were compared with the data from the approval test in the national shooting field. it verified that the full parameters artillery physical simulation theory was right. it verified that the huge rate model design and madding methods were reliable

    把模型炮實驗獲得的數據，按相似理論換算，並消除相似畸變帶來的試驗誤差后，與原型炮在國家靶場定型試驗的結果比較，證明了創建的火炮全參數物理模擬理論的正確性；證明所採取的大比例縮尺模型的設計方法和製造手段的可靠性；證明用縮尺的模型炮代替副炮進行多項目綜合物理模擬試驗技術是成功的。
  13. This paper takes jin ’ ao mansion and adjacent buildings as the study object. first we put the stated reduced scale model in the atmospheric boundary layer which the tunnel simulates, applied the dynamic pressure measure technology on the building ’ s surface to get the mean and fluctuating wind pressure coefficient, drew out the contour of pressure coefficient and analyzed its distributing law and characteristic

    本文以金奧大廈及其鄰近建築作為研究對象，首先把一定縮尺比的模型置於風洞模擬的大氣邊界層環境中，運用建築表面動態測壓技術獲得金奧大廈表面的時均風壓系數和均方根風壓系數，繪制時均風壓系數和均方根等值雲圖並分析其分佈的規律和特點。
  14. Based on the shaking table test of 1 / 4 scale two - bay rc frame modes strengthened with and without cfrp ( carbon fiber - reinforced plastic ), damaged and destroyed model strengthened with cfrp, the vibration properties and seismic response and destroying position of rc frame model with cfrp are analyzed

    摘要通過對兩個縮尺比為1 / 4的兩層單跨鋼筋混凝土框架結構模型的加固、未加固及其震壞后再加固的3次振動臺對比試驗，探討了其動力特性、地震反應和損傷破壞情況。
  15. According to the demand of 《 code for seismic design of building 》 ( gb50011 - 2001 ), furthermore, based on the experimental study of two 1 / 15 reduced - scale shear wall models under low frequency cyclic and reversed lateral loads, the interacting behavior of the r. c frame column and the shear wall is studied, the failure mechanism and energy dissipation mechanism of moderate and tall shear wall with r. c frame column are compared, the seismic behavior is evaluated by the comparison of strength, stiffness, ductility, restoring force characteristics as well as energy consumption ability. it was showed by the experimental results that the earthquake resistant energy dissipation ability of the shear wall with frame column is satisfactory

    因此，為了探討這類剪力墻結構的抗震性能，本文以我國現行《建築抗震設計規范》 （ gb50011 - 2001 ）的要求為基礎，通過1 15的縮尺比，將一縱向框架一剪力墻原型結構中的剪力墻結構模擬為一個試驗模型並對其進行了偽靜力加載試驗，研究了墻板與邊框柱的共同工作性能，分析了帶邊框柱中高剪力墻的受力特點、破壞及耗能機理，並從承載力、剛度、變形、延性及恢復力特性等方面綜合評價了其抗震性能，得出了一些有益的設計理念和方法。
  16. The seismic behavior of longitudinal middling - high r. c shear wall with frame column is discussed through model experimentations and finite element methods in this paper, after taking frame - shear wall structure of a main factory building of the large capacity power plant as experimentative prototype. the major work as follow : in order to appliance pseudo static test, the longitudinal middling - high r. c shear wall with frame column in the large capacity power plant ' s main factory building has been simulated to a model structure with 1 / 15 reduced - scale. the contents of study are process of cracking, course of damage, skeleton curve, rigidity degradation, ductility characteristic etc. that the seismic behavior of this kind of middling - high r. c shear wall is excellent has been proved by chubby hysteretic curve and fine capacity of energy dissipation

    本文以某大型火電廠主廠房縱向框架一剪力墻結構為原型，通過模型試驗和有限元分析，研究了縱向帶邊框柱中高剪力墻結構的抗震性能問題，主要內容有：選用1 15縮尺比把某大型火電廠主廠房縱向帶邊框柱剪力墻原型結構模擬為一個模型結構，並進行了偽靜力試驗，研究了這類縱向帶邊框柱中高剪力墻結構的開裂與破壞過程、骨架曲線、剛度退化、延性性能等問題，試驗滯回曲線飽滿，消能能力強，說明此類中高剪力墻的抗震性能較好。
  17. The major contents are as following : through a test of 1 / 15 - scaled model, the shear wall of a longitudinal frame - shear wall structure main factory building of the large power plant is modeled as testing model structure, and is tested by pseudo static test. this paper mainly investigates the loading behavior, failure proceeding, strength, rigidity, deformation, ductility and energy dissipation capacity of the model structure

    主要內容如下：採用1 15縮尺比，把某大型火電廠主廠房縱向框架?剪力墻原型結構中的剪力墻模擬為試驗模型結構，並對其進行偽靜力加載試驗，研究了此類結構的受力特點、開裂與破壞過程、承載力、剛度、變形、延性及耗能性能等問題。
  18. Vibration characteristics test was carried on a model of one three - spanned prestressed concrete ( pc ) shew continuous box girders, which was designed in jing hu high speed railway of china. we discuss the difference between the results of test and 3d fem analysis with two cases of orthogonality and shew, and explore the dynamic properties of skew box girders

    通過對我國京滬高速鐵路設計中的一座三跨預應力混凝土斜交箱形連續梁橋縮尺模型自振特性參數的測試，比較了正交、斜交箱梁的固有頻率的差異，通過與空間結構分析結果的對比，最後討論了斜交箱梁的動力性能。
  19. Abstract : vibration characteristics test was carried on a model of one three - spanned prestressed concrete ( pc ) shew continuous box girders, which was designed in jing hu high speed railway of china. we discuss the difference between the results of test and 3d fem analysis with two cases of orthogonality and shew, and explore the dynamic properties of skew box girders

    文摘:通過對我國京滬高速鐵路設計中的一座三跨預應力混凝土斜交箱形連續梁橋縮尺模型自振特性參數的測試，比較了正交、斜交箱梁的固有頻率的差異，通過與空間結構分析結果的對比，最後討論了斜交箱梁的動力性能。
  20. The artillery of gc45 155mm was used as an archetype. it was shrunk at the rate of 1 : 6. 738 to design a 23mm simulated artillery. an appropriate propellant was chosen from existing propellants

    利用建立的理論方法，以現有的gc45155mm加榴炮為原型，作被模擬對象，按縮尺比例為1 ： 6 . 738 ，縮小為23mm的模型炮。
分享友人
分享到 Line

分享到臉書